Fix it yourself, pay a repair shop, or replace it?
- Part$14.99
- Toolsnot priced
- Time20–45 min
- 3D risk levelMedium
Appliance technician
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
5 steps · 2 traps to avoid · Genuine OEM WP3392519 & 279838 · Rear-access 29-inch electric dryers
Whirlpool & Kenmore Electric Dryer Thermal Fuse & Heating Element Replacement: interactive 3D teardown
When a 29-inch Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, or Amana electric dryer with a top-mounted lint screen refuses to start at all, a blown WP3392519 thermal fuse on the rear blower housing is the #1 culprit; when it tumbles normally with cold air, an open or grounded 279838 heating element (~9–10 Ω) inside the right rear canister is usually to blame. Inspect the entire rear bay, multimeter checks, and exhaust-lint trap in 3D before picking up a 1/4-inch nut driver.
What you need
On 29-inch Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, and Amana electric dryers with the lint screen on the top console, both no-start and no-heat faults sit behind the rear sheet-metal access panel. On the left blower housing sits the white WP3392519 single-blow thermal fuse (wired in series with the drive motor on electric models, so a blown fuse leaves the dryer completely dead); on the right vertical heater canister sits the 279838 240 V 5400 W nichrome heating element (~9–10 Ω).
Tools: 1/4-inch hex nut driver, Digital multimeter (Ω / continuity), Needle-nose pliers
- Always pull the 240 V dryer power cord out of the wall outlet before touching a single rear panel screw—an electric dryer carries two live 120 V legs even when turned off.
Exact OEM Part Numbers, Brand Cross-Reference & Multimeter Specs
Whirlpool / Kenmore Rear-Access Electric Dryer Thermal Fuse & Heating Element Reference
Confirm your dryer has a 240 V electric cord and the lint screen sliding out of the top panel (front-filter 27-inch Duet / Cabrio models open from the front toe-panel instead). Match your symptom, OEM number, and ohmmeter spec below:
| Component / Series | Symptom When Failed | Genuine OEM & Cross-Ref # | Mounting & Fasteners | Multimeter / Spec |
|---|---|---|---|---|
Blower Housing Thermal Fuse (196 °F / 91 °C non-resettable) | Dryer will not start when Push-to-Start is pressed (electric models wire fuse in motor circuit) | WP3392519 (replaces 3392519, 3388651, 694511, 80005, AP6008325) | Left rear blower housing · 1 × 1/4 in hex screw + bottom hook slot · two 1/4 in spades | < 1 Ω (0–2 Ω continuity) with one lead unplugged; OL = blown |
Electric Dryer Heating Element (240 V, 5400 W coil frame) | Drum tumbles with cold air (open coil) or heats continuously even on Air Fluff (coil sagged to case) | 279838 (replaces 279837, 2438, 3398064, 3403585, 8565582, W10724237, AP3094254) | Right vertical heater canister (267 × 191 × 51 mm assembly) · 2 × 1/4 in hex screws · 5/16 in spades | ~9–10 Ω terminal-to-terminal AND OL from each terminal to bare steel canister |
Whirlpool (WED4815EW, WED4950HW, LER, LET, LE) & Kenmore 110.6... | No start (WP3392519) or tumbles cold (279838 / 279816 cut-off kit) | WP3392519 fuse + 279838 element | Full rear galvanized sheet-metal panel (8–10 × 1/4 in hex screws) | 240 V AC · 4 in (102 mm) rear exhaust duct |
Maytag (MEDC300 / MEDC465), Roper (RED / AED), Amana (NED4655EW) & Estate (EED) | No start (WP3392519) or tumbles cold (279838) | WP3392519 fuse + 279838 element | Full rear galvanized sheet-metal panel (8–10 × 1/4 in hex screws) | 240 V AC · 5400 W heater circuit |
No matching series found. Clear the filter to view all compatible models.
Gas Dryer Difference: Gas Whirlpool/Kenmore dryers (WGD / 110.7...) also use thermal fuse WP3392519 on the blower housing, but wire it into the gas burner circuit (so a gas dryer still tumbles with no heat when WP3392519 blows) and use a glow-bar igniter instead of electric coil 279838.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the rear steel panel: the 240 V terminal block at top center, the left blower housing with the white WP3392519 thermal fuse and lint-choked 102 mm exhaust spout, the right vertical canister housing the 279838 nichrome coil element, and all eleven 1/4-inch (6.35 × 12.7 mm) hex screws.
