Fix it yourself, pay a repair shop, or replace it?
- Part$70–$76.99
- Toolsnot priced
- Time1–2 h
- 3D risk levelMedium
Appliance technician
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
8 steps · 2 traps to avoid · Front access, drum stays in · Samsung DV42H electric dryers
Samsung Dryer Not Heating: Element, Thermal Fuse and Thermostats: interactive 3D teardown
When a Samsung DV42H electric dryer turns but blows cold, check the breaker first: one leg of its 240 V supply can trip on its own. If that is not it, the heater’s circuit holds three parts to test, the 160 °C thermal cut-off, the 127/99 °C hi-limit and the 5300 W element, and on this family all of them come out through the front once the top cover, the console and the front panel are off. The drum, the belt and the idler stay where they are.
What you need
A Samsung DV42H electric dryer that turns but stays cold has three things in its heater circuit to test: the 160 °C thermal cut-off, the 127/99 °C hi-limit and the element itself. On this family they all come out through the front: off come the top cover, the console and the front panel, and the heater duct assembly slides out low on the right with the drum left in. Before any of it, look at the breaker: one leg of the 240 V supply can trip on its own, and the dryer then spins but stays cold.
Tools: Phillips #2 screwdriver, Digital multimeter (Ω), Needle-nose pliers
- Samsung’s technical sheet is written for technicians and says to disconnect the power before servicing unless a test needs it: every test here is done unplugged, with a meter.
Which Samsung DV42H dryers this fits, and the parts paired with them
Samsung DV42H electric dryer heater parts
Match your model number exactly: only the part numbers a parts page pairs with a model are listed, and the element must be the single-heater kind.
| Samsung model | Heater | Element | Cut-off fuse | Note |
|---|---|---|---|---|
DV42H5000EW/A3 | Single, 5300 W | DC47-00019A | Not listed | The 3D |
DV42H5200EW/A3 | Single, 5300 W | DC47-00019A | DC47-00015A | Same wiring |
DV45H7000EW/A2 | Not on the sheet | DC47-00019A | DC47-00015A | iFixit’s list |
DV42H5600E, DV45H6300E | Dual, 3700 + 1500 W | Another part | — | 13 Ω, 34 Ω |
No matching series found. Clear the filter to view all compatible models.
Readings (Samsung’s sheet): a single heater about 10 Ω between pins 1 and 3; a dual one 13 Ω (pins 2–3) and 34 Ω (pins 1–2); the cut-off and the hi-limit each under 1 Ω; the thermistor 10 kΩ at 25 °C. The DV42H5400 electric shares the DV42H5000’s wiring diagram, but no parts page we read pairs it with these numbers. Gas models have no element.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the closed cabinet: the 240 V outlet behind it, the screws and hooks that hold the top cover, the console and the front panel, the lint duct below the door, and the heater low on the right with its terminals and coil.
240 V, lint, terminal and sheet-metal zones
- Live 240 V 240 V cord: unplug it, breaker off
- Overheats Lint duct: clear it before new parts
- No force Heater terminals: no force on them
- Sharp sheet metal Sheet-metal edges: wear gloves
Screw and clip map (no screw length is published)
- Console guide panel · 2 Phillips ×2
- Console hook (6) ×6
- Door opening · 2 Phillips ×2
- Front panel tab (3) ×3
- Heater · 1 Phillips
- Plate (U) · 4 Phillips ×4
- Top cover · 2 Phillips ×2
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed dryer cabinet.
All 8 steps
- 1Unplug the 240 V cord and switch the breaker off trap
Pull the dryer’s plug out of its 240 V outlet and switch its two-pole breaker off. Do not take “it will not heat” to mean “it is dead”: Samsung warns that one of the supply’s two circuits can trip on its own, and the dryer still turns on and spins, so its motor and controls are still fed. Avoid this trap: The drum still turns and the heater stays cold, so it is easy to think the power is off. Samsung says only one of the two circuits may have tripped, and the dryer will then turn on and spin but not heat. Start undoing screws with the plug in, and the wiring under the top cover is still live.
- 2Take out the two top rear screws and slide the top cover off
Take out the two Phillips screws along the top’s back edge. Slide the top cover back a few centimetres, off its front hold, and lift it away. Set it where it cannot be scratched or knocked, as Samsung asks.
- 3Free the console from its hooks and rest it on top
Take out the two screws that hold the console’s guide panel, release its six hooks and lift the console off. Samsung’s chapter unplugs its connector housings and takes it away; the AppliancePartsPros video lifts the locking tabs along its back, tips it forward and rests it on top with its wires still connected, which is what the 3D shows. Mind its face: Samsung asks you not to scratch it.
- 4Take off the front panel and unplug the door switch
Open the door and take out the two screws at the bottom of the door opening, which hold the panel to the lint screen housing. Close the door and take out the four screws along the top front plate, Plate (U). Pull the panel forward, unplug the door switch’s connector, which has no locking tab, then lift the panel off the three tabs along its bottom.
