{
  "schemaVersion": "1.0.0",
  "slug": "iphone-16-battery-back-glass-teardown",
  "url": "https://itakeapart.com/teardown/iphone-16-battery-back-glass-teardown/",
  "title": "iPhone 16 Battery & Back Glass Teardown",
  "device": "iPhone 16",
  "category": "phones",
  "kind": "howto",
  "risk": "HIGH",
  "units": "mm",
  "sourceUnits": "mm",
  "difficulty": "Moderate",
  "estimatedTime": "PT1H30M",
  "trademarks": "iPhone and MagSafe",
  "reconstructionNote": "3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.",
  "affiliate": false,
  "parts": [
    {
      "id": "chassis",
      "name": "Aluminium frame and midplate",
      "kind": "Frame",
      "layer": 1
    },
    {
      "id": "display",
      "name": "Display assembly",
      "kind": "Screen"
    },
    {
      "id": "board",
      "name": "Logic board",
      "kind": "Circuit board",
      "layer": 2
    },
    {
      "id": "topCowl",
      "name": "Front camera connector cowling",
      "kind": "Cover",
      "layer": 4
    },
    {
      "id": "camera",
      "name": "Rear camera module",
      "kind": "Cameras",
      "layer": 2
    },
    {
      "id": "topSpeaker",
      "name": "Earpiece speaker",
      "kind": "Speaker",
      "layer": 2
    },
    {
      "id": "trueDepth",
      "name": "Front camera and sensors",
      "kind": "Camera",
      "layer": 2
    },
    {
      "id": "shim",
      "name": "Antenna or shim",
      "kind": "Antenna",
      "layer": 2
    },
    {
      "id": "sim",
      "name": "SIM assembly",
      "kind": "SIM",
      "layer": 2
    },
    {
      "id": "taptic",
      "name": "Haptic motor",
      "kind": "Vibration motor",
      "layer": 2
    },
    {
      "id": "speaker",
      "name": "Bottom speaker",
      "kind": "Speaker",
      "layer": 2
    },
    {
      "id": "mic",
      "name": "Main microphone",
      "kind": "Microphone",
      "layer": 2
    },
    {
      "id": "port",
      "name": "USB-C connector",
      "kind": "Port",
      "layer": 2
    },
    {
      "id": "glass",
      "name": "Back glass with MagSafe coil",
      "kind": "Back glass",
      "layer": 5
    },
    {
      "id": "cover",
      "name": "Middle connector cover",
      "kind": "Cover",
      "layer": 4
    },
    {
      "id": "glue",
      "name": "Battery adhesive",
      "kind": "Electrically released adhesive",
      "layer": 2.5
    },
    {
      "id": "battery",
      "name": "3,561 mAh battery",
      "kind": "Battery",
      "layer": 3
    },
    {
      "id": "coilFlex",
      "name": "Coil cable",
      "kind": "Flex cable",
      "layer": 5
    },
    {
      "id": "foam",
      "name": "Foam block",
      "kind": "Support"
    },
    {
      "id": "cable",
      "name": "USB-C charging cable",
      "kind": "Cable"
    },
    {
      "id": "tray",
      "name": "Magnetic screw tray",
      "kind": "Tray"
    },
    {
      "id": "nineVolt",
      "name": "9 V battery",
      "kind": "Power source"
    },
    {
      "id": "snap",
      "name": "9 V battery snap",
      "kind": "Connector"
    },
    {
      "id": "leads",
      "name": "Clip leads",
      "kind": "Leads"
    },
    {
      "id": "redClip",
      "name": "Red (+) clip",
      "kind": "Alligator clip"
    },
    {
      "id": "blackClip",
      "name": "Black (−) clip",
      "kind": "Alligator clip"
    }
  ],
  "screws": [
    {
      "id": "p2a",
      "code": "P2 pentalobe screw, 7.7 mm",
      "headType": "Pentalobe P2",
      "colorCode": "#a78bfa",
      "lengthMm": 7.7,
      "position": [
        -45.6,
        3.9,
        67.85
      ],
      "toolAffiliateUrl": "https://www.amazon.com/s?k=Pentalobe%20P2%20screwdriver&utm_source=itakeapart_3d&utm_medium=screw_badge"
    },
    {
      "id": "p2b",
      "code": "P2 pentalobe screw, 7.7 mm",
      "headType": "Pentalobe P2",
      "colorCode": "#a78bfa",
      "lengthMm": 7.7,
      "position": [
        -58.4,
        3.9,
        67.85
      ],
      "toolAffiliateUrl": "https://www.amazon.com/s?k=Pentalobe%20P2%20screwdriver&utm_source=itakeapart_3d&utm_medium=screw_badge"
    },
    {
      "id": "y1",
      "code": "Y000 tri-point screw, 1 mm",
      "headType": "Tri-point Y000",
      "colorCode": "#f59e0b",
      "lengthMm": 1,