240 V shock, sharp sheet metal, lint overheat & coil ground zones
- 240 V live 240 V cord & terminal block: unplug from wall before removing rear screws
- Sharp steel Stamped galvanized rear panel edges: wear cut-resistant gloves
- Lint fire / blow 102 mm blower exhaust spout: clean packed lint or new fuse blows again
- Ground short 279838 nichrome coil: verify ~9–10 Ω & zero continuity to steel canister
Screw map (11 × 1/4-inch · 12.7 mm hex sheet-metal screws)
- 1/4-inch hex · 12.7 mm (279838 heating element) ×2
- 1/4-inch hex · 12.7 mm (rear access panel) ×8
- 1/4-inch hex · 12.7 mm (WP3392519 thermal fuse)
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed rear dryer panel.
All 5 steps
- 1Unplug the 240 V cord & unbolt the 8 rear access panel screws
Pull the heavy 240 V dryer plug straight out of the wall outlet so both L1 and L2 hot legs are dead. Put on cut-resistant work gloves, use a 1/4-inch (6.35 mm) hex nut driver to remove the 8 × 12.7 mm sheet-metal screws around the perimeter of the rear access panel, tilt the top edge back, and lift the stamped steel panel clear of its lower slots.
- 2Isolate one wire & test the WP3392519 thermal fuse for continuity trap
Locate the white elongated WP3392519 thermal fuse (91 °C / 196 °F) on the left blower housing beside the cycling thermostat. Grip the metal spade connector—never the light-blue wire insulation—with needle-nose pliers and slide one lead off to isolate the component. Set your digital multimeter to Ω / continuity and probe across both brass fuse tabs: a good fuse reads under 1 Ω (0–2 Ω), while OL (open circuit) proves the fuse has blown. Avoid this trap: WP3392519 is a one-shot safety limiter, not a wear item—it almost always blows because a lint clog, crushed transition hose, or stuck exterior damper blocked exhaust airflow. Bolting in a fresh fuse while grey lint still chokes the 102 mm blower outlet overheats the housing and pops the new fuse right back to OL.
- 3Unscrew the WP3392519 thermal fuse & brush lint out of the exhaust duct
Pull the second spade lead off the WP3392519 thermal fuse, undo its single 1/4-inch (6.35 × 12.7 mm) mounting screw, tilt the top ear out, and slide the bottom plastic hook tab up and out of the blower housing slot. Run a rotary dryer vent brush and vacuum nozzle deep into the 4-inch (102 mm) blower exhaust pipe and top lint chute to clear every clump of packed lint.
- 4Test the 279838 heating element for ~9–10 Ω & coil-to-canister shorts trap
Move to the vertical galvanized heater canister on the right. Pull one heavy red 5/16-inch (7.9 mm) spade connector off the lower ceramic terminal block of the 279838 heating element. Measure resistance across the two heater terminals: a healthy 240 V 5400 W coil reads ~9–10 Ω, whereas OL confirms a broken coil. Next, touch one probe to a heater terminal and the other to the bare steel canister—it must read OL (zero continuity to ground). Avoid this trap: Yanking on the red wire instead of the metal 5/16-inch spade terminal loosens the crimp so high-current 22.5 A draw chars the insulation. Worse, if a warped nichrome coil sags against the steel canister, it passes a basic terminal-to-terminal check yet energized heat runs uncontrolled on Air Fluff until the high-limit cut-off blows.
- 5Unbolt the 2 flange screws & slide the 279838 heating element out
Pull the second red wire off the 279838 terminal block and use the 1/4-inch nut driver to remove the 2 × 12.7 mm hex screws securing the left and right ears of the heater mounting plate. Roll the bottom of the terminal flange slightly outward to clear the canister lip, then slide the 267 × 191 × 51 mm nichrome coil frame straight down and out without snagging its white ceramic insulators.
What you need
- 1/4-inch (6.35 mm) hex nut driver & needle-nose pliers · for the rear access panel screws, fuse/heater screws, and spade connectors
- Digital multimeter with continuity / Ω mode · to confirm < 1 Ω on WP3392519 and ~9–10 Ω (plus ground isolation) on 279838
- Dryer vent brush, vacuum & work gloves · to clear lint from the 102 mm blower duct and protect hands on stamped sheet metal
Questions
Why does a blown WP3392519 thermal fuse keep an electric Whirlpool or Kenmore dryer from starting?
On Whirlpool-built electric dryers, the WP3392519 thermal fuse on the blower housing is wired directly in series with the drive motor return circuit so the machine cannot run at all after overheating past 196 °F (91 °C). On gas models, the same fuse sits in the burner circuit, so the drum still tumbles without heat.
What resistance (ohms) should a good 279838 dryer heating element read?
