Fix it yourself, pay a repair shop, or replace it?
FaultDead battery
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
5 steps · See through it · CR2032 Bitrex trap, copper voice coil & ring-shaped U1 PCB
Apple AirTag Anatomy, Speaker Coil & CR2032: interactive 3D guide
How does an Apple AirTag play a loud Find My chime with zero speaker holes, and why do some brand-new CR2032 batteries refuse to power it on? Peel back the 31.9 mm enclosure in interactive 3D: from the 3-tab bayonet stainless-steel battery cover and the offset negative spring contact blocked by Bitrex bitter coatings, down to the donut-shaped Apple U1 Ultra-Wideband PCB and the copper voice coil that vibrates the plastic body itself as a speaker.
Inside the AirTag: CR2032 bay, ring PCB & body-as-speaker
At 31.9 mm across and 8.0 mm thick, an Apple AirTag has no speaker grille or traditional speaker cone—instead, it turns its own domed white plastic shell into a tactile speaker diaphragm driven by a central copper voice coil and neodymium magnet surrounded by a donut-shaped U1 Ultra-Wideband circuit board. Follow Steps 1–2 for the safe CR2032 battery replacement (and the Bitrex bitter-coating trap), then Steps 3–5 to see how the hidden speaker actuator and U1 board work inside.
Tools: Two thumbs (battery swap) / thin plastic pick
- Always keep new and used CR2032 coin cells out of reach of children, and check the packaging for “Compatible with Apple AirTag” or wipe the negative face with isopropyl alcohol.
Apple AirTag (`A2187`) Hardware & CR2032 Battery Compatibility Reference
Apple AirTag CR2032 Battery Compatibility (Bitrex Coating Rule) & Internal Hardware Specs
Because the AirTag’s negative (−) battery spring pin is offset toward the outer perimeter of the coin cell (to clear the central speaker magnet), CR2032 batteries with a perimeter ring of Bitrex bitterant coating can fail to make electrical contact:
| Component / Subsystem | Part Code / Specification | Physical Layout in AirTag (`31.9 × 8.0 mm`) | Key Technical / Repair Detail |
|---|---|---|---|
Uncoated CR2032 Coin Cell | CR2032 (3.0 V · 20.0 × 3.2 mm · ~225–240 mAh Li-MnO₂) | Sits + side UP under the 3-tab bayonet stainless-steel cap | Works immediately: bare stainless-steel negative underside makes clean contact with the offset − spring pin |
Bitrex Bitter-Coated CR2032 | Child-deterrent CR2032 with denatonium benzoate (Bitrex) coating | Clear bitterant is often printed in a perimeter ring on the − face right over the AirTag’s offset − pin | Fix: Look for “Compatible with Apple AirTag” on the pack, or rub the − face perimeter for 15 s with 90%+ isopropyl alcohol / damp cloth |
| Tactile Speaker Actuator | 12 mm copper voice coil + central neodymium magnet + steel flux cup | Occupies the dead-center hole of the AirTag; drives the inner dome & white polycarbonate shell as a diaphragm | No external speaker holes needed (preserves IP67 water resistance); 0.05 mm coil leads tear if pried |
| Annular (Ring) Main PCB | Apple U1 UWB (6.5 / 8 GHz) + Nordic nRF52832 BLE 5.0 + NFC + 3-axis accelerometer | Donut-shaped multi-layer PCB (30 mm OD, 14 mm ID) encircling the speaker magnet assembly | Carries the 3 gold battery spring prongs (2 × + outer rim, 1 × − offset inner ring) and 2 voice-coil pads |
No matching series found. Clear the filter to view all compatible models.
Apple Support Guidance on CR2032 Bitter Coatings: Apple explicitly notes that *"CR2032 batteries with bitterant coatings might not work with AirTag or other battery-powered products, depending on the alignment of the coating in relation to the battery contacts."* Wiping the negative face with rubbing alcohol removes the insulating bitterant film in seconds.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the closed AirTag: the 3 bayonet locking tabs on the stainless-steel cover, the CR2032 coin cell and the 3 spring-loaded battery contacts underneath (including the offset negative pin), the ring-shaped U1 Ultra-Wideband PCB, and the central copper voice coil and neodymium magnet that vibrate the body as a speaker.