      "position": [
        -73.7,
        2.85,
        -29.07
      ],
      "toolAffiliateUrl": "https://www.amazon.com/s?k=Tri-point%20Y000%20screwdriver&utm_source=itakeapart_3d&utm_medium=screw_badge"
    },
    {
      "id": "y2",
      "code": "Y000 tri-point screw, 1 mm",
      "headType": "Tri-point Y000",
      "colorCode": "#f59e0b",
      "lengthMm": 1,
      "position": [
        -80.6,
        2.63,
        -11.57
      ],
      "toolAffiliateUrl": "https://www.amazon.com/s?k=Tri-point%20Y000%20screwdriver&utm_source=itakeapart_3d&utm_medium=screw_badge"
    }
  ],
  "dangerZones": [
    {
      "id": "zone-1-volume-buttons-coil-cable",
      "label": "Volume buttons: coil cable",
      "severity": "critical",
      "description": "No pry: Volume buttons: coil cable.",
      "boundingBox": {
        "center": [
          -85.3,
          2.01,
          -37.48
        ],
        "size": [
          5,
          1.86,
          43.01
        ]
      }
    },
    {
      "id": "zone-2-bottom-edge",
      "label": "Bottom edge",
      "severity": "warning",
      "description": "Pick depth · max 3 mm: Bottom edge.",
      "boundingBox": {
        "center": [
          -52,
          0.68,
          65.31
        ],
        "size": [
          51.6,
          1.36,
          5.02
        ]
      },
      "maxInsertionDepthMm": 3
    },
    {
      "id": "zone-3-volume-edge-below-the-buttons",
      "label": "Volume edge, below the buttons",
      "severity": "warning",
      "description": "Pick depth · max 3 mm: Volume edge, below the buttons.",
      "boundingBox": {
        "center": [
          -85.3,
          1.24,
          21.91
        ],
        "size": [
          5,
          2.23,
          71.81
        ]
      },
      "maxInsertionDepthMm": 3
    },
    {
      "id": "zone-4-side-button-edge",
      "label": "Side-button edge",
      "severity": "warning",
      "description": "Pick depth · max 3 mm: Side-button edge.",
      "boundingBox": {
        "center": [
          -18.7,
          1.6,
          -5.99
        ],
        "size": [
          5,
          2.95,
          127.61
        ]
      },
      "maxInsertionDepthMm": 3
    },
    {
      "id": "zone-5-top-edge-to-the-action-button",
      "label": "Top edge, to the Action button",
      "severity": "warning",
      "description": "Pick depth · max 3 mm: Top edge, to the Action button.",
      "boundingBox": {
        "center": [
          -52,
          2.53,
          -77.28
        ],
        "size": [
          51.6,
          1.36,
          5.02
        ]
      },
      "maxInsertionDepthMm": 3
    },
    {
      "id": "zone-6-battery-plastic-tools-only",
      "label": "Battery: plastic tools only",
      "severity": "critical",
      "description": "No metal: Battery: plastic tools only.",
      "boundingBox": {
        "center": [
          -46.5,
          4.21,
          7.05
        ],
        "size": [
          49.4,
          5.01,
          82.04
        ]
      }
    }
  ],
  "steps": [
    {
      "stepNumber": 1,
      "title": "Step 1: Power off and unplug the phone",
      "instruction": "Run the battery right down: Apple’s manual has the flashlight left on until the phone turns itself off, and iFixit asks for below 25% at least. Hold the side button and either volume button, slide the control to power off and pull the USB-C cable out. Then turn the phone over and lay it screen down on a clean, soft part of the mat, its USB-C port towards you: everything from here on is done through the back.",
      "cameraPosition": [
        -134.19,
        452.31,
        430.74
      ],
      "cameraTarget": [
        -44,
        8,
        69
      ],
      "activePartIds": [
        "chassis",
        "display",
        "cable"
      ],
      "explodeVectors": {
        "chassis": [
          0,
          40,
          0
        ],
        "display": [
          0,
          50,
          0
        ],
        "cable": [
          0,
          30,
          0
        ]
      },
      "screwsRemovedInStep": [],
      "dangerZonesActive": [],
      "xrayRecommended": false
    },
    {
      "stepNumber": 2,
      "title": "Step 2: Remove the two P2 pentalobe screws",