With the dryer unplugged and at least one red wire pulled off the heater to isolate it, a healthy 240 V, 5400 W 279838 heating element reads roughly 9 to 10 Ω across its two spade terminals. Also test from each terminal to the bare metal heater canister—any continuity means the coil has sagged against ground and must be replaced.
Why did my new WP3392519 thermal fuse blow again after a few loads?
Almost every repeat WP3392519 failure is caused by restricted exhaust airflow—lint packed inside the blower housing, a kinked foil transition hose behind the dryer, or a clogged wall duct and exterior hood damper—or by a grounded 279838 heating element coil staying hot after the thermostat cycles off.
How do I know if my Whirlpool or Kenmore dryer uses rear-panel access?
Pull out your lint screen: if the lint filter slides out of the top console near the right rear corner (common on 29-inch WED, LER, Kenmore 110.6, Roper RED, Maytag MEDC, and Amana NED dryers), both WP3392519 and 279838 are accessed directly through the rear sheet-metal panel.
Safety
Disconnect the 240 V power cord completely before removing any panel screw—never rely on the control knob being off. Never jumper or bypass a blown WP3392519 thermal fuse or thermal cut-off, as doing so disables overheat fire protection.
- Mains power and hot water: unplug the machine and let it cool before you open it: inside are mains wiring and a heater that stays hot long after use. Never run it with a panel off.
- Hot parts and fumes: brakes, exhausts and engines stay hot long after a drive, and a running engine fills a closed garage with carbon monoxide: let parts cool, and keep the door open.
About this teardown
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
This 3D repair guide models the classic 29-inch Whirlpool-built rear-access electric dryer platform shared across Whirlpool (WED, LER, LET), Kenmore 110-series, Maytag (MEDC), Roper (RED/AED), Amana (NED), and Estate—distinguished by its slide-out lint screen on the top panel and full-height galvanized rear access panel.
All diagnostic figures match Whirlpool Service Tech Sheet W10417013C and OEM catalog specifications: genuine thermal fuse WP3392519 ($14.99 OEM on iFixit; $3.25 aftermarket 3392519) opens permanently at 196 °F (91 °C) and tests below 1 Ω when intact, while genuine heating element 279838 ($52.99 OEM on iFixit; $27.25 aftermarket, 240 V 5400 W, 10.5 × 7.5 × 2 in / 267 × 191 × 51 mm) measures ~9–10 Ω across its 5/16-inch spade terminals with OL isolation to the steel canister. Fixr places professional thermostat/thermal-sensor repair at $100–$260, heating-element repair at $150–$250, and full dryer replacement at $600–$1,500 ($620 MSRP for a new 7.0 cu. ft. Whirlpool WED4815EW).
Sources: Whirlpool Dryer Service Tech Sheet W10417013C: Test #3 Heater (~10 Ω across heater circuit), Test #3b Thermal Fuse continuity (electric dryer wired in motor circuit), and Test #3c Thermal Cut-Off, iFixit Repair Guide: Whirlpool Dryer Thermal Fuse Testing and Replacement (unplug 240 V cord, 1/4-inch rear panel hex screws, disconnect one lead, continuity test, clean exhaust vent), iFixit Repair Guide: Roper / Whirlpool Dryer Heating Element 279838 Replacement (two 1/4-inch heater mounting screws, roll bottom out & slide downward, coil-to-housing ground continuity check), Price: iFixit Store, Genuine Whirlpool WP3392519 Dryer Thermal Fuse, $14.99 (replaces 3388651, 3392519, 694511, 80005, AP6008325; read 10 November 2026), Price: iFixit Store, Genuine Whirlpool 279838 Dryer Heating Element, $52.99 (10.5 × 7.5 × 2 in; replaces 2438, 279837, 3398064, 3403585, 8565582, AP3094254, W10724237; read 10 November 2026), Speedy Appliance Parts: 3392519 thermal fuse (196 °F single-blow limiter, $3.25 aftermarket) & 279838 heating element (240 V 5400 W, 5/16 in terminals, $27.25 aftermarket; read 10 November 2026), Price: Fixr Dryer Repair Cost Guide, thermostat/sensor replacement $100–$260, heating element repair $150–$250, new dryer replacement $600–$1,500 (read 10 November 2026), Price: Whirlpool US, new 7.0 cu. ft. Electric Dryer WED4815EW, $620 list (read 11 November 2026).
The 3D models, drawings and text are our own. Whirlpool, Kenmore, Maytag, Roper, Estate, Amana and iFixit are trademarks of their owners, named only to say which device this teardown is for; iTakeApart is not affiliated with them.