How a car differential worksCar differentialCar differential

Steps ↓
Concept model Risk: High
How it works · in 3D Car differential

Illustrative 3D Concept Model — Generic Layout

🔴 Overall risk: High ⏱ An oil check takes minutes; setting up gears is shop work 💰 DIY vs. Shop
Step0/8
L wheel0rpm
R wheel0rpm
Carrier0rpm
Spiders0rpm
DriveStopped
What is inside8 steps · press play

3D Spatial Reconstruction: a generic model of our own design, built from published facts to show how the parts work together. Real ones differ by maker and model: always check your own before you open or adjust it.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this guide.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itCan it be opened at home?
Overall repair riskHigh
Time requiredAn oil check takes minutes; setting up gears is shop work
What can go wrongRunning it low on oil, or in a rebuild setting the backlash wrongly: noise and heat, and in time a failed gear or bearing.
Cost comparison DIY: the oil check and change, with the oil your manual namesGet the part ↗Get the kit ↗ Gear setup: a drivetrain shop; varies by shopSearch nearby repair shops ↗Opens local search results in Google Maps
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

FaultLow or old differential oil

Your time is worth
Fix it yourselfNo sourced figure
  • PartNo sourced figure
  • Toolsnot priced
  • TimeNo sourced figure
  • 3D risk levelHigh
Repair shopNo sourced figure
New or refurbishedUpkeep: nothing to replace
Consider a Repair ShopThe 3D risk level is High: one slip can cost more than a shop’s fee.Search nearby repair shops ↗Opens local search results in Google Maps

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. We found no fair, sourced figure for this yet, so the card gives no verdict it cannot back. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

8 steps · 41:11 ring and pinion · 16 and 10 teeth · work it live · 2 traps to avoid

How a car differential works: interactive 3D guide

Illustrative 3D Concept Model — Generic Layout

A rear differential you can see through, in 3D: the pinion and the ring gear, the carrier, the spider gears and the side gears, every tooth meshing, every speed worked out. Press Straight / Corner and watch the wheels share out the carrier’s speed; put one wheel on ice and see why the car stays put.

What is inside

A generic open rear differential of our own design, its housing see-through, on a display stand, with its half shafts and two wheels at a 1500 mm track. The propeller shaft brings the engine’s turn to an 11-tooth pinion, and the pinion drives a 41-tooth ring gear bolted to the carrier. Inside the carrier a cross pin holds two 10-tooth spider gears, and those mesh with two 16-tooth side gears, one on each half shaft. Steel for the ring and pinion, amber for the spiders, cyan for the side gears, and a cyan mark on each wheel so its turning can be counted. Press Straight / Corner at any moment and work it yourself.

Before you open it: the risk map

Seen through the housing before any work on it: the oil behind the cover, the pinion’s seal, the shims that set the ring gear’s place, and the filler plug that doubles as the level gauge.

Where to take care

What to find first

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed housing.

All 8 steps

  1. 1Why the wheels need different speeds

    Round a corner the outer wheel has further to go than the inner one. Take a corner of 6 m radius at the axle’s middle, with a 1.5 m track: the inner wheel runs on a 5.25 m circle and the outer on a 6.75 m one, so through this quarter turn the inner wheel travels 8.25 m and the outer 10.60 m. At 15 km/h, an illustrative moment, that is 109 rpm on the inside and 140 rpm on the outside. Join the two wheels with one solid axle and they would have to turn alike: one tyre would have to scrub away the difference, here 2.36 m in one corner.

  2. 2The engine’s turn comes in through the pinion

    The propeller shaft runs along the car. At the axle it turns the pinion, which meshes with the ring gear and turns the drive through 90°, across the car. The pinion has 11 teeth and the ring gear 41, so the pinion goes round 3.73 times for each turn of the ring gear: the speed comes down by that much, and the torque goes up by nearly as much. At the illustrative 15 km/h on this axle the propeller shaft turns at 463 rpm and the ring gear at 124 rpm.

