Fix it yourself, pay a repair shop, or replace it?
- Part$0
- Toolsnone needed
- Time15–30 min
- 3D risk levelMedium
Appliance technician
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
8 steps · 2 traps to avoid · Bosch 24-inch built-in · E:24 and E:25
Bosch Dishwasher Not Draining: Filter, Pump Cover, Check Valve and Drain Pump: interactive 3D teardown
A Bosch dishwasher that leaves water in the tub, or stops with E:24 or E:25, is usually blocked somewhere in its drain long before its pump is worn out: BSH’s own bulletin names debris in the drain system as the most likely cause and says many drain pumps are replaced unnecessarily. See the whole drain in 3D before you open it: the three filters, the grey pump cover that has to click back in, the impeller, the house side with its high loop, then the check valve and the drain pump.
What you need
On Bosch’s 24-inch built-in dishwashers of the 2015–2022 platform (BSH’s repair manual calls it GV640), waste water leaves through three filters in the tub floor, then past a drain pump cover in the sump, through the drain pump under it, a check valve in the sump’s outlet and the drain hose with its high loop. Steps 1 to 5 are the owner’s clean-out from Bosch’s own manuals; steps 6 to 8 are the repair manual’s technician work at the base.
Tools: Spoon, Needle-nose pliers, Bit driver: #2 Phillips and T20 Torx, Small flat-blade screwdriver, Multimeter
- BSH’s own bulletin: many drain pumps are replaced unnecessarily, and debris in the drain system is the most likely cause. Clean first, replace last.
Part numbers by model
Bosch dishwasher drain parts and the models their pages list
Only the pairings a parts page states. Part numbers vary by model, so confirm yours on Bosch’s spare parts lookup before you buy.
| Part | Bosch’s name | Part number | Listed for | Bosch US list |
|---|---|---|---|---|
| Drain pump cover | Lid, drain pump cover, gray with white handle | 00611322 (replaces 00628305) | Ascenta (BSH bulletin) | $18.50 |
| Check valve | Valve-non return | 00611320 | SHE53T5, SHE65T5, SHX3AR5 | $17.99 |
| Drain pump | Drain Pump BLDC | 00620774 | SHE53T56UC/02, SHE68T55UC/03, SHE9PT55UC/B4 | $66.50 |
| Drain pump | Pump-drain | 00631200 | SHE33T56UC/09, SHE7PT55UC/09, SGE53U52UC/98 | $38.50 |
| Drain pump | Drain Pump 3-Phase | 00611332 | SHE3ARF2UC/08, SHX3AR75UC/07, SHX3AR75UC/14 | $55.50 |
| Coarse and micro filter | Coarse Filter & Micro-Filter | 00645038 (replaces 00651097) | SHE89PW55N/10, SHE7PT52UC/01, SPX68B55UC/07 | $35.99 |
| Coarse and micro filter | Coarse Filter & Micro-Filter | 00615079 | SHU5304UC/06, SHX45P06UC/53 | $50.99 |
No matching series found. Clear the filter to view all compatible models.
Not a check valve: Bosch’s store names part 00611618 “Stop”; the check valve is 00611320. No page we could load pairs the current 300 Series SHE53C85N with its pump, cover or valve numbers.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the tub floor and the base: the filters over the sump, the drain pump cover and the suction cap at its bottom, the drain pump and the check valve under it, the toe kick and base cover screws, and the drain hose’s high loop to the disposal.
Click-in, leave-in, sharp-debris, no-scratch and knockout-plug zones
- Click it in Drain pump cover: press until it clicks (E:25 if loose)
- Leave in Suction cap: the repair manual says leave it in
- Sharp debris Impeller: glass and sharp debris, wear gloves
- No scratches Sump outlet: a scratch here can leak
- Knockout plug Disposal inlet: plug out before the hose goes on
Screws and latch (no screw length is published)
- Base cover screws (2) ×2
- Drain pump latch: lift, turn clockwise
- Toe kick screws · #2 Phillips (2) ×2
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed tub floor and base.
