Gaming Mouse Scroll Encoder & Switch FixGaming mouse encoder & switchGaming mouse

Steps ↓
✓ Spec-Researched Risk: Med 30–45 min
Teardown · step by step Gaming mouseencoder & switch

✓ Spec-Researched 3D Guide

🟡 Overall risk: Medium ⏱ 30–45 min 💰 DIY vs. Shop
Step0/5
Screws out0/4
ZIF ribbonLocked
EncoderWorn
Step riskLOW
What you need5 steps · press play

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this teardown.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itDIY or a repair shop?
Overall repair riskMedium
Time required30–45 min
What can go wrongCreasing the bottom PTFE glide skates with a metal tool, or yanking the top shell off and tearing the side-button ZIF ribbon cable.
Cost comparison DIY: parts and toolsGet the part ↗Get the kit ↗ Shop: varies by shopSearch nearby repair shops ↗Opens local search results in Google Maps A new PRO X Superlight is $149.99 from Logitech G (US price, checked November 2026); part prices vary by mouse and shop.
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

FaultScroll wheel or click faults

Your time is worth
Fix it yourselfNo sourced figure
  • PartNo sourced figure
  • Toolsnot priced
  • Time30–45 min
  • 3D risk levelMedium
Repair shopNo sourced figure
New or refurbished$149.99

New from Logitech: PRO X Superlight

Consider a Repair ShopThis repair needs soldering.Search nearby repair shops ↗Opens local search results in Google Maps

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

5 steps · 2 traps to avoid · PTFE skates, ZIF ribbon, rotary encoder height & L/R switches

Gaming Mouse Scroll Encoder & Switch Fix: interactive 3D teardown

✓ Spec-Researched 3D Guide

When a Logitech G Pro X Superlight, G Pro Wireless, or Razer Viper / DeathAdder starts scrolling backwards randomly or registering phantom double-clicks, the culprit is a worn mechanical rotary encoder or oxidized primary microswitch. See the complete teardown in 3D: how to warm and peel the bottom PTFE glide skates without creasing them, open the lightweight endoskeleton without ripping the side-button ZIF ribbon, and match the exact encoder millimeter height.

What you need

An ultra-lightweight wireless gaming mouse (modeled from the Logitech G Pro X Superlight & Razer Viper / DeathAdder architecture) on an anti-static mat: beneath the bottom PTFE glide skates hide the 4 perimeter #000 Phillips screws; inside the contoured upper shell sit the lightweight internal endoskeleton, the 3.7 V LiPo battery stuck to the carrier, the side-button ZIF ribbon cable, the main PCB with its optical sensor lens, the spoked scroll wheel, the mechanical rotary scroll wheel encoder, and the left and right primary microswitches.

Tools: Warm air / hairdryer & thin plastic pick, Phillips #000 screwdriver, Nylon spudger

Fits / Compatible Wireless Gaming Mice · Scroll Encoder Heights & Switch Specs

Wireless Gaming Mouse Rotary Scroll Encoder Height (mm), Switch Type & Screw Reference

Mechanical mouse scroll encoders are sized by their core height in millimeters (measured from the flat PCB top to the center of the hexagonal axle hole). Use the lookup table below before ordering a replacement TTC Gold, Kailh Red, or Alps encoder or left/right microswitches:

Mouse ModelScroll Wheel Encoder HeightPrimary L/R Click SwitchesBase Screws Under PTFE SkatesInternal Ribbon & Battery
Logitech G Pro X Superlight (GPX 1)8 mm mechanical rotary encoder (factory Kailh White/Silver → upgrade to TTC Gold 8 mm or Kailh Red 8 mm)3-pin mechanical (Omron D2FC-F-7N(G1) 20M → fits Kailh GM 8.0, TTC Gold 80M, Huano Blue Shell Pink Dot) on removable switch daughterboard4 × #000 Phillips (2 under front PTFE skate + 2 under rear horseshoe skate) + 6 internal endoskeleton screwsSingle folding orange ZIF FPC ribbon cable + 3.7 V 240 mAh LiPo (3-pin JST)
Logitech G Pro X Superlight 2 (GPX 2)8 mm mechanical rotary encoder on upper daughterboardLogitech Lightforce 5-pin hybrid optical-mechanical switches on hot-swap daughterboard4 × #000 Phillips perimeter screws under front & rear PTFE skatesMain ZIF FPC ribbon linking upper switch/encoder endoskeleton to HERO 2 base PCB + 290 mAh LiPo
Logitech G Pro Wireless (GPW) & G70310 mm mechanical rotary encoder (TTC Gold 10 mm / Alps 10 mm)3-pin mechanical microswitches (Omron 50M / 20M) on separate left/right click daughterboards4 × #000 Phillips under front & rear PTFE skates (G305 uses 10 mm encoder + 4 screws under 4 oval skates)Dual ribbon cables to top shell + 240 mAh LiPo battery
Razer Viper Ultimate / Viper V2 Pro / Viper V3 Pro9 mm (Viper Mini / Ultimate) or 11 mm (Viper V2 Pro / V3 Pro — TTC Gold / Kailh dustproof)Razer Gen-2 / Gen-3 Optical switches (clip-in optical module—no soldering required to swap L/R switches!)4 × #000 Phillips or Torx T6 under rear & front PTFE skates (or under bottom sticker)Side-button ZIF ribbon cable + 3.7 V 300 mAh LiPo (3-pin JST)
Razer DeathAdder V2 Pro / DeathAdder V3 Pro11 mm mechanical rotary encoder (Kailh / TTC Gold 11 mm)Razer Gen-2 / Gen-3 Optical hot-plug switches (or 3-pin mechanical on DeathAdder Essential with 9 mm encoder)4 × #000 Phillips / T6 screws beneath front & rear PTFE skatesUpper shell side-button ZIF flex cable + 300 mAh LiPo battery

How to Measure Any Mouse Encoder Height: Measure from the top surface of the PCB straight up to the center of the hexagonal axle hole in millimeters (8 mm, 9 mm, 10 mm, 11 mm, 12 mm, or 13 mm). The number is also stamped on the metal side wall of most Kailh and TTC encoders.

Before you open it: the risk map

Seen through the closed gaming mouse shell: the 4 × 4.5 mm #000 Phillips perimeter screws hidden beneath the front and rear PTFE glide skates, the short orange ZIF ribbon cable linking the side buttons and lightweight endoskeleton to the main PCB, the 3.7 V LiPo pouch battery, the optical sensor lens, the rotary scroll wheel encoder, and the left/right microswitches.

PTFE skate crease, ZIF ribbon tear, battery & sensor lens zones

Screw length map (4 × Phillips #000 under PTFE skates)

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed mouse shell.

All 5 steps

  1. 1Warm & peel the bottom PTFE glide skates, then unscrew the 4 base screws trap

    Warm the bottom PTFE glide skates to 40–50 °C for 20 seconds so the pressure-sensitive adhesive softens, then slide a thin flat plastic pick beneath the full thickness of the white PTFE and its black foam backing to peel the skates off flat. Use a #000 Phillips screwdriver to remove the 4 × 1.4 × 4.5 mm perimeter screws hidden in the skate wells. Avoid this trap: Virgin PTFE mouse skates are only 0.7 to 0.8 mm thick and deform permanently if bent sharply while the glue is cold. Digging a metal screwdriver or blade into the skate corner kinks the Teflon upward—leaving a raised crease that drags across cloth and glass mousepads.

  2. 2Crack the shell clips, hinge open the top shell & unlock the ZIF ribbon trap

    Ease the rear of the upper shell up 10 mm to disengage the front plastic hooks, then tilt the upper shell and lightweight internal endoskeleton open like a clamshell. Do not pull the shell away yet: use a nylon spudger to flip up the black locking actuator on the delicate orange ZIF ribbon cable connecting the side buttons to the main PCB, and unplug the 3-pin JST battery connector. Avoid this trap: Because the LiPo battery and side-button assembly are mounted to the upper endoskeleton while their connectors sit on the bottom PCB, yanking the top shell straight off pulls the short orange ZIF flex cable and battery wires taut—tearing the ribbon across its fold line.

  3. 3Separate the upper shell, lightweight endoskeleton & LiPo battery

    With the ZIF ribbon and battery plug free, set the upper shell and internal endoskeleton onto the mat beside the base. If replacing a degraded 3.7 V LiPo battery (240 mAh on G Pro X Superlight; 300 mAh on Razer Viper / DeathAdder), slide a flat nylon spudger dipped in a drop of isopropyl alcohol under the pouch cell to release its adhesive strip from the endoskeleton.