  3. 3The ring gear turns the carrier as one trap

    Ten bolts hold the ring gear to the carrier’s flange, so the two turn as one piece, on a bearing at each end. The half shafts do not touch the carrier: they pass through its bores to the side gears inside. So the carrier cannot turn a wheel by itself. All it does is carry the cross pin round the axle, and the pin carries the two spiders. Under them the oil stands at the lower lip of the filler hole: on our axle that covers the ring gear’s lowest teeth, and each tooth comes through it once a turn. Avoid this trap: Gear oil is what keeps these teeth from touching. Let the level fall, from a leaking pinion seal or from a refill forgotten after a repair, and the ring gear no longer reaches it. Dana’s failure guide says what follows: low or no lube makes friction, which causes overheating, the protective film breaks down, and finally the mating surfaces seize; its photographs of low-lube gears show scored pinion teeth. Ford’s service manual lists a low level as a cause of an overheating axle, with the cure in one line: check it, and fill to specification. So check at the filler plug, on level ground, using the oil your manual names, and look for wet patches round the seals. How fast the level falls, the glow and the sudden stop are our picture: on a real axle it takes far longer.

  4. 4Straight on: the spiders are a lever

    Going straight, both wheels cover the same ground, so both side gears want the same speed. The pin pushes each spider at its middle, like the pivot of a balance beam, and the spider pushes on a side gear at each end of it, equally on both. Nothing makes it spin on its pin, so it does not: the spiders carry the turn as a lever would, and the carrier, the gears and both half shafts turn together in one lump. Watch the white tooth on a spider: it never moves on its pin. Left, right and carrier all read 124 rpm, the spiders 0.

  5. 5In a corner: the spiders walk round the slower side gear

    Turning right, the right wheel has less ground to cover, so it and its side gear slow down. The pin is still carrying the spiders round at the carrier’s speed, so they have to walk round the slower side gear, and that spins them on the pin. As they spin, their far side drives the left-hand side gear faster, by exactly what the right has lost. Here the camera rides on the carrier, so the carrier stands still: the side gears turn opposite ways and the spiders spin between them. At the illustrative moment that is 109 rpm on the right, 140 rpm on the left and 25 rpm for the spiders on their pin. Steer left and all of it reverses.

  6. 6The rule: the carrier is the average

    Add the two wheels’ speeds, halve them, and you have the carrier’s speed: always, in any corner, in any direction. The chart over the axle draws it: a bar for each wheel, a bar for the carrier, and a beam across the top of the wheels’ bars. Whatever the beam does, its middle stays on top of the carrier’s bar. So the engine and the gearbox decide the carrier’s speed, and the road decides how the two wheels share it. In a gentle 12 m corner the wheels read 132 and 117 rpm, in the 6 m corner 140 and 109, and the carrier reads 124 through all of it.

  7. 7The catch: one wheel on ice trap

    The same rule is the open differential’s weakness. Put the right wheel on ice: it has no grip, and the left wheel, which has, stands still. The average still holds: 0 rpm on the left and 249 rpm on the right give the carrier’s 124 rpm, while the spiders walk round the stopped side gear at 199 rpm. The turn goes to the wheel with the least grip, and the wheel with the most gets very little, so the car does not move. Easing off, as here, is the right start: spin the wheels as little as possible and rock the car between reverse and a forward gear. A limited-slip or locking differential is built to stop this happening. Avoid this trap: With one wheel stopped, the other turns at twice the carrier’s speed. So on a car whose speedometer reads the propeller shaft, 55 km/h on the dial is 110 km/h at the tread (the rule in step 6; our arithmetic, no maker’s words). Chevrolet’s owner’s manual warns that a tyre left to spin at high speed can explode and injure people, and that the car can overheat, and it gives a limit: no more than 55 km/h (35 mph) on the speedometer. Inside the axle, Dana’s failure guide calls this spinout: wheel spinning that makes enough heat to break down the oil film, so metal touches metal; it shows galled spiders, scored thrust washers and a galled cross pin, and says long-term spinout can break the whole axle down. Ease off, spin as little as possible, rock it, and call for a tow if that fails. The glow and how quickly it comes are our picture.