All 8 steps
- 1Unplug the dishwasher or switch off its breaker
Disconnect the dishwasher from its power supply before any part of the drain comes out: pull its plug out of the outlet, or switch off its breaker. Then take out both racks (our cutaway leaves them out).
- 2Turn the lower spray arm aside and sponge out the standing water
Turn the lower spray arm round so neither of its blades lies over the filter. Then soak up the standing water with a sponge and wring it into a bowl, until the tub floor is dry and only a film is left in the sump.
- 3Twist the filter counterclockwise, lift it out and take it apart
Turn the coarse filter’s handle counterclockwise and lift the whole filter system out: the cylinder (the coarse filter inside, the micro filter round it) with the flat fine filter around its neck. Take care that nothing falls into the open sump. On the bench, pull the micro filter down and off, press the coarse filter’s catches together and lift it out of the fine filter. Rinse all three under running water with a soft brush and a little soap, and clear the dirt from the rim between the coarse and fine filters.
- 4Pry the drain pump cover out with a spoon and clear the impeller trap
At the bottom of the sump, where the filter stood, sits the drain pump cover: grey, with a white handle across it. Slide a spoon under its edge and lever until it clicks free, grip the white crosspiece and lift the cover up and then forward out of the sump. The drain pump’s impeller is now in reach: with gloves on, take out food remnants and anything else caught round it, since Bosch warns that sharp debris such as broken glass can block the drain pump. Leave the second cap beside it alone: that is the suction cap over the heat pump, which the repair manual says should not be removed. Avoid this trap: BSH’s repair manual is plain: with no drain pump cover in the sump, water pressure cannot build up and the pump cannot pump. Its bulletins add that a loose cover lets more water reach the pump, its load and current rise and E:25 appears (now and then E:23 or E:24, or the Clean light as if the program had ended), and that drain pumps and controls have been replaced for it, parts nobody needed. Press the cover down until it clicks.
- 5Take the drain hose off the disposal and check the knockout plug and high loop trap
Still not draining? Look at the house side. Under the sink the hose must rise in a high loop at least 81 cm (33 in) above the floor, or run to an air gap, held by a non-metallic tie and free of kinks. Loosen the hose clamp at the garbage disposal, pull the hose off over a bucket and look into the disposal’s dishwasher inlet: on a new install, its knockout plug has to be knocked out before the hose goes on. Avoid this trap: The repair manual’s own warning: make sure the garbage disposal plug is removed before installation, because plugs have been left in and stopped the draining. On this platform its E:24 row says to remove the disposal plug, and Bosch’s US help page says the same for a hose run to a disposer; the newer models show E:61-03 for a disposal that is still plugged or a kinked hose.
- 6Bottom front access: take off the toe kick and the base cover
The check valve and the drain pump are reached from the front of the base. In the repair manual’s order the outer door comes off first (on most models, six short T20 Torx screws at the bottom of the inner door). Then the toe kick: pry off its decorative screw caps and keep them, take out its two #2 Phillips screws and tilt its bottom out and up. Pull the dishwasher out far enough to clear the hinges, remove the base insulation if your model has it, take out the base cover’s two screws, tilt its top forward and lift it until its slots clear the base. Full bottom front access also takes off the overflow trough, the inner door and the lower door seal; our cutaway leaves the door out.
- 7Empty the sump, pull the drain hose out and work the check valve out of the sump outlet
The check valve (BSH calls it the backflow valve) sits inside the sump at its outlet to the drain hose and stops waste water coming back into the sump. Empty the sump completely first. Pull the drain hose with its O-ring out of the outlet, then work the valve out with a small flat-blade screwdriver, carefully: a scratch inside the sump outlet can leak. A new valve slides in until it clicks.
- 8Unplug the drain pump, check its windings, lift the latch, turn it clockwise and pull it out
Disconnect the wire harness from the drain pump. Before buying a new one, measure its windings: about 80.5 Ω between any two of its three terminals at 20 °C (68 °F). BSH replaces a drain pump only when its impeller is damaged, a winding is open, or the pump is noisy or not working. To take it out, lift the latch, turn the pump clockwise and pull it out of the sump.