  4. 4Slide the spoked scroll wheel out of the rotary encoder hub

    Tilt the right axle of the spoked scroll wheel up off the middle-click tactile switch post and slide its 1.7 mm hexagonal left shaft straight out of the mechanical rotary scroll wheel encoder hub. Cover the clear optical sensor prism lens in the center of the PCB with a strip of Kapton tape so no dust or solder flux lands on the optics.

  5. 5Replace the rotary scroll wheel encoder & left/right microswitches

    Remove the worn mechanical rotary scroll wheel encoder (5 through-hole joints: 3 signal pins + 2 side mounting legs) and the double-clicking left and right primary microswitches (3 through-hole pins each: COM, NO, NC—or pull out the optical switch module on Razer optical boards), and fit the new dustproof TTC Gold / Kailh encoder and crisp microswitches flush against the PCB.

What you need

Questions

Why does my gaming mouse scroll wheel jump up and down in the opposite direction?

Inside the mechanical rotary scroll encoder, three tiny metal wiper fingers brush across a spoked contact wheel to send quadrature phase signals. Over time, silicone oil, dust, and metal oxide build up on the contact disc so the MCU misreads the phase order and jumps in the opposite direction. Replacing the encoder with a dustproof TTC Gold or Kailh Red encoder (or installing a pre-soldered switch/encoder daughterboard on the G Pro X Superlight) fixes it permanently.

How do I remove PTFE mouse skates without ruining them?

Warm the skates gently with a hairdryer (40–50 °C for 15–20 seconds) to soften the adhesive, then slide a thin, wide plastic pick underneath BOTH the white PTFE layer and the black foam adhesive layer. Lift slowly with a low angle so the Teflon never folds.

What size scroll wheel encoder does the Logitech G Pro X Superlight or Razer Viper use?

The Logitech G Pro X Superlight (1 & 2) uses an 8 mm encoder; the original Logitech G Pro Wireless and G305 use a 10 mm encoder; the Razer Viper Mini and Viper Ultimate use a 9 mm encoder; and the Razer Viper V2/V3 Pro and DeathAdder V2/V3 Pro use an 11 mm encoder.

Can I fix G Pro X Superlight double-clicking and scroll jumping without soldering?

Yes! On the Logitech G Pro X Superlight, the left/right microswitches and the 8 mm rotary scroll wheel encoder sit on a separate upper daughterboard connected by a single ZIF ribbon cable. You can swap that entire daughterboard in 15 minutes with just a #000 Phillips screwdriver and a spudger.

Safety

Turn the mouse power switch off and unplug the 3-pin LiPo battery connector before working on the PCB. Never puncture or bend the soft 3.7 V lithium-polymer pouch battery with metal tools.

About this teardown

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

This 3D teardown models the internal architecture of modern ultra-lightweight wireless gaming mice (specifically referencing the Logitech G Pro X Superlight and Razer Viper / DeathAdder series): a contoured 0.8 mm upper shell, an internal honeycomb endoskeleton carrying the 3.7 V LiPo pouch battery and side switches via a folding orange ZIF ribbon cable, a spoked scroll wheel driving a mechanical quadrature rotary encoder, a central optical sensor prism lens, and left/right primary microswitches.

If you prefer a 100% solderless repair on a Logitech G Pro X Superlight or G Pro Wireless, complete pre-soldered upper switch/encoder daughterboards (with a fresh 8 mm or 10 mm TTC Gold encoder and Kailh GM 8.0 switches already mounted) drop straight in via the single ZIF ribbon connector.

Sources: iFixit: Logitech G Pro X Superlight Teardown & Repair Guides (4 × #000 Phillips screws under front & rear PTFE skates, internal endoskeleton, folding orange ZIF ribbon cable, 240 mAh LiPo battery, 8 mm scroll encoder), iFixit: Razer DeathAdder & Viper Wireless Mouse Disassembly (PTFE skate removal, side-button ZIF ribbon, optical/mechanical switch replacement, rotary scroll wheel encoder), Price: Logitech G, PRO X Superlight wireless mouse, $149.99 new (9 November 2026).

The 3D models, drawings and text are our own. Logitech, G Pro X Superlight, Razer, Viper, DeathAdder, Kailh, TTC and Omron are trademarks of their owners, named only to say which device this teardown is for; iTakeApart is not affiliated with them.