How a click pen worksClick penClick pen

Steps ↓
Concept model Risk: Low ~2 min
How it works · in 3D Click pen

Illustrative 3D Concept Model — Generic Layout

🟢 Overall risk: Low ⏱ About 2 min to change a refill (our estimate) 💰 DIY vs. Shop
Step0/9
TipIn
Cam step0/6
RidgesIn gaps
Spring26.0mm
What is inside9 steps · press play

3D Spatial Reconstruction: a generic model of our own design, built from published facts to show how the parts work together. Real ones differ by maker and model: always check your own before you open or adjust it.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this guide.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itCan it be opened at home?
Overall repair riskLow
Time requiredAbout 2 min to change a refill (our estimate)
What can go wrongA refill of the wrong length, the spring left out or lost, or a worn cam that no longer holds the tip out.
Cost comparison DIY: a refill of the same lengthGet the part ↗Get the kit ↗ Shop: a pen shop, for a fine penSearch nearby repair shops ↗Opens local search results in Google Maps
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

FaultPen that will not click or write

Your time is worth
Fix it yourselfNo sourced figure
  • PartNo sourced figure
  • Toolsnone needed
  • Time2 min
  • 3D risk levelLow
Repair shopNo sourced figure
New or refurbishedUpkeep: nothing to replace
No verdict: a figure is missingNo sourced price for the part, so no verdict.

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. We found no fair, sourced figure for this yet, so the card gives no verdict it cannot back. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

9 steps · 6 teeth · 3 stops, 3 gaps · 60° a click · 3 traps to avoid

How a click pen works: interactive 3D guide

Illustrative 3D Concept Model — Generic Layout

A click pen does not remember whether it is open: each press only turns a small cam one step. Work this one yourself: Click Pen presses the plunger, in real time, and Top-Down Cam View looks straight down the pen at the stops and the gaps. Press play for the story step by step, Explode to spread the parts along the pen, Reassemble to put it back together with a new refill.

What is inside

A click pen has no switch and nothing that could remember anything. Through its blue barrel you can see all there is: a plunger with slanted teeth, the yellow cam those teeth press on, three white stops fixed inside the barrel with three gaps between them, a coil spring in the nose, and the ink refill the spring pushes up. The tip is in. Press Click Pen under the picture to work it yourself, and Top-Down Cam View to look straight down at the cam.

Before you open it: the risk map

Seen through the closed pen before you unscrew it: the spring that pushes the halves apart, the stops whose notches wear, and why the tip’s place depends on the refill’s length.

What to watch for

What to find first

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed pen.

All 9 steps

  1. 1Look through the barrel

    Look for whatever remembers that the pen is open: there is nothing of the kind. The plunger is a button with teeth. The cam is a yellow sleeve that sits loose on top of the refill. The spring is an ordinary coil. The refill is a tube of ink with a ball in its tip. Only the stops are fixed, and they are simply shapes inside the barrel. All the pen’s behaviour comes from how these few shapes meet.

  2. 2Press the plunger lightly and let go trap

    The spring stands on a seat inside the nose, its narrow end round the refill’s nib, and pushes up on the refill’s collar. It is squeezed even with the tip in, so it pushes all the time, and left alone the refill rides up until the plunger’s flange stops under the lip of the barrel. Press the plunger a little and the spring gives; let go and it pushes everything back up. The tip always wants to hide: the mechanism’s only job is to hold it out, and to let it go. Avoid this trap: Put the pen back together without its spring, or lose it when the barrel comes apart, and nothing is left to lift the refill. It slides down until its nib jams in the nose, the cam and the plunger follow it, and the button sinks into the barrel and stays there: press it and you feel no resistance and no click. The tip hangs out, with nothing to hold it against the paper. Keep the spring on the refill’s nib when you change a refill. A spring from another pen of similar size can stand in, as long as its length and its coils are close. How far the refill falls here comes from our own model.

  3. 3Press the plunger down

    Press the plunger. Its teeth rest on the cam’s, and the cam rests on the refill, so all of them go down together against the spring. The cam’s three ridges slide down the gaps between the stops, and the gaps’ walls keep it from turning, until the ridges come out below the stops. Nothing stops the plunger yet: it keeps going until its button is level with the top of the barrel.

  4. 4Hold it down and watch the cam turn

    Below the stops, nothing holds the cam. The plunger cannot turn, so as it keeps pressing its teeth slide down the slopes of the cam’s teeth, and that pushes the cam round: 48° in this pen, most of one 60° tooth, until the two sets of teeth have closed up together. This is why the teeth are slanted: a straight push down becomes a turn. It is the only part of the pen that changes anything, and all it changes is an angle.