  8. 8The differential taken apart

    Everything out, in the order it comes. The oil is drained and the cover comes off the back of the housing. The half shafts are drawn back out of the side gears, and the carrier comes out of the back with everything in it. The propeller shaft and the pinion’s flange come off, and the pinion goes out through the housing. On the bench, the ten bolts come out and the ring gear slides off the flange. The cross pin slides out, so the side gears can be rolled round inside the carrier until the spiders stand in its windows and lift out, and then the side gears follow. Explode spreads the rest further.

What is in it

Questions

What does a differential do?

It lets the two driven wheels turn at different speeds while the engine drives them both. Round a corner the outer wheel has further to go, so it has to turn faster than the inner one, and the differential allows it.

What are spider gears?

The small bevel gears on the cross pin inside the carrier. Going straight they do not spin on their pin at all: they act as a lever pushing both side gears equally. In a corner they walk round the slower side gear, spin on the pin and drive the other side gear faster.

What is the difference between the ring gear and the pinion?

The pinion is the small gear on the propeller shaft, and the ring gear the big one it drives, bolted to the carrier. Together they turn the drive through 90° and bring its speed down: 3.73 times here, with 41 teeth on the ring gear and 11 on the pinion.

Why does one wheel spin and the other stay still?

That is an open differential doing what it always does. The two wheels’ speeds must average to the carrier’s, and it lets the turn go to the wheel with the least grip. One stopped wheel means the other turns at twice the carrier’s speed, and the car stays where it is.

Is it bad to spin one wheel?

Spun fast, yes. Chevrolet’s manual warns that a tyre can explode and gives a limit of 55 km/h (35 mph) on the speedometer, and with one wheel stopped the spinning tyre may be doing twice what the dial shows. Dana’s failure guide calls the damage inside spinout: heat breaks down the oil film on the spider gears and their pin. Ease off and rock the car instead.

What does a limited-slip differential do differently?

It limits how much the two wheels can differ, so the wheel with grip still gets some of the turn. The clutch type does it with a stack of plates that tie the two sides together. It is built to stop what step 7 shows, and a locking differential goes further still.

How do you check the differential oil?

With the car level, take out the filler plug: the oil should stand at the bottom of the hole. Toyota’s manual for one car gives 0 to 5 mm below the lip, and warns that too much or too little will lead to problems. Some differentials have no level plug of this kind, so go by your manual, and use the oil it names.

What is backlash in a ring and pinion?

The small play between their teeth. Shims behind the carrier’s bearings set it, moving the ring gear nearer to the pinion or further away, and one Dana procedure asks for 0.13 to 0.20 mm. Set wrongly it can bring noise, overheating and in the end gear or bearing failure, which is why refitting these gears takes a dial gauge and a manual.

What does 3.73 mean on a rear axle?

The ring gear’s teeth divided by the pinion’s: 41 ÷ 11 here. The propeller shaft turns 3.73 times for each turn of the wheels.

Safety

Most of a differential is out of reach without a lift. To check or change the oil, have the car level and on axle stands if you need to get under it, with nobody under a car a jack alone is holding up. Never start the engine while a jack holds the car. Gear oil and the housing are hot after a drive: wait for them to cool. Leave the setting of a ring gear and pinion to a shop unless you have the tools and the manual.

About this guide

3D Spatial Reconstruction: a generic model of our own design, built from published facts to show how the parts work together. Real ones differ by maker and model: always check your own before you open or adjust it.

The differential is a generic open rear unit of our own design, not any maker’s: an 11-tooth pinion and a 41-tooth ring gear (3.73:1, a ratio sold for many real rear axles), two 16-tooth side gears and two 10-tooth spiders, all module 5, a 1500 mm track and 640 mm tyres. Those counts are our choice: the ring gear’s teeth over the pinion’s give an axle’s ratio, and a real axle has its own.

Everything moves from two numbers: how far the carrier has turned, and half the difference between the wheels. The left wheel turns by the sum and the right by the difference, so the average of the two is the carrier’s, by construction. A spider turns on its pin at half the difference times 16 over 10, and the pinion at 41 over 11 of the carrier. The teeth are worked out, not drawn by eye: an involute tooth on each gear’s back cone, tapering to a common apex at the axle’s centre, with 0.2 mm of backlash, the top of the 0.13 to 0.20 mm in one Dana procedure. The clearance test checks that no tooth enters another at any moment of the guide.