- 5Clear the lint screen housing before anything new goes in trap
With the front panel off, lift the lint screen out and brush the housing below it clear of packed lint, then clean the exhaust duct behind the dryer as well. Restricted exhaust and a lint-clogged machine overheat the dryer and trip its safety devices (iFixit), and Samsung says its overheating codes are commonly a clogged lint screen or vent, so a new cut-off or element fitted without this meets the same heat. Avoid this trap: A blown cut-off is a symptom: iFixit puts it down to restricted exhaust or a lint-clogged machine, and Samsung’s overheating codes are commonly a clogged lint screen or vent. Leave the duct packed and the new part meets the same heat.
- 6Unplug the heater and slide it out through the front
Unplug the moisture sensor’s connector, then pull the heater’s six terminal housings off by the housings themselves: Samsung warns against forcing the terminals. Take out the heater’s screw; Samsung’s chapter lists one, the video’s dryer had three, so take out every screw that holds it. Free the lower bracket’s tabs, lower the assembly, ease it out of the duct at the back and guide it out through the front opening, its harness clear below the lint duct.
- 7Test the element and both thermostats with a meter
On the bench, set the meter to ohms. Samsung’s sheet gives the single heater about 10 Ω between pins 1 and 3, and the thermal cut-off and the hi-limit each under 1 Ω. An infinite reading on any of them means that part is open and must be replaced. Here the element reads open: its coil has broken.
- 8Take the old element out of its housing
Take out the two screws of each thermostat, four in all as Samsung counts them, and lift both off. Bend each element terminal’s tab flat and push the terminals back through the ceramic block. Take out the housing’s screws (iFixit counts about six), part the two halves and lift the old element out.
What you need
- A Phillips #2 screwdriver and needle-nose pliers · for every screw on this route and the element’s terminal tabs
- A digital multimeter on ohms · about 10 Ω across the element, under 1 Ω across each thermostat
- Work gloves and a dryer vent brush · for the sharp sheet metal, the new coil and the lint duct
Questions
Why does my Samsung dryer spin but not heat?
An electric Samsung dryer needs a 240 V outlet, and Samsung says one of its two circuits can trip on its own: the dryer then turns on and spins but does not heat. Reset the breaker, off for 30 seconds and then on. Low voltage can also leave the panel and the motor working with no heat, and Eco Dry lowers the heat on purpose. If none of that is it, test the thermal cut-off, the hi-limit and the element.
What does HE mean on a Samsung dryer?
Samsung’s DV42H/DV45H technical sheet defines HE as an invalid heating temperature while the dryer runs, and says to call for service. In its Smart Install self-test, HE means the motor or the heater is not working normally. Samsung Canada lists hE with HC as overheating codes, commonly a clogged lint screen or vent.
What should a Samsung dryer heating element read on a multimeter?
With the dryer unplugged, Samsung’s sheet gives a single heater about 10 Ω between pins 1 and 3, and a dual heater 13 Ω between pins 2 and 3 and 34 Ω between pins 1 and 2. The thermal cut-off and the hi-limit each read under 1 Ω, and the thermistor 10 kΩ at 25 °C. An infinite reading means that part is open: replace it.
Do I have to take the drum out to change the heater?
Not on the DV42H. Samsung’s chapter takes off only the top cover, the console and the front panel before the heater comes out, and the AppliancePartsPros video slides the heater duct assembly out of its rear duct and out through the front opening, leaving the drum, the belt and the idler alone.
Why did my Samsung dryer’s thermal fuse blow?
Restricted exhaust or a lint-clogged machine overheats the dryer and trips its safety devices, iFixit says, and Samsung names a clogged lint screen or vent as the common cause of its overheating codes. Clear the lint duct and the vent before the new part goes in, clean the vent once or twice a year, and use no plastic or foil duct. If the cut-off blew, iFixit advises replacing the hi-limit too.
Is it worth fixing, or should I buy a new dryer?
Fixr puts a technician’s heating element job at $150 to $350 and a new dryer at $600 to $1,500; Abt sells Samsung’s current 7.2 cu. ft. DVE45T3200W/A3 for $529. Fixr’s own rule of thumb is to replace a dryer that is past half its 8 to 12 years when the repair costs about half the new price. The element itself is $70 to $76.99.
Safety
Unplug the 240 V cord and switch the breaker off before you take out a single screw: a dryer that spins but does not heat can have one leg of its supply still live. Wear gloves: the sheet-metal edges are sharp, and skin oils on the new coil shorten its life.
- Mains power: switch it off and unplug it before you open it: its power supply runs on mains voltage. Never plug it in with a cover off.
- Static (ESD): work on an anti-static mat with a grounded wrist strap; a spark you cannot feel can kill a chip.
