How a zipper worksZipperMetal zipper

Steps ↓
Concept model Risk: Low ~10 min
How it works · in 3D Metal zipper

Illustrative 3D Concept Model — Generic Layout

🟢 Overall risk: Low ⏱ About 10 min (our estimate) 💰 DIY vs. Shop
Step0/8
Meshed11/22
Slider52%
TravelStill
TapesSplayed
Side pullNone
What is in a zipper8 steps · press play

3D Spatial Reconstruction: a generic model of our own design, built from published facts to show how the parts work together. Real ones differ by maker and model: always check your own before you open or adjust it.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this guide.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itCan it be opened at home?
Overall repair riskLow
Time requiredAbout 10 min (our estimate)
What can go wrongA tooth bent by a forced slider, a slider squeezed too far, or teeth pulled off the tape by an overfilled bag.
Cost comparison DIY: parts and toolsGet the part ↗Get the kit ↗ Tailor or repair shop: varies by shopSearch nearby repair shops ↗Opens local search results in Google Maps
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

FaultStuck or splitting zipper

Your time is worth
Fix it yourselfNo sourced figure
  • PartNo sourced figure
  • Toolsnot priced
  • Time10 min
  • 3D risk levelLow
Repair shopNo sourced figure
New or refurbishedOnly a part is replaced
No verdict: a figure is missingNo sourced price for the part, so no verdict.

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. We found no fair, sourced figure for this yet, so the card gives no verdict it cannot back. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

8 steps · 22 pairs of teeth · a Y channel and a wedge · drawn 6 × life size · 3 traps to avoid

How a zipper works: interactive 3D guide

Illustrative 3D Concept Model — Generic Layout

A metal zipper drawn large in 3D, its slider see-through: two rows of teeth half a pitch apart, a Y-shaped channel that swings each tooth into place, and a wedge that parts them again. Press Zip Up / Down to run the slider yourself, Explode to lift its layers, or Inside the Slider to look straight down the channel.

What is in a zipper

A metal zipper of our own design, drawn about six times life size on a clear tray: two cloth tapes, a row of 22 metal teeth clamped along the edge of each, a slider with a Y-shaped channel and a wedge inside it, a pull to work it by, two top stops and a bottom stop. Press Zip Up / Down to run the slider yourself, at any step.

Before you open it: the risk map

Seen through the slider: the mouth where cloth catches, the plates that take only a tiny squeeze, the teeth’s grip on the tape, and the stops at each end.

Where a zipper gets hurt

What to find first

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed slider.

All 8 steps

  1. 1Two rows, half a tooth apart

    The slider runs down and the two rows lie open. All 44 teeth are the same shape: a rounded nib on the face towards the zipper’s top, and a scoop of the same shape on the face towards its bottom. The rows are set half a pitch apart, so each tooth of one row faces a gap in the other. Closed, they alternate one from each side, and every nib sits in the scoop of the tooth above it, which belongs to the other row.

  2. 2The slider’s Y channel

    Look down through the slider’s clear plates. Its walls form a Y: two arms at the mouth, one for each row, and a single stem at the throat, just wide enough for the closed chain. A row running up an arm has to follow its curve, and it is the curve that matters: the teeth are fixed along the tape, so where the tape bends their heads fan out, and the gap between two teeth grows. In a straight row that gap is too small to let a tooth of the other row past its nib.

  3. 3Closing, tooth by tooth trap

    Pulled up, the slider takes the rows in at its mouth and brings them together in its stem, one tooth at a time, from one side and then the other. Each tooth swings in at the angle the curve gives it, past the tooth above, its nib towards that tooth’s scoop. As the row straightens behind it, the gap closes round it and the nib seats. It is the channel’s shape that sets the angle. Watch the nibs turn cyan as they seat, and the count go up. Avoid this trap: A fold of lining or a loose thread near the tape can be drawn into the mouth with the teeth. The slider stops, and the natural thing is to pull harder. Don’t: a zipper maker warns that forcing a slider that does not run smoothly can damage the teeth, and here the wedged cloth drags one tooth out of line, so that it can no longer seat. Stop, and pull the slider back the way it came, taking the trapped cloth out as it frees. If the slider has bitten deep into the cloth, work it back gently; that takes patience, not force. Which tooth bends, and how far, are our picture.