Bitrex contact ring, copper voice coil & U1 ring PCB zones
- No Bitrex ring CR2032 negative perimeter ring: Bitrex coating blocks offset (−) pin
- 0.05 mm wire · max 1.5 mm Copper voice-coil winding: hair-thin leads tear if inner frame is pried
- U1 Ring PCB Annular main PCB: Apple U1 Ultra-Wideband + BLE 5.0 + NFC coil
3 bayonet locking tabs (twist 15° CCW)
- Bayonet tab 1 of 3
- Bayonet tab 2 of 3
- Bayonet tab 3 of 3
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed AirTag.
All 5 steps
- 1Press down & twist the polished stainless-steel cover 15° counter-clockwise
Place two fingers or thumbs firmly on the polished stainless-steel battery cover to compress the 3 spring-loaded battery contacts underneath, rotate the cover 15° counter-clockwise until its 3 bayonet locking tabs reach the release slots, and lift the steel cover straight off.
- 2Lift out the CR2032 coin cell & inspect the 3 offset spring contacts trap
Lift the old 3 V CR2032 coin cell out of the bay and inspect the 3 gold-plated spring prongs rising through the floor: two outer prongs touch the positive (+) rim while one offset inner prong touches the negative (−) underside near its perimeter. Insert a fresh uncoated CR2032 battery with the positive (+) side facing UP. Avoid this trap: Unlike devices whose negative contact touches the dead-center of the coin cell, the AirTag’s central cavity is occupied by its speaker magnet—forcing Apple to place the negative (−) spring contact near the outer edge of the negative face. Many child-safe CR2032 cells apply an invisible ring of bitterant (denatonium benzoate / Bitrex) in that exact perimeter zone, acting as an electrical insulator so the AirTag never powers on.
- 3Separate the inner plastic speaker frame without cutting the voice coil trap
Routine battery replacement stops at Step 2! To see how the AirTag works inside, the ultrasonic-welded inner plastic speaker frame lifts away from the white outer shell—exposing the hair-thin copper voice-coil lead wires soldered to two gold spring pads on the ring PCB. Avoid this trap: The copper voice coil is bonded directly to the underside of the plastic speaker diaphragm, and its two hair-thin enamelled copper lead wires bridge across the seam to the ring PCB. Prying the welded plastic speaker frame with a metal pick catches and snaps the fragile coil wire—leaving the AirTag silent when pinged in Find My.
- 4Examine the Copper Voice-Coil Winding & Speaker Dome Magnet Assembly
Here is how an AirTag makes sound with zero speaker holes: a cylindrical neodymium magnet and steel yoke sit in the center of the base, surrounded by a suspended copper voice-coil winding attached to the inner plastic dome. When audio current pulses through the copper coil, Lorentz forces drive the inner dome against the white outer shell—turning the entire AirTag body into a resonant tactile speaker cone while keeping the enclosure IP67 sealed.
- 5Inspect the Ring-Shaped Main PCB: Apple U1 Ultra-Wideband, BLE & NFC
Wrapped tightly around the central speaker magnet is a masterpiece of high-density packaging: a ring-shaped (annular) multi-layer main PCB. On this narrow black donut sit the Apple U1 Ultra-Wideband (UWB) chip for Precision Finding distance and angle arrows, a Nordic nRF52832 Bluetooth Low Energy SoC for Find My broadcasts, a 3-axis accelerometer, 32 MB serial flash, and a perimeter NFC antenna coil for Lost Mode tap-to-read.