  5. 5Let go of the plunger trap

    Let go and the spring lifts everything back up, the plunger riding on the cam. The cam has turned, so its ridges now come up under the stops instead of into the gaps. Their slanted tops meet the stops’ slanted undersides, which turn the cam the last 12° of the step, until each ridge stops against the wall of a small notch. There it stays: the spring pushes up and the stops push down, and the tip is held out, ready to write. Press on the paper and it has nowhere to go. Avoid this trap: A tip that slips back means the cam is not latching, and ageing plastic is one cause. Here the corner of the notch under a stop has worn away: the ridge reaches the stop’s slope as it always did but nothing stops it there, so it slides on off the stop’s end and up the gap, and the tip goes back into the pen with no second click. Dirt or a misaligned part can stop a cam latching too, so clean the parts first; but if you see cracks or missing teeth, replacing the pen beats repairing it. Which corner wears and how the ridge slips is our picture.

  6. 6Click it again

    A second press takes the cam down off the stops, and below them the teeth turn it again. Coming back up, the ridges catch the short slope at the end of the stops, which finishes the step and leaves them in line with the gaps. Now nothing blocks them. The spring drives the cam, the refill and the plunger up until the plunger’s flange stops under the barrel’s lip, and the tip is back inside the nose. Same press, same teeth, same turn: the only difference is where the last click left the cam.

  7. 7Look straight down the pen

    From above, the plunger out of the way, the whole trick is one picture: stop, gap, stop, gap, three of each, 120° round from one stop to the next. The cam has 6 teeth, so a click turns it 60°, exactly the distance from a stop to the next gap. One click lands its ridges on the stops, the next in the gaps, and so on for ever: six clicks and the cam has gone once round. The pen does not remember whether it is open. It has just turned.

  8. 8Unscrew the barrel and lift out the refill trap

    To change a refill, hold the two halves together and unscrew them, because the spring is pushing them apart. In this pen the upper half lifts away with the plunger inside it, the cam comes off the top of the refill, and the refill lifts out of the lower half with the spring on its nib. Keep the spring on it, and note which way round it goes: its narrow end grips the refill. A new refill must be the same length as the old one. Avoid this trap: The cam only moves the refill a fixed distance, so the refill’s length decides where that travel falls. Fit one too short, or lose a spacer that a pen needs on its refill, and the cam locks on its stops as it should while the tip stays inside the nose: the pen clicks, and does not write. In some pens a wrong length stops the cam latching at all. Fit one too long and it goes the other way: the tip will not go back far enough when the pen is clicked shut. A millimetre can matter on a pen with little travel, so measure the old refill and buy the same length. Here the refill is 11 mm short, and the 11 mm is our picture.

  9. 9Slide out the plunger

    With the upper half lying on its side, the plunger slides out of its open end, its flange passing between the stops. That is every part of this pen laid out: the upper half with its stops, the plunger, the cam, the lower half still in the cradle, and the refill with its spring. Some pens have their mechanism pressed or glued in, and it stays there: to change a refill you need not go further than the step before.

What is in it

Questions

How does a click pen remember whether it is open?

It does not. Each click turns a small cam one step, always the same way. One step puts its ridges under the stops in the barrel, which hold the tip out; the next puts them in line with the gaps, and the spring takes the tip back in. There is no memory, only where the cam was left.

What do the slanted teeth do?

They turn a straight press into a turn. The plunger cannot rotate, so when it presses on the cam once the cam is clear of the stops, its teeth slide down the cam’s slopes and push the cam round.

Why does a click pen take two clicks to go in and out?

Because the stops and the gaps take turns: a step that lands the ridges on the stops is followed by one that lands them in the gaps. With 6 teeth, 3 stops and 3 gaps, a click is 60°, exactly from a stop to a gap.

What does the spring do in a pen?

It pushes the refill up all the time, so the tip always wants to hide. It is also what lifts the cam and, in a pen like this one with no second spring, pushes the plunger back up after a press.

Why won’t the tip of my pen stay out?

The cam is not latching. Dirt, a burr on a plastic part or a misaligned part can stop it, so take it apart and clean it first. If you see cracks or missing teeth, a new pen is the better fix.

Why does my pen not write after I changed its refill?

The new refill may be too short: the cam can lock on its stops with the tip still inside. Some pens also use a spacer on the refill’s end that is easy to lose. Measure against the old refill.

My pen’s tip will not go back in. Why?

The refill may be too long for the pen, the spring may be on backwards, jammed in the nib or weak, or the nib may be catching in the nose. Check which way round the spring is, and try the refill alone in the nose: it should slide freely.