What you need
- A spoon, a sponge and a bowl, work gloves · for the owner’s clean-out: the standing water, the filters and the drain pump cover
- Needle-nose pliers and a small flat-blade screwdriver · for debris at the impeller, the hose clamp and the check valve
- A bit driver with #2 Phillips and T20 Torx bits, and a multimeter · for the technician’s bottom front access and the drain pump test
Questions
What do E24 and E25 mean on a Bosch dishwasher?
Bosch’s US help pages give E24 as not draining properly because the drain filter is blocked, and E25 as a blocked drain pump or a drain pump cover that is loose or missing. BSH maps E:24 to E 6102 and E:25 to E 6103 on newer displays.
I cleaned the filter and it still won’t drain. What now?
Check the drain pump cover first: it must be pressed down until it clicks. BSH’s bulletin puts a missing or unseated cover first among the causes of drain faults, because without it the pump cannot build up pressure. Then check the house side: the high loop, a kinked hose and, on a new install, the disposal’s knockout plug.
Where is the check valve, and how do I know it has failed?
Inside the sump, at its outlet to the drain hose, reached from the front of the base. The repair manual’s test: if water flows back into the sump after the pump has drained it, the valve may be stuck open. Clean the valve and the sump, and replace the valve if it still lets water back.
Do I need a new drain pump?
Usually not. BSH writes that many drain pumps are replaced unnecessarily and that debris in the drain system is the most likely cause. It replaces one only if the impeller is damaged, a winding is open (not about 80.5 Ω between two terminals) or the pump is noisy or not working.
My new Bosch dishwasher has never drained. What should I check?
The disposal’s knockout plug first: the repair manual warns that plugs have been left in on installs and stopped the draining. Then a kinked hose, and the high loop: at least 81 cm (33 in) above the floor, or an air gap, held by a non-metallic tie.
How often should the filters be cleaned?
Bosch’s Use and Care manuals ask you to check them for residue after every wash and to rinse them under running water when they need it.
Safety
Switch the dishwasher off at its breaker or pull its plug before any part of the drain comes out. Water stands in the sump, and the filters and the pump can hold broken glass and other sharp debris: wear gloves to lift it out.
- Mains power: switch it off and unplug it before you open it: its power supply runs on mains voltage. Never plug it in with a cover off.
About this teardown
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
Our 3D is a cutaway of the bottom of a Bosch 24-inch built-in dishwasher of the 2015–2022 platform that BSH’s repair manual calls GV640 (ManualsLib files it as the SHP65TL5UC): the stainless tub floor with its three filters, the sump with its drain pump cover and suction cap, the drain pump and check valve under it, and the base’s toe kick and base cover. Bosch’s current models, such as the 300 Series SHE53C85N, use the same filter and pump cover, removed the same way, but show newer codes such as E:61-02 and E:61-03. The whole machine is 86.0 × 59.8 × 60.3 cm (the SHE53C85N, Bosch’s spec page); our section is cut away at both sides and the back, and the size and place of every part inside is our estimate from the repair manual’s photos and words. The impeller’s 37 mm is Parts Town’s figure for drain pump 00620774. The hose’s run to its loop and to the disposal, a generic one of our own, is shortened, so the loop is not drawn at its real 81 cm (33 in). No Bosch logo or artwork is shown.
Where the owner’s brief differed, the real machine decides. The drain pump cover is grey with a white handle (Bosch’s own description of part 00611322), not white. Part 00611618 is a “Stop” on Bosch’s store, not the check valve: the check valve is 00611320, inside the sump’s outlet, worked out from below. The drain pump comes out by lifting its latch, turning it clockwise and pulling; no source gives the angle of that turn or the side it is seen from, so the turn we draw, seen from the front, is our picture and the text gives no angle. No source says a missing cover damages the pump: the repair manual says it cannot pump, and the bulletins tie a loose cover to E:25.