  4. 4The wedge opens them

    Pulled down, the same slider does the opposite. The closed chain comes in at the throat and meets the point of the wedge, the amber diamond between the arms. The wedge drives the rows apart and sends each one round its arm, so the tape curves and the heads fan open again. With room to move, each nib swings out of its scoop, one at a time, and the tapes splay behind the mouth.

  5. 5Why it holds, and opens only at the slider trap

    Pull the two tapes apart below the slider, and the teeth barely move: the rows take up a little play, then each nib bears on the side of its scoop. To come out, a nib would need some distance from its neighbours, and there is no room for that: the tape does not stretch, and it holds every tooth at its pitch. Only a bend in the tapes makes the room, and the slider is the part that makes the bend. So the slider runs back down, and the wedge opens the chain where the sideways pull could not. Avoid this trap: The chain holds, but a tooth holds on to the tape only by its jaws. Care advice for zippers says never to force one closed on an overfilled bag, and a zipper maker’s manual describes teeth pulled out of place or off the tape once a sideways pull is more than their grip can take. Once a tooth has gone, its neighbours have room to come loose, and the rows part round the gap, however good the slider is. Pull the two sides together by hand before you close it, or take something out. A new slider will not mend this: with teeth gone, a zipper needs replacing. Which tooth goes, how the tapes part and how far they part are our picture.

  6. 6The stops

    Run up as far as it will go, the slider’s mouth comes against the two top stops, clamped on the tapes above the last teeth, and they keep it from running off the end. There the wedge is still between the rows, so the last few teeth stay parted: no zipper is ever quite closed at the top. Run down, its throat meets the bottom stop, which clamps both tapes together under the first teeth, so the rows can part no further and the slider stays on.

  7. 7What wears: the slider lets go

    Most often, a zipper that will not stay shut has a worn or bent slider. Long or rough use bends a slider or spreads it, and its plates no longer press the teeth together firmly enough to interlock them. Here its plates are shown sprung open at the throat, far more than a real one would be. With that much room, the rows ride past each other in the stem instead of seating. They come out unmeshed, the tapes pull them apart, and the chain splits behind the slider while it is still going up.

  8. 8The fix: a very small squeeze trap

    A slider that has only sprung can often be brought back. Set a small pair of locking pliers so that they just close on the plates, and clamp the slider only, not its pull or the cloth. Squeeze one side, then the other at the same setting; tighten the setting by about a sixteenth of a turn and repeat only if it needs it. Then run the slider down past the split and back up: the rows seat again and it holds. Avoid this trap: The squeeze is a tiny one, and it is easy to overdo: the plates close on the teeth and the slider becomes hard to pull or will not move at all. Go up a very little at a time, and try the slider after each squeeze. If you have gone too far, a thin flat screwdriver worked gently into the gap on each side of the slider can open it a little again. A slider that does not hold after a few tries wants replacing, not more force. How far the plates close is drawn large here.

What is in it

Questions

How does a zipper work?

Two rows of teeth on two tapes, half a tooth apart, and a slider with a Y-shaped channel. Pulled up, the channel curves each row so that its teeth fan open, swings them together one at a time and lets each nib seat in the scoop above it. Pulled down, a wedge in the slider drives the rows apart again.

Why doesn’t a zipper come apart when you pull it sideways?

Because each nib sits in a scoop and bears on its side, and to come out it would have to move along the chain, where the tape leaves it no room. Only a bend in the tapes makes that room, and the slider is what makes the bend.

Why does my zipper split open behind the slider?

Most often the slider is worn or has spread, so it no longer presses the teeth together firmly enough. A very small squeeze with locking pliers can bring it back; if that does not hold, it wants a new slider. If teeth are missing or the tape is torn, the zipper needs replacing.

How do I free a zipper stuck on fabric?

Stop pulling. Pull the slider back the way it came and take the trapped cloth or thread out. If it has bitten deep into the cloth, work it back gently. A forced slider can damage the teeth.

What do you do with a zipper that is hard to move?