What you need
- Uncoated CR2032 3 V lithium coin battery · 20.0 × 3.2 mm, without a Bitrex bitterant ring on the negative contact zone
- Two thumbs (no tools needed for battery swap) · press down on the stainless-steel cover and rotate 15° counter-clockwise
- 90%+ Isopropyl alcohol & cotton swab (optional) · to wipe the invisible Bitrex coating off a child-deterrent CR2032 if it does not chime
Questions
Why does my AirTag not work or chime with a brand-new CR2032 battery?
Many CR2032 batteries (such as Duracell, Energizer, and Panasonic child-resistant packs) have an invisible ring of bitterant (Bitrex) printed near the outer edge of the negative (−) face. Because the AirTag’s negative spring pin is offset from the center to clear the speaker magnet, it lands right on that insulating Bitrex ring. Rub the negative underside firmly with a cotton swab dampened with 90%+ isopropyl alcohol (or a damp cloth) for 15 seconds, dry it, and reinsert + side up.
How does an Apple AirTag make sound without a speaker hole?
Inside the center of the AirTag is a cylindrical neodymium magnet and a copper voice coil attached to an inner plastic dome diaphragm. When audio current flows through the coil, it vibrates the dome and the white outer polycarbonate shell itself like a drumskin—turning the entire body of the AirTag into a sealed speaker.
Which way up does the CR2032 battery go in an AirTag?
The flat positive (+) side with the engraved “CR2032 / +” text faces UP toward you (and touches the underside of the stainless-steel cover when closed), while the textured negative (−) side faces DOWN into the AirTag onto the spring contacts.
Why does the AirTag have a donut-shaped (ring) circuit board?
To keep the AirTag only 8.0 mm thick, Apple placed the tall neodymium speaker magnet and voice coil right through the center of the enclosure and wrapped a ring-shaped PCB around it. That narrow ring holds the Apple U1 Ultra-Wideband chip, Bluetooth LE SoC, accelerometer, and perimeter NFC coil.
Safety
Keep CR2032 coin cells—new and old—out of children’s reach at all times: a swallowed lithium coin battery can cause severe internal burns in under two hours. Tape both faces of the used CR2032 cell before recycling.
- Coin cells: keep button and coin batteries, new and old, away from children: one that is swallowed can burn through tissue within hours. If you think one has been swallowed, get emergency help at once. Tape an old cell’s faces before you recycle it.
- Static (ESD): work on an anti-static mat with a grounded wrist strap; a spark you cannot feel can kill a chip.
About this guide
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
This 3D anatomy and battery guide models the Apple AirTag (model A2187, 31.9 mm diameter × 8.0 mm height). Unlike conventional trackers that use a separate piezoelectric buzzer and speaker grille, the AirTag uses its central cavity for a cylindrical neodymium magnet and copper voice coil bonded to the inner plastic diaphragm—driving the outer shell itself as a speaker cone while keeping the enclosure sealed to IP67.
Because the central voice-coil magnet occupies the middle of the AirTag, both the multi-layer logic board (carrying the Apple U1 Ultra-Wideband chip, Nordic nRF52832 Bluetooth LE SoC, and NFC coil) and the negative (−) battery spring contact are arranged in a ring around the magnet. That offset negative pin explains why CR2032 batteries printed with a perimeter ring of Bitrex child-deterrent bitterant often fail to power an AirTag until wiped with isopropyl alcohol.
Sources: Apple Support: How to replace the battery in your AirTag (press down on polished stainless steel battery cover, rotate counter-clockwise, insert CR2032 positive side up, warning on bitterant-coated CR2032 batteries), iFixit: Apple AirTag Teardown (ring-shaped donut PCB around central speaker magnet, copper voice coil attached to inner plastic diaphragm, 3 bayonet tabs & offset battery contacts), Price: Apple, AirTag, $29 new (9 November 2026), Price: Digi-Key, Panasonic CR2032 lithium coin cell, $0.40 for one (9 November 2026; the page does not say whether it is coated).
The 3D models, drawings and text are our own. Apple and AirTag are trademarks of their owners, named only to say which device this guide is for; iTakeApart is not affiliated with them.