Which way round does a pen’s spring go?

One end is often narrower or wound tighter: that end goes onto the refill first. Put on backwards it can bind, and the refill will not go back. Check your own pen’s old refill before you take the spring off.

Safety

A pen is about as safe as a mechanism gets, but the spring is pushing its two halves apart: hold them together as you unscrew them, and do it over a table, so that a small part or the spring does not fly off and get lost or swallowed by a small child. Ink stains: keep a tip clear of your clothes and work on something you can wipe.

About this guide

3D Spatial Reconstruction: a generic model of our own design, built from published facts to show how the parts work together. Real ones differ by maker and model: always check your own before you open or adjust it.

The pen is a generic one of our own design, not any maker’s, about 140 mm long, and its proportions are our own picture: its barrel is drawn fatter than a real pen’s, and its tip’s travel of 11 mm is longer than the few millimetres a real one needs, so that the parts can be seen working. The counts are what make it work, and they are the same arithmetic real pens use: 6 teeth on the plunger and the cam, a 60° step; 3 ridges, and 3 stops and 3 gaps 120° apart, so that one step takes a ridge from a stop to a gap. Published designs use other numbers: a patent filed in 1955 (Weisser) describes four lugs, and a recent one has four teeth and four grooves in the barrel with eight teeth on the member that presses the cam.

Where this guide differs from our own video: the video draws flat stops and flat ridges and has the plunger’s teeth turn the cam the whole step. Teeth pressed together can only turn a cam as far as the point where they mesh, and from there nothing could drive it on at the next press, so here the turn is shared, as it is in Weisser’s patent: the teeth turn the cam while it is pressed clear of the stops (48° of the 60° here, our choice), and on the way back up inclined faces on the ridges and the stops turn it the rest (12°). The ridges are wider than the video’s, 52° in a 54° gap, so that the gaps guide them.

On the real thing the barrel’s slanted faces are longer, and a press may turn the cam only slightly: the patent has a lug rotate “slightly” once it clears its channel. In Weisser’s design the spring in the nose is the only spring, as here; the 1954 pen in the Engineer Guy’s video has two. Readers report that the refill turns with the cam in some pens; in ours it does not. The notch’s wall under each stop is our own simple version of what a real barrel does with the shallow channels between its teeth. The plunger’s flange, the spring’s seat and the thread’s pitch are our own design.

The traps are real failures reported by repairers and by people who build pens, in the sources below: a missing spring, a refill of the wrong length or one missing its spacer, and a cam that no longer latches. How each plays out here, how far the refill falls and how the notch wears, is our picture of it, not a measurement.

Sources: Weisser, US patent 3,137,276 (push-button mechanism): lugs on a rotating member, channels and teeth inside the barrel, deep channels for the retracted position and shallow ones that block a wider lug for the protracted one, inclined faces that turn it on release, one spring, US patent 10,538,124 (retractable writing instrument): cam teeth and cam grooves alternating on the barrel’s inner face, a rotary member with four protuberances, eight sawtooth cam projections, Pens.com, parts of a pen: the cam (thrust device) over the ink cartridge, with grooves, slants and ledges that hold it in a different place each click; the spring at the nose keeps it retracted, Make: how does a retractable pen work? (the Engineer Guy’s video: a cam body, a tubular plunger and stop members), The Tools Trunk, how to fix a pen that won’t click: a button that sinks with no resistance means a missing or damaged spring; a tip that slips back means the cam is not latching (dirt, misalignment, wear); a wrong cartridge length leaves the cam short of latching; replace a pen with cracks or missing teeth, International Association of Penturners, “pens won’t click”: click pens that will not retract; the refill’s spring put on backwards, its small end belongs up towards the pen; a kit finicky about refill length, International Association of Penturners, “Sierra click problem”: a metal extender on the refill’s rear end, lost, stops the pen working; longer refills; a nib that will not retract, International Association of Penturners, “Click pen problem”: a tip that does not extend far enough to write; a refill too short could cause it, International Association of Penturners, “Gatsby clicker problem”: a rib in the housing lines up with a slot on alternate pushes; with the housing loose the tip never stays out, International Association of Penturners, “45 caliber click pen won’t retract refill”: the original spring lost; substitutes tried, Retro 51, repair requests: the spring’s tight-wound end goes first onto a new refill; put on wrongly, a refill sticks or does not extend all the way, Hackaday on the Engineer Guy’s video: readers’ comments on the cam turning the cartridge and on pens with one spring.

The 3D models, drawings and text are our own. The device shown is a generic one of our own design, not any one maker’s model.