Don’t force it. A zipper maker’s advice is paraffin on the front and back of the teeth, then work the slider up and down.

Is a zipper ever fully closed?

Not quite: at the top stops the wedge is still between the rows, so the last few teeth stay parted. Here, 19 of the 22 pairs are meshed at the top.

Can I close a zipper without the slider?

Not by pressing the rows together. In a straight row, the gap between two teeth is too small to let a tooth of the other row past its nib; it takes the curve that the slider’s channel gives the tape.

Safety

Nothing here is dangerous, but a zipper can bite: keep skin and thread clear of the slider’s mouth, and keep your fingers off the pliers’ jaws.

About this guide

3D Spatial Reconstruction: a generic model of our own design, built from published facts to show how the parts work together. Real ones differ by maker and model: always check your own before you open or adjust it.

The zipper is a generic one of our own design, not any maker’s, and it is drawn about six times life size: its closed chain is 30 mm across, where a size 5 zipper’s teeth are about 5 mm. It has 22 teeth a row. Every figure on the page is a count or a proportion of the model; the slider’s percentage is how far along its own travel it is.

Each tooth here is a simple metal piece with a nib on the face towards the zipper’s top and a scoop on the face towards its bottom, the arrangement Gideon Sundback patented in 1917: identical teeth, a projection on one side and a recess on the other, alternating from the two tapes and nesting one in the next. The sources say “top” and “bottom”, or “one side” and “the opposite side”; we read those as the faces along the chain, so that here the nib and the scoop show from above. Real teeth are smaller and more rounded, and their exact shape varies by maker.

The teeth, the tapes and the slider’s channel are worked out from one curve: the way a row bends in the channel. So what you see fan open, swing in and seat is what that curve does at every slider position, with nothing passing through anything. The curve’s exact shape and the slider’s proportions are ours.

The plates sprung open in step 7, the way the rows then ride past each other, and how far they part are our picture, drawn far larger than a real slider’s wear. So are the pliers’ closing, the bent tooth in the cloth trap, and which tooth goes in the overfilled-bag trap. The tray is only there to hold the zipper for the picture. The time on the scorecard is our own estimate, and we give no prices: what a shop charges varies too much for a fair figure.

Sources: Wikipedia: Zipper (teeth and tape, the Y-shaped channel, top and bottom stops; a worn or bent slider that cannot press the teeth together is the most common failure), US patent 1,219,881, Gideon Sundback, Separable Fastener, 1917 (identical members, a projection on one side and a recess on the other, alternating from the two stringers), Veritasium, Making a giant zipper, its transcript (the nib and the scoop; the channel sets the teeth’s angle; a tooth needs room from its neighbours to come out, and the tape does not stretch; the wedge is always there, so no zipper is ever quite closed at the top; a lost tooth lets its neighbours come loose), YKK Americas, zipper FAQs (forcing a slider that does not run smoothly can damage the teeth; paraffin on the front and back of the teeth), iFixit, Repairing a zipper slider (separating just behind the slider; locking pliers on both sides at the same setting, a sixteenth to an eighth of a turn at a time; clamp the slider only; overdone, it gets hard to zip, and a thin screwdriver opens the gaps again), iFixit, Coil zipper diagnosis (a loose slider will not keep the teeth together; a compacted one is hard to pull; damaged teeth or torn tape mean replacing the whole zipper), Maxpedition, care instructions for its YKK zippers (do not forcibly close a zipper on an overfilled bag; a slider caught on thread or cloth is pulled back, not forced, and worked back gently if it has bitten deep), YKK Zipper Usage Instruction Manual, element breakage (teeth pulled sideways against the slider wall, displaced or detached once the force exceeded their attachment strength), Hex, extending the life of a bag (forcing an overfull bag closed strains the teeth, slider and seam; pull the two sides together by hand, then draw the slider up gently), VAUDE, Replacing a zip slider (frequent or improper use can bend or expand a slider so the teeth no longer zip together), WAWAK, Zipper size chart (the size number is about the teeth’s width in millimetres).

The 3D models, drawings and text are our own. The device shown is a generic one of our own design, not any one maker’s model.