Our own estimates: every size and place inside the machine, the glass fragment caught at the impeller, the times on the scorecard and the hours on the Fix vs. Replace card, and how the drain hose sits in the sump outlet (the repair manual’s drawing shows the outlet open while the valve comes out, so we pull the hose out first, as its section on the sump drain hose does). The real drain hose runs up the machine’s left side to the water level control before it leaves the back; ours goes straight back. No screw length or torque is published for these parts, so the risk map gives none.
Prices are Bosch’s US list prices, read in November 2026 when every one of these parts was out of stock: drain pump cover $18.50, check valve $17.99, drain pumps $38.50 to $66.50 by model, filters $35.99 and $50.99. Fixr’s cost guide gives $150–$400 for a technician’s drain pump replacement and $50–$400 for will-not-drain repairs; a new Bosch 300 Series SHE53C85N lists at $1,099.
Sources: BSH repair instructions GV640ADW (document 58300000170749, filed by ManualsLib as the SHP65TL5UC; marked for BSH-authorised use, facts only): drain hose, high loop and disposal plug (2.4), drain pump and its 80.5 Ω windings (4.5), sump, drain pump cover, suction cap and backflow valve (4.14), filters (4.15), bottom front access (5.1.4), drain pump removal (5.6), sump parts (5.9), backflow valve (5.14), BSH sparepart information “Clean Out Drain System”, 58300000150815 B (July 2025): causes of drain faults, drain pump cover first, the flush test, when to replace a drain pump, BSH service bulletin 58300000150815 A (2 July 2010): E:25 from loose drain pump covers, parts 611322 and 611332, Bosch Use and Care manual, SHX78DC5N: filter system, cleaning the drain pump, E:61 codes, Bosch Use and Care manual, SPX68C75UC: filter system and cleaning the drain pump, Bosch US: dishwasher not draining, Bosch US: dishwasher error codes (E24 and the disposal plug, E25 and the spoon), Price: Bosch US, 300 Series Dishwasher SHE53C85N, $1,099.00, 33 7/8 × 23 9/16 × 23 3/4 in (read November 2026), Price: Bosch US store, drain pump cover 00611322, “gray with white handle”, $18.50 list, out of stock (read November 2026), Bosch UK store: drain pump cover 00611322 replaces 00628305, Price: Bosch US store, check valve 00611320, $17.99 list, out of stock (read November 2026), Bosch US store: part 00611618 is named “Stop”, Price: Bosch US store, drain pump 00620774 “Drain Pump BLDC”, $66.50 list, out of stock (read November 2026), Price: Bosch US store, drain pump 00631200, $38.50 list, out of stock (read November 2026), Price: Bosch US store, drain pump 00611332, $55.50 list, out of stock (read November 2026), Price: Bosch US store, coarse and micro filter 00645038, $35.99 list (read November 2026), Price: Bosch US store, coarse and micro filter 00615079, $50.99 list (read November 2026), Price: Bosch US store, drain mesh filters 00645037 ($27.50) and 00751458 ($24.50) (read November 2026), Parts Town catalog: drain pump 00620774 (37 mm impeller; SHE53T56UC/02, SHE68T55UC/03, SHE9PT55UC/B4), Parts Town catalog: drain pump 00631200 (SHE33T56UC/09, SHE7PT55UC/09, SGE53U52UC/98), Parts Town catalog: drain pump 00611332 (SHE3ARF2UC/08, SHX3AR75UC/07, SHX3AR75UC/14), Parts Town catalog: check valve 00611320 (SHE53T5, SHE65T5, SHX3AR5 families; white plastic), Parts Town catalog: filters 00645038 and 00615079 and the models they list, Price: Fixr dishwasher repair cost guide, drain pump replacement $150–$400, will-not-drain repairs $50–$400 (updated 31 January 2025; read November 2026).
The 3D models, drawings and text are our own. Bosch is a trademark of its owner, named only to say which device this teardown is for; iTakeApart is not affiliated with it.