      "instruction": "Turn out the two P2 pentalobe screws in the bottom edge, one each side of the USB-C port, and lay them in wells 1 and 2 of the magnetic tray. On the iPhone 16 both are 7.7 mm long, and they hold the back glass at its bottom edge: it will not come away while they are in.",
      "cameraPosition": [
        -160.46,
        75.18,
        204.82
      ],
      "cameraTarget": [
        -52,
        4,
        66
      ],
      "activePartIds": [
        "chassis",
        "tray"
      ],
      "explodeVectors": {
        "chassis": [
          0,
          10,
          0
        ]
      },
      "screwsRemovedInStep": [
        "p2a",
        "p2b"
      ],
      "dangerZonesActive": [],
      "xrayRecommended": false
    },
    {
      "stepNumber": 3,
      "title": "Step 3: Warm the back glass round its edges",
      "instruction": "Lay the warm heat pad along the bottom edge of the back glass, then the right edge, the left and the top, where it drapes over the camera capsule, until each edge is too hot to keep a finger on: about 65 °C by our estimate. The heat softens the adhesive round the glass. Do not go much hotter: the battery lies just beneath it.",
      "cameraPosition": [
        -112.05,
        371.54,
        183.47
      ],
      "cameraTarget": [
        -85,
        6,
        -9
      ],
      "activePartIds": [
        "glass"
      ],
      "explodeVectors": {
        "glass": [
          0,
          50,
          0
        ]
      },
      "screwsRemovedInStep": [],
      "dangerZonesActive": [
        "zone-1-volume-buttons-coil-cable",
        "zone-2-bottom-edge",
        "zone-3-volume-edge-below-the-buttons",
        "zone-4-side-button-edge",
        "zone-5-top-edge-to-the-action-button"
      ],
      "xrayRecommended": true
    },
    {
      "stepNumber": 4,
      "title": "Step 4: Lift the back glass and cut round it at 3 mm",
      "instruction": "Press the suction cup onto the back glass just above the USB-C port and pull up steadily until a thin gap opens, then slip a pick into it, no deeper than 3 mm. Slide it round the bottom right corner and up the right edge, freeing the clip there, and stop well below the volume buttons: the cable of the glass’s MagSafe and charging coil crosses the edge beside the volume-down button. Leave that pick in the seam. Slip a second pick in at the bottom, run it round the bottom left corner, up the left edge and along the top, freeing their clips as they click, and round the top right corner to the Action button. Leave it in too.",
      "cameraPosition": [
        -150.02,
        384.04,
        261.42
      ],
      "cameraTarget": [
        -97,
        6,
        12
      ],
      "activePartIds": [
        "chassis",
        "glass",
        "coilFlex"
      ],
      "explodeVectors": {
        "chassis": [
          0,
          10,
          0
        ],
        "glass": [
          0,
          50,
          0
        ]
      },
      "screwsRemovedInStep": [],
      "dangerZonesActive": [
        "zone-1-volume-buttons-coil-cable",
        "zone-2-bottom-edge",
        "zone-3-volume-edge-below-the-buttons",
        "zone-4-side-button-edge",
        "zone-5-top-edge-to-the-action-button"
      ],
      "xrayRecommended": true
    },
    {
      "stepNumber": 5,
      "title": "Step 5: Swing the back glass open to the right",
      "instruction": "Take both picks out and swing the back glass open to the right, over the volume buttons, like the cover of a book, until it lies face down on the foam block beside the phone. Its one short cable, from the MagSafe and charging coil on its underside, loops over the right edge to the logic board; resting level on the block, the glass pulls on nothing.",
      "cameraPosition": [
        -98.9,
        418.92,
        287.47
      ],
      "cameraTarget": [
        -54,
        6,
        -32
      ],
      "activePartIds": [
        "chassis",
        "glass",
        "coilFlex",
        "foam"
      ],
      "explodeVectors": {
        "chassis": [
          0,
          10,
          0
        ],
        "glass": [
          0,
          50,
          0
        ]
      },
      "screwsRemovedInStep": [],
      "dangerZonesActive": [
