How to build a gaming PCGaming PCGaming PC

Steps ↓
Concept model Risk: Med ~2 h
Teardown · step by step Gaming PC

Illustrative 3D Concept Model — Generic Layout

🟡 Overall risk: Medium ⏱ About 2 hours 💰 DIY vs. Shop
Step0/10
RAM channel—
PCIe lanes—
Power cables0/4
CPU temp—°C
What you need10 steps · press play

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this teardown.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itDIY or a repair shop?
Overall repair riskMedium
Time requiredAbout 2 hours
What can go wrongBoth memory sticks put side by side in A1 and A2 (single channel), the plastic film left on the cooler’s base, an extra standoff under the board, or the monitor plugged into the motherboard instead of the graphics card.
Cost comparison DIY: two Phillips screwdriversGet the part ↗ Shop build fee: varies by shopSearch nearby repair shops ↗Opens local search results in Google Maps
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

FaultBuilding a new PC

Your time is worth
Fix it yourselfNo sourced figure
  • PartNo sourced figure
  • Toolsnot priced
  • Time2 h
  • 3D risk levelMedium
Repair shopNo sourced figure
New or refurbishedNot a repair
No verdict: a figure is missingNothing is broken here: this guide is not a repair.

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. We found no fair, sourced figure for this yet, so the card gives no verdict it cannot back. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

10 steps · 2 traps to avoid · an ATX board in a mid-tower case

How to build a gaming PC: interactive 3D teardown

Illustrative 3D Concept Model — Generic Layout

Building a PC is mostly plugging the right part into the right slot, the right way round. Every step from the processor to the first power-on, in 3D. Press play to watch a step, drag to look around, or switch to Drawing for a technical drawing’s black lines.

What you need

An ATX case, an ATX motherboard, a processor, an M.2 NVMe drive, two DDR5 memory sticks, a tower cooler with thermal paste, a graphics card and a modular power supply. Tools: a No. 2 Phillips screwdriver, and a No. 0 for the M.2 drive’s tiny screw.

Tools: Phillips screwdrivers

Before you open it: the risk map

Seen across the build: the LGA processor socket that takes zero force, the A2 and B2 memory slots for dual channel, the cooler’s plastic film to peel off, and the nine brass standoffs in the case.

Before you build it

Key connectors and fasteners

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed PC.

All 10 steps

  1. 1Fit the processor

    Lift the socket’s lever and open its load plate. Hold the processor by its edges, line up the gold triangle on its corner with the triangle on the socket, and lower it straight in: it fits only one way and needs no force. Close the plate and push the lever down under its hook; the socket’s plastic cover pops off.

  2. 2Fit the M.2 drive

    Slide the M.2 drive into the top M.2 slot at an angle: once it is fully in, it stands up about 35 degrees. Push its free end down to the standoff and fix it with its tiny screw.

  3. 3Fit the memory in A2 and B2 trap

    With two sticks, use the second and fourth slots from the processor, A2 and B2, as most boards’ manuals say. Open the latches, line up the notch, and press each stick straight down until both latches click shut. Avoid this trap: The slots come in pairs: A1 and A2 are one channel, B1 and B2 the other. With both sticks in A1 and A2 they share one channel, so the memory runs in single channel, with half the peak bandwidth it would have in dual channel. Two sticks go in A2 and B2.

  4. 4Fit the cooler trap

    Squeeze a dot of thermal paste no bigger than a grain of rice onto the middle of the processor. Peel the clear film off the cooler’s base. With its fan unclipped, set the cooler on and tighten its four screws a little at a time in a cross pattern, so it presses down evenly and spreads the paste; a long screwdriver reaches them past the fins. Then clip the fan back on. Avoid this trap: Most coolers come with a clear plastic film over their base to protect it. Left on, it sits between the paste and the metal and stops the heat getting into the cooler: the processor runs far too hot and slows itself down to protect itself. Peel the film off before the cooler goes on.

  5. 5Fit the board into the case

    Check the case’s brass standoffs line up with the board’s holes: an ATX board takes nine, and there must be none where the board has no hole. Lower the board onto them, its ports into the back’s opening, and screw it down with nine screws, firmly but not too tight.

  6. 6Fit the power supply and route its cables

    Set the power supply into its place at the bottom of the case, its fan facing the case’s vent, and screw it in. Plug the cables you need into it and lead them behind the tray and through the rubber grommets: the 24-pin to the board’s side, the 8-pin to its top corner, and the card’s cables up through the shroud.

  7. 7Fit the graphics card

    Take out the two slot covers at the back level with the top PCIe x16 slot, the longest one. Line the card up with the slot and push it straight down until it clicks, then screw its bracket to the case.

  8. 8Plug in the power cables

    Plug the 24-pin cable into the board’s side, the 8-pin processor cable into its top corner and the PCIe cables into the graphics card, each until its clip locks.

  9. 9Plug the monitor into the graphics card

    Plug the monitor’s cable into one of the graphics card’s display ports, in the row of slots at the back, not into the video port in the board’s panel above it.

  10. 10Power it on

    Switch the power supply on and press the case’s power button. The fans spin, and the firmware’s screen shows the memory in dual channel and the card in its x16 slot.

What you need

Questions

Which slots do two memory sticks go in?

On most boards the second and fourth from the processor, A2 and B2, as ASUS’s FAQ says for its boards. Check your board’s manual: it marks the slots to use.

How much thermal paste should I use?

Intel’s guide says a dot no bigger than a grain of rice in the middle of the processor: the cooler’s pressure spreads it.

How many standoffs does an ATX motherboard need?

An ATX board usually takes nine screws, so nine standoffs where its holes are, and no extra ones under it.

Where do I plug the monitor in?

Into the graphics card’s ports, at the back in the row of slots, not the video port on the motherboard’s panel.

Do I need force to fit the processor?

No. Intel’s guide says it fits only one way and needs no force; only the socket’s lever may need a firm push.

Safety

Unplug the power supply before you work inside the case, and never open a power supply: it holds a charge. Static can damage the parts: work on a hard floor and touch the case’s bare metal before you handle them.

About this teardown

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

This guide shows an ATX motherboard with an LGA socket, two DDR5 sticks, an M.2 NVMe drive, a tower cooler, a graphics card and a modular power supply in a mid-tower case. The steps follow Intel’s guide to building a gaming PC; the memory slots are the ones ASUS’s FAQ gives for two sticks on its boards. Your board’s manual has the final word on its own slots and connectors.

The temperatures on the readings are illustrative.

Sources: Intel: How to build a gaming PC, ASUS FAQ: which memory slots to use.

The 3D models, drawings and text are our own. The device shown is a generic one of our own design, not any one maker’s model.