About this teardown
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
This guide models the Samsung DV42H5000EW/A3, the base electric model of the DV42H family, whose wiring diagram Samsung shares with the DV42H5200 and DV42H5400. The steps follow Samsung’s DV42H disassembly chapter and its technical information sheet DC68-03382A, with the hands-on detail of an AppliancePartsPros video. The real dryer differs from the brief this guide began from: the heater comes out through the front once the top cover, the console and the front panel are off, so the drum, the belt and the idler are never touched and nothing is reached through the back panel; and the DV42H5000, 5200 and 5400 have a single 240 V 5300 W heater, where the DV45H6300E and DV42H5600E on the same sheet have a dual 3700 W + 1500 W one.
There are three thermal devices, not two: the 160 °C, 25 A thermal cut-off (Thermostat 3) and the 127/99 °C, 25 A hi-limit (Thermostat 2) on the heater housing, and an 85 °C, 25 A cut-off (Thermostat 1) on the blower duct beside the thermistor. Thermostat 1 is in the motor’s circuit, so when it opens the dryer will not run at all. The heater only gets power while the motor runs: its circuit goes on through the motor’s centrifugal switch, which iFixit says can block heat when it fails. HE on the display is not a heater code as such: Samsung’s sheet defines it as an invalid heating temperature, its self-test shows it when the motor or the heater is not working normally, and Samsung Canada groups hE with the overheating codes, commonly a clogged lint screen or vent.
Samsung publishes no cabinet size for the DV42H on any page we could load, so the 3D uses its 27-inch electric siblings’ 686 × 984 × 800 mm (27 × 38¾ × about 31½ in) as an estimate, and stands it on the workbench beside the mat, where the small parts are worked on. The heater housing’s size, where each part sits inside, the lint duct’s shape and every screw’s place are our estimates, and no source gives a screw length, so none is shown. Samsung’s chapter takes one screw out of the heater, where the video’s dryer had three; iFixit counts about six housing screws on the model it shows. The time and the multimeter’s on-screen readings are ours.
Part numbers are only those a parts page we read pairs with this model: iFixit lists the genuine DC47-00019A element for the DV42H5000EW/A3 and DV42H5200EW/A3, and the DC47-00015A thermal cut-off fuse (320 °F, Samsung’s 160 °C) for the DV42H5200EW/A3 but not the DV42H5000EW, so check your model’s own parts list. iFixit also sells DC47-00016A, a thermal cut-off thermostat it lists for the DV42H5000EW/A3-01 and for gas dryers too, so it is not the heater box’s fuse; no page we read gives its rating or where it sits. No page we could load pairs a hi-limit or a thermistor part number with this model, so neither is named. Abt’s $529 is for the DVE45T3200W/A3, a current 7.2 cu. ft. Samsung electric dryer that is comparable, not the same model.
Sources: Samsung Clothes Dryer Technical Information DC68-03382A (DV45H/DV42H): error codes, Smart Install test, heater ohms, thermostat ratings, wiring diagrams, Samsung DV42H Disassembly and Reassembly chapter (top cover, console, frame panel, heater; text preview), AppliancePartsPros: Samsung dryer heating element replacement video DC47-00019A (front panel route), Samsung US: Clothes are not dry after using a Samsung dryer (240 V, one circuit tripped, vent rules), Samsung Canada: dryer error codes (HC, hE overheating), iFixit: Samsung Dryer Not Heating (breaker pole, vent, cut-off and hi-limit, centrifugal switch), iFixit: Samsung Front Load Dryer Heating Element Replacement (housing screws, gloves, terminal tabs), iFixit: Samsung Front Load Dryer Disassembly (heater on the right side), iFixit: Samsung DVE47CG3500W Thermal Fuse Replacement (240 V unplugged, breaker off, gloves), Price: iFixit, genuine Samsung DC47-00019A dryer heating element, $76.99, out of stock (fits DV42H5000EW/A3, DV42H5200EW/A3; read November 2026), Price: Parts Town, Samsung DC47-00019A heating element, $70.00 list (read November 2026), Price: iFixit, genuine Samsung DC47-00015A thermal cut-off fuse, 320 °F, $42.99 (fits DV42H5200EW/A3; read November 2026), iFixit: Samsung DC47-00016A thermal cut-off thermostat (fits DV42H5000EW/A3-01 and gas models), Samsung DVE45R6100C/W spec sheet (27 × 38¾ × 31½ in, used as the estimate of the cabinet), Price: Fixr dryer repair cost guide, heating element $150–$350, thermostat $100–$260 (read November 2026), Price: Abt, Samsung DVE45T3200W/A3 7.2 cu. ft. electric dryer, $529 (read November 2026).
The 3D models, drawings and text are our own. Samsung is a trademark of its owner, named only to say which device this teardown is for; iTakeApart is not affiliated with it.