        "zone-1-volume-buttons-coil-cable",
        "zone-2-bottom-edge",
        "zone-3-volume-edge-below-the-buttons",
        "zone-4-side-button-edge",
        "zone-5-top-edge-to-the-action-button"
      ],
      "xrayRecommended": true
    },
    {
      "stepNumber": 6,
      "title": "Step 6: Remove the middle connector cover",
      "instruction": "Turn out the two 1 mm Y000 tri-point screws of the middle connector cover, over the battery’s and the coil’s connectors on the logic board, into wells 3 and 4. Put the spudger’s point in one of the cover’s cutouts and slide the cover towards the left edge, off the two hooks that hold its right edge in the board, then lift it away with the tweezers.",
      "cameraPosition": [
        -88.53,
        258.03,
        200.67
      ],
      "cameraTarget": [
        -36,
        6,
        39
      ],
      "activePartIds": [
        "cover",
        "tray"
      ],
      "explodeVectors": {
        "cover": [
          0,
          40,
          0
        ]
      },
      "screwsRemovedInStep": [
        "y1",
        "y2"
      ],
      "dangerZonesActive": [],
      "xrayRecommended": false
    },
    {
      "stepNumber": 7,
      "title": "Step 7: Disconnect the battery, then the back glass",
      "instruction": "Lever the battery’s press connector straight up off its socket with the flat end of the nylon spudger: with it off, nothing in the phone is live. Then pry up the press connector of the back glass’s coil cable, just above it. The glass is free: slide it clear of the phone on its block.",
      "cameraPosition": [
        -85.35,
        275.4,
        225.92
      ],
      "cameraTarget": [
        -38,
        6,
        36
      ],
      "activePartIds": [
        "board",
        "glass",
        "battery",
        "coilFlex",
        "foam"
      ],
      "explodeVectors": {
        "board": [
          0,
          20,
          0
        ],
        "battery": [
          0,
          30,
          0
        ]
      },
      "screwsRemovedInStep": [],
      "dangerZonesActive": [
        "zone-1-volume-buttons-coil-cable",
        "zone-2-bottom-edge",
        "zone-3-volume-edge-below-the-buttons",
        "zone-4-side-button-edge",
        "zone-5-top-edge-to-the-action-button",
        "zone-6-battery-plastic-tools-only"
      ],
      "xrayRecommended": true
    },
    {
      "stepNumber": 8,
      "title": "Step 8: Release the battery’s adhesive with 9 V",
      "instruction": "Peel the battery’s silver tab up off its face with the tweezers to about 45°: it sits at the battery’s bottom edge near its left end, and it belongs to the adhesive, not to the cell. Clip the red (positive) lead to the tab and the black (negative) lead to the screw at the bottom speaker’s lower right, which is grounded to the frame. Only then push the snap onto the 9 V battery, and hold it for 1 minute 30 seconds, as Apple’s manual says: the small current across the adhesive makes it let go of the frame. Take the 9 V battery off the snap first, then the two clips.",
      "cameraPosition": [
        -252.23,
        311.72,
        298.78
      ],
      "cameraTarget": [
        -161,
        6,
        18
      ],
      "activePartIds": [
        "speaker",
        "glue",
        "battery",
        "nineVolt",
        "snap",
        "leads",
        "redClip",
        "blackClip"
      ],
      "explodeVectors": {
        "speaker": [
          0,
          20,
          0
        ],
        "glue": [
          0,
          25,
          0
        ],
        "battery": [
          0,
          30,
          0
        ]
      },
      "screwsRemovedInStep": [],
      "dangerZonesActive": [
        "zone-6-battery-plastic-tools-only"
      ],
      "xrayRecommended": true
    },
    {
      "stepNumber": 9,
      "title": "Step 9: Lift the battery out",
      "instruction": "Press the suction cup onto the middle of the battery and lift it straight up: with its adhesive released, it comes out with the adhesive on its back, without bending. Lay it on the mat away from the phone. If it will not move, clip the leads on for another minute rather than pulling harder. A battery that is swollen, dented or warm goes outside on a non-flammable surface, and every old one to a battery recycling point. Then wipe the last of the clear adhesive off the frame with isopropyl alcohol: Apple wipes it five to ten times.",