The speeds in the readings are one illustrative moment: 15 km/h on a 640 mm tyre, which is 124 rpm, and a corner of 6 m radius at the axle’s middle, which gives 109 rpm on the inside and 140 on the outside. In step 6 the gentle corner is 12 m. On ice the figures assume the left wheel has grip enough not to turn at all. The 3D runs far slower than the readings say, so that the teeth can be followed.

What a real axle does differently. Most rear-drive cars use hypoid gears: curved teeth, with the pinion set below the ring gear’s centre for longer tooth contact and a lower propeller shaft. Ours has straight teeth and no offset, so that the gears’ pitch cones meet at the centre and each tooth can be seen. On many real axles the half shafts are held by C-clips inside the carrier, so the cross pin comes out before the shafts; ours simply draw back. The layout inside the housing and its proportions are our estimate.

The two traps are real failures. Low oil: Dana’s failure guide (for heavy truck axles) describes friction, overheating, the film breaking down and the surfaces finally seizing; Ford’s service manual lists a low level as a cause of an overheating axle; and Toyota’s and Ford’s manuals check the level at the filler hole’s lip. Spinning one wheel: Chevrolet’s owner’s manual gives the bursting tyre and the limit of 55 km/h (35 mph) on the speedometer, Dana calls the damage inside spinout, and Randy’s Worldwide reports the same in stuck cars’ spider gears. Our arithmetic gives the 110 km/h at the tread. How fast each one goes, the glow and the stop are our picture, not measurements.

Chevrolet’s 1937 film Around the Corner explained the idea with much the same pictures, and is still worth watching.

Sources: Wikipedia: differential (the outer wheels travel farther; one speed the average of the others; most power to the wheel with less grip; ring gear and pinion), Chevrolet: Around the Corner, 1937 film (the inside wheel turns slower than the outside one), as described by The Drive, Randy’s Worldwide: how spider gears work (motionless in the carrier going straight; heard in turns; free spinning overheats them), Randy’s Worldwide: gear backlash (the play between the gears; carrier shims set it; noise, overheating and gear or bearing failure), Dana Spicer: drive axle failure analysis, AXSM0020 (low lube; spinout; for heavy truck axles), Chevrolet Corvette 2009 owner’s manual: if your vehicle is stuck (a tyre spun fast can explode; 55 km/h on the speedometer; rocking it), Toyota RAV4 repair manual: differential oil (0 to 5 mm from the filler hole’s lower lip; too much or too little causes problems; hypoid gear oil), Ford Ranger 2019 workshop manual: differential fluid level check (to the bottom of the fill plug opening), Ford Ranger 2019 workshop manual: rear axle diagnosis (axle overheating: lubricant low; check it and fill to specification), JLG 26MRT manual: Dana/Spicer carrier section (backlash 0.13 to 0.20 mm), Wikipedia: spiral bevel gear (hypoid gears in rear-drive cars: the pinion set low, longer tooth contact), Wikipedia: bevel gear (pitch cones, whose apexes meet where the shafts’ axes cross), Wikipedia: limited-slip differential (what it does where an open differential does not), JEGS: 3.73 ring and pinion sets for GM and Ford rear axles (the ratio on real axles), The Ranger Station: removing rear axles (the bolt and the cross pin out before the C-clips and the shafts), Tahoe Yukon Forum: a rear axle rebuild (the bearing caps do not swap sides; keep track of the shims; the carrier out once the axles are out), Toyota Matrix 2003 owner’s manual: never start or run the engine while a jack holds the car, Merkur XR4Ti service manual: differential disassembly (the fluid drained and the cover off first), GM Square Body forum: a 3.73 set has 41 teeth on the ring and 11 on the pinion, stamped on the gear.

The 3D models, drawings and text are our own. The device shown is a generic one of our own design, not any one maker’s model.