Fix it yourself, pay a repair shop, or replace it?
FaultWorn battery
- PartNo sourced figure
- Toolsnot priced
- Time1–2 h
- 3D risk levelHigh
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. We found no fair, sourced figure for this yet, so the card gives no verdict it cannot back. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
11 steps · 11 chapters · 10 screws · screen-first access
Google Pixel 8 battery replacement: interactive 3D teardown
Follow the base Pixel 8 through its front opening. This interactive reconstruction separates the display, thin thermal layers and internal plate before reaching the cell. Pause, orbit or spread the layers to understand what blocks the next action, then reverse the sequence to fit a replacement.
Meet the Pixel 8
Explore the base Pixel 8 from its screen to its battery. This model represents the version without the mmWave antenna cable. Use the X-ray map to locate the layers, then follow eleven animated chapters.
Tools: 3IP Torx Plus driver, Plastic opening pick, Nylon spudger
- Check your exact model before ordering parts. Pixel 8 Pro, Pixel 8a and mmWave-equipped hardware are outside this model’s scope.
Before you open it: the risk map
Before opening: inspect the screen seam, the concealed cable and coil hazards, and the two groups of internal screws. The highlighted boxes are estimated model regions, not measured safe-work boundaries.
No-pry and hidden cable zones
- Pick depth · max 3 mm Bottom screen seam
- Pick depth · max 3 mm Right screen seam
- Pick depth · max 3 mm Top screen seam
- Pick depth · max 3 mm Left seam and display flex
- No metal Battery pouch: never deform
- Hidden cable Power and volume button flex
- No pry Charging coil under the cell
Screw length map
- 3IP · 5 mm ×2
- 3IP · 5.1 mm ×8
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed device.
All 11 steps
- 1Prepare and warm the screen edge
Fully discharge the battery, shut down and unplug the phone. Warm the screen perimeter gently. The animation compresses the heating time; it is not a temperature or duration measurement.
- 2Release the screen perimeter trap
Lift a small gap with the suction handle and work around the softened seam. Keep the pick’s 3 mm mark outside the phone. The left-edge cable and perimeter contacts need room. Avoid this trap: Watch the red pick cross the rim and meet the cable. The shown damage is illustrative; its distance and deformation are not a measured failure threshold.
- 3Support the screen on the left
Raise the screen’s right edge and support it to the left. Its cable is still connected. The foam support in this scene keeps the panel from hanging from that cable.
- 4Disconnect and set aside the screen
Unclip the small connector cover, disconnect the display and transfer the panel to its soft rest. The battery connection is still hidden under the midframe at this point.
- 5Remove the graphite sheet and shim
The dark graphite layer leaves first, followed by the narrow bottom shim. The model separates them visibly so the fasteners below can be identified. A new graphite sheet is required for reassembly.
- 6Remove the USB-C bracket
Remove the bracket’s two 5 mm screws and lift the bracket away. Each screw travels to a numbered well in the tray; retain that location when rebuilding.
- 7Unfasten the midframe
Work through the eight 5.1 mm midframe screws. The driver and highlighted well show which fastener is moving. Keep all eight organised rather than pooling the screws.
- 8Lift the midframe clear
Release the midframe at its lower-right edge and lift it clear of the thermal pad. The battery and its connector are now visible. Check the pad before reusing it.
- 9Disconnect the battery
Disconnect the battery with the nylon tool. Keep the plug separated from its socket while the cell is being removed. The isolated connector is highlighted in this chapter.
- 10Release the battery adhesive trap
Gentle rear warming and a few drops of >90% isopropyl alcohol soften the bond. Allow a minute. Work at the right-hand centre; avoid the upper-right button flex and the coil below. Avoid this trap: The red blade demonstrates a failure, not a removal method. Stop if the cell deforms. Its exaggerated dent makes the load visible and does not predict a safe force.