      "cameraPosition": [
        -217.64,
        393.62,
        453.84
      ],
      "cameraTarget": [
        -107,
        6,
        68
      ],
      "activePartIds": [
        "glue",
        "battery"
      ],
      "explodeVectors": {
        "glue": [
          0,
          25,
          0
        ],
        "battery": [
          0,
          30,
          0
        ]
      },
      "screwsRemovedInStep": [],
      "dangerZonesActive": [
        "zone-6-battery-plastic-tools-only"
      ],
      "xrayRecommended": true,
      "contextualPartOffer": {
        "partId": "replacement-battery",
        "title": "Replacement battery (3,561 mAh)",
        "priceEstimate": "battery fix kit about $55",
        "vendor": "amazon",
        "affiliateUrl": "https://www.amazon.com/s?k=iPhone%2016%20battery%20replacement%20kit&utm_source=itakeapart_3d&utm_medium=in_scene_step_9",
        "bundledTools": [
          "Suction cup lifter",
          "P2 pentalobe driver",
          "Y000 tri-point driver",
          "Heat pad or hair dryer"
        ]
      }
    }
  ],
  "sources": [
    {
      "label": "Apple: iPhone 16 Battery, repair manual (9 V, red on the silver tab, black on the grounding screw, 1 minute 30 seconds, up to 30 V)",
      "url": "https://support.apple.com/en-us/120642"
    },
    {
      "label": "Apple: iPhone 16 Back Glass, repair manual (the battery flex off first, the torque drivers)",
      "url": "https://support.apple.com/en-us/120638"
    },
    {
      "label": "Apple: iPhone 16 internal view, orderable parts and exploded view",
      "url": "https://support.apple.com/en-us/120648"
    },
    {
      "label": "Apple: iPhone 16 screws and torque drivers (blue 0.65 kgf·cm, green 0.45 kgf·cm)",
      "url": "https://support.apple.com/en-us/120649"
    },
    {
      "label": "Apple: Battery safety (signs of a thermal event, dry sand)",
      "url": "https://support.apple.com/en-us/100299"
    },
    {
      "label": "Apple: iPhone 16 technical specifications",
      "url": "https://support.apple.com/en-us/121029"
    },
    {
      "label": "iFixit: iPhone 16 Battery Replacement",
      "url": "https://www.ifixit.com/Guide/iPhone+16+Battery+Replacement/177286"
    },
    {
      "label": "iFixit: iPhone 16 Back Glass Replacement (7.7 mm P2 screws, picks at 3 mm, the cable by volume-down, the clips)",
      "url": "https://www.ifixit.com/Guide/iPhone+16+Back+Glass+Replacement/177281"
    },
    {
      "label": "iFixit: iPhone 16 Pro and Pro Max teardown (pull tabs, the Pro’s metal-cased battery)",
      "url": "https://www.ifixit.com/News/100693/more-modular-than-ever-before-iphone-16-pro-and-pro-max-teardown"
    },
    {
      "label": "iFixit: iPhone 16 Pro Battery Replacement (7.4 mm P2 screws, pull tabs)",
      "url": "https://www.ifixit.com/Guide/iPhone+16+Pro+Battery+Replacement/180299"
    },
    {
      "label": "MacRumors: iFixit’s iPhone 16 teardown (foil pouches on the 16, 16 Plus and 16 Pro Max)",
      "url": "https://www.macrumors.com/2024/09/23/ifixit-iphone-16-teardown/"
    },
    {
      "label": "Hackaday: the electrically released adhesive and its polarity",
      "url": "https://hackaday.com/tag/tesa/"
    },
    {
      "label": "9to5Mac: iPhone 16 battery capacities from regulatory filings (3,561 mAh)",
      "url": "https://9to5mac.com/2024/09/19/iphone-16-battery-capacities/"
    },
    {
      "label": "Price source: iFixit, iPhone 16 battery fix kit $54.99, the battery alone $49.99, as its iPhone 16 battery guide lists them (27 October 2026)",
      "url": "https://www.ifixit.com/Guide/iPhone+16+Battery+Replacement/177286"
    },
    {
      "label": "Price source: Apple, out-of-warranty battery service estimate, $99 for the iPhone 16 (27 October 2026)",
      "url": "https://support.apple.com/iphone/repair/battery-replacement"
    },
    {
      "label": "Price: Apple Certified Refurbished, iPhone 16 128 GB unlocked, $659 (new from Apple: $829 unlocked; 9 November 2026)",
      "url": "https://www.apple.com/shop/refurbished/iphone"
    }
  ]
}
