How to Clean a Kitchen or Bathroom Sink P-TrapSink P-trapSink P-trap

Steps ↓
Concept model Risk: Low ~20 min
Teardown · step by step Sink P-trap

Illustrative 3D Concept Model — Generic Layout

🟢 Overall risk: Low ⏱ About 20 min 💰 DIY vs. Shop
Step0/6
Slip nuts tight2/2
Water flowBLOCKED
What you need6 steps · press play

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this teardown.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itDIY or a repair shop?
Overall repair riskLow
Time requiredAbout 20 min
What can go wrongA tapered washer put back upside down, so the joint drips, or a plastic slip nut cracked by overtightening.
Cost comparison DIY: no toolsGet the part ↗ Plumber: varies by areaSearch nearby repair shops ↗Opens local search results in Google Maps
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

FaultSlow or smelly sink drain

Your time is worth
Fix it yourself$8
  • Part$0
  • Toolsnone needed
  • Time20 min
  • 3D risk levelLow
Repair shopNo sourced figure
New or refurbishedUpkeep: nothing to replace
No verdict: a figure is missingNothing to buy new, and no sourced shop price to compare with: no verdict.

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in ; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

6 steps · No plumber, no tools · a 1¼-inch plastic trap · 1 trap to avoid

How to Clean a Kitchen or Bathroom Sink P-Trap Step-by-Step

Illustrative 3D Concept Model — Generic Layout

A slow or blocked bathroom sink is usually clogged in its P-trap, the U-shaped bend under it. Every step of taking it off, cleaning it and putting it back without leaks, in 3D. Press play to watch a step, drag to look around, or switch to Drawing for a technical drawing’s black lines.

What you need

A bucket or a bowl to catch the water, an old towel, rubber gloves and a bottle brush. No tools: the slip nuts on a plastic trap undo by hand. Slip-joint pliers help only if one is stuck.

Before you open it: the risk map

Seen through the trap: the water standing in its U-bend, the tapered washer under each slip nut, the nuts hand-tight plus a quarter turn, and the drain no chemical cleaner should be in.

Before it comes apart

Points to know

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed trap.

All 6 steps

  1. 1Put a bucket under the trap

    Open the cabinet under the sink and set a bucket on its floor, right under the U-shaped bend of the trap: there is always water standing in it, and it comes out when the bend does.

  2. 2Undo the two slip nuts

    Unscrew the two big slip nuts at the top of the U-bend by hand: anticlockwise as you look down on them. When each one comes off its thread, slide it up its pipe, out of the way.

  3. 3Take off the U-bend and empty it

    Pull the U-bend straight down, off the tailpiece from the sink and the trap arm from the wall, and tip it over the bucket: the water and whatever is clogging it fall out.

  4. 4Brush it clean

    Push a bottle brush through the U-bend from both ends to scrub off the grease and hair, then rinse it out in another sink or a bucket of water. Look into it: it should be clear all the way round.

  5. 5Check the washers trap

    Each pipe going into the U-bend wears a slip nut and, under it, a tapered washer. Check both washers: the thin, tapered side faces down into the U-bend and the flat side up against the nut. A cracked or squashed washer leaks: replace it. Avoid this trap: A slip washer is tapered so that the nut pushes its thin edge down into the U-bend’s mouth and wedges the joint shut. Turned over, its flat side meets the mouth, the nut squashes it unevenly, and water seeps past it and drips from under the nut as soon as the tap runs. Take the nut off and turn the washer round: tapered side down into the bend.

  6. 6Put it back and run the tap

    Push the U-bend back up onto both pipes, slide the slip nuts down and screw them on by hand, then give each about a quarter turn more to seal. Run the tap for 30 seconds and look under each nut: no drips.

What you need

Questions

Why does a sink have a P-trap?

The water that always stands in its U-bend stops sewer gas coming up the drain into the room. It is also where hair, soap and grease collect, so it is where most sinks clog.

Do I need tools to take a P-trap off?

Usually not: a plastic trap’s slip nuts undo by hand. Slip-joint pliers help if one is stuck; wrap a cloth round a metal nut so they do not scratch it.

Which way does the slip washer go?

Tapered side down, into the U-bend, with the flat side up against the slip nut. The trap maker’s sheet puts it as “cone side down, into the lower side of the trap”.

How tight should the slip nuts be?

Hand-tight, then a little more, about a quarter turn, to seal. Overtightening cracks plastic nuts. Check them again for drips after two or three days.

It still drips after putting it back. What now?

Undo the nut that drips and check its washer: it may be upside down, cracked or squashed. Put it the right way round, or fit a new one, and tighten again.

Safety

Wear gloves: the water in a trap is dirty. Do not pour chemical drain cleaner into a sink you are about to take apart, and if you already have, wear eye protection and let a plumber do it.

About this teardown

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

This guide shows a common bathroom sink’s plastic P-trap, 1¼ inches (32 mm) across: a tailpiece from the basin, a U-bend held on by two slip nuts, each over a tapered washer, and a trap arm into the wall. A kitchen sink’s trap is usually 1½ inches and comes apart the same way.

The steps follow a P-trap maker’s instruction sheet: pull the bend straight down to take it off; the rubber washer goes cone side down into the trap; hand-tighten every nut, then a little more to seal, and test for leaks. The water-flow readings are illustrative.

Sources: P-trap installation instructions (sheet sold with a trap at Lowe’s), iFixit: How to unclog a sink.

The 3D models, drawings and text are our own. The device shown is a generic one of our own design, not any one maker’s model.