- 11Lift out the released battery
Transfer the freed cell to its protected rest. The animation leaves the inner frame open for inspection. Select Reassemble to follow the replacement and closing sequence.
Prepare the bench
- Exact replacement battery and consumables · match the base Pixel 8
- Opening tools and soft supports · protect both glass faces
- Screw organisation · keep each fastener in its own position
Questions
Which Pixel does this model cover?
The base Pixel 8 without the mmWave antenna cable. Other Pixel models and the mmWave variant require their own hardware-specific instructions.
Why is the screen removed before the battery is disconnected?
The battery connector is covered by the midframe. This phone’s access sequence differs from phones whose battery connector is available immediately after opening.
Are these exact factory CAD parts?
No. The outside dimensions and cited procedure facts are sourced; the internal geometry is an illustrative reconstruction. It is intended to make the arrangement and order easier to understand.
Does Reassemble mean reusing the removed battery and adhesive?
No. It shows the replacement cell and gives fresh-adhesive and graphite-sheet instructions. Keep damaged or exhausted material separate from the new parts.
Does opening affect water resistance?
Opening disturbs the original seal. Use the correct replacement adhesive, and do not assume the phone retains its original water-resistance rating after repair.
Safety
Fully discharge, power off and unplug before opening. A swollen, damaged, hot or unusually smelling battery needs professional handling. Do not bend, puncture or short a cell. Keep alcohol away from heat and ignition; allow it to evaporate. Protect your eyes and hands from broken glass.
- Lithium-ion batteries: never bend, puncture or pry a battery with metal. A damaged cell can go into thermal runaway: it smokes, catches fire and can explode. Discharge it below 25% first; if it swells, hisses, smokes or gets hot, stop and move it somewhere safe.
- Static (ESD): work on an anti-static mat with a grounded wrist strap; a spark you cannot feel can kill a chip.
- Power off: switch the device off and unplug its charger before you open it, and disconnect the battery before touching anything else inside.
About this teardown
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
This is our own procedural model of the base Google Pixel 8 without the mmWave antenna cable. It uses Google’s published outer size and typical battery capacity. It is not a Pixel 8 Pro or Pixel 8a. The camera bar and two rear camera modules identify the family, but no manufacturer logos or copied screen artwork appear.
The eleven chapters group a longer physical repair into readable 3D scenes. Parts have their own identities, tray positions and layer numbers; their moves are animated, not a recording of hands. Explode is a teaching view, not a route by which the intact phone can physically separate.
Internal outlines, thicknesses, cable routes, connector locations, support positions and hazard boxes are estimates drawn to explain the sourced access order. The display and battery failures are deliberately visible illustrations, not experimentally established force, depth or angle thresholds. Consult the linked repair documents and your actual hardware.
The non-mmWave variant was chosen deliberately. A phone with the additional mmWave cable requires antenna-cable handling before the thermal layers are removed; this extra assembly is not pictured. Do not apply this simplified scene unchanged to that variant.
The current iFixit battery procedure uses softened adhesive rather than a stretch-release-strip demonstration. Google’s manual requests a fully discharged battery; this page adopts that preparation. No screw torque or exact heating temperature has been inferred. Playback time is shortened independently of real repair time.
Sources: Google: Pixel phone hardware specifications, Pixel 8, Google: Pixel 8 Repair Manual v2.0, safety and service structure, Google: Pixel 8 and Pixel 8 Pro safety information, iFixit: Google Pixel 8 Battery Replacement, fasteners and battery access, iFixit: Google Pixel 8 Screen Replacement, opening and display cable, iFixit: Pixel 8 Repair Snapshot, disassembly relationships, iFixit: Apply new screen adhesive to the Pixel 8, iFixit: Apply a new graphite sheet to the Pixel 8, iFixit: Apply new battery adhesive to the Pixel 8.
The 3D models, drawings and text are our own. Google, Pixel and Tensor are trademarks of their owners, named only to say which device this teardown is for; iTakeApart is not affiliated with them.