Fix it yourself, pay a repair shop, or replace it?
- Part$0
- Toolsin the kit
- Time15–30 min
- 3D risk levelMedium
Plumber
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
7 steps · 2 traps to avoid · InSinkErator’s own unjam and reset · Lift & Latch mount
InSinkErator Badger 5 Garbage Disposal Unjam, Reset & Mount: interactive 3D teardown
A garbage disposal that hums but will not turn usually has something stuck in its grinding disk, and its overload protector has cut the motor. On an InSinkErator Badger 5 the whole fix comes in the box: the hex wrench turns the disk free from below, tongs lift the object out, and the red reset button on the bottom brings the motor back. See where each one is, and how its Lift & Latch mount locks and comes off, before you reach under the sink.
What you need
A disposer that hums but will not turn, or stops dead, usually has something stuck in its grinding disk, and its overload protector has switched the motor off. InSinkErator’s own fix needs no parts: switch off, turn the disk free from below with the hex wrench that came with it, lift the object out with tongs, let the motor cool and press the red reset button. If it then rattles or leaks at the top, its Lift & Latch mount is checked, and the disposer can be twisted off it.
Tools: Jam-Buster wrench (08305D), Long-handled tongs or pliers, Flashlight, Flat-blade screwdriver
- Lost the wrench? A standard 1/4-inch Allen wrench fits the same socket in the bottom.
Badger models of InSinkErator’s 2025 manual (Lift & Latch mount)
InSinkErator Badger models, heights and mounts
Height (A) is from the bottom of the sink to the bottom of the disposer. The 2025 manual also covers the Badger 100, 1XL, 500 and 700.
| Badger model | Motor | Height (A) | Warranty | MSRP (November 2026) |
|---|---|---|---|---|
| Badger 1 | 1/3 HP | 11-1/2 in | 2 years | $129 |
| Badger 5 (this guide) | 1/2 HP | 11-1/2 in | 5 years | $149 |
| Badger 5XL | 1/2 HP | 11-1/2 in | 5 years | not listed |
| Badger 5XP | 3/4 HP | 12-5/8 in | 6 years | $179 |
| Badger 5 (2007 sheet) | 1/2 HP | 12-5/8 in | not given | not given |
No matching series found. Clear the filter to view all compatible models.
Older Quick Lock mount: its lower mounting ring turns on its own, so it is the ring, not the disposer, that is turned until all three tabs latch over the ridges. Evolution models differ: EZ Connect, the Quiet Collar baffle (74653D, not for Badger disposers) and their own reset steps.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the disposer: the grinding chamber no hand may enter, the hex socket and the red reset button on its bottom, the cover over its wiring, and the Lift & Latch mount with its three screws and the lower ring’s wrench hooks.
No-hands, power and falling zones
- No hands Grinding chamber: tongs or pliers only
- Wrench out Hex socket: wrench out before power
- Mains wiring Wiring cover: breaker off first
- Falling Mount: hold it up, never under it
Mount screws, wrench hooks and the reset button
- Mounting screw (flat blade) ×3
- Red reset button
- Wrench hook ×3
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed disposer.
All 7 steps
- 1Switch the disposer off, then the water
Put the disposer’s wall switch to off before anything else, then turn off the water; let a full sink drain, or bail it out. The rule for every step that follows is InSinkErator’s own: never put a hand into the disposer.
- 2Turn the disk free from below with the wrench
Find the hex socket in the middle of the disposer’s bottom. Push one end of the Jam-Buster wrench into it and work it back and forth, both ways, until it turns a full circle freely. Some force is fine: InSinkErator made the wrench to bend before the disposer is damaged. Then take the wrench out. No wrench? A standard 1/4-inch Allen wrench fits.
- 3Lift the object out with tongs, never a hand
Shine a flashlight down the drain. If your Badger has the removable sink baffle (some do), lift it out; on one with a pleated gasket, reach through its flaps. Lift the object out with long tongs or pliers, and check the teeth round the edge of the grinding disk for anything else caught there. InSinkErator’s rule: never a hand in the disposer, at any time.
- 4Let the motor cool, then press the red reset button
The overload protector is the small red button on the disposer’s bottom, facing the floor. When it has tripped it stands out about 1/4 inch (5 mm) lower than when set. Let the motor cool 3 to 5 minutes, then press the button lightly until it stays in. If it will not stay in, wait ten minutes and try again.
- 5Cold water first, then the disposer: test it trap
Take the wrench out of the socket before the power goes back on. Turn the cold water on first, then the disposer, and let the water run a few seconds after you switch off. If it will not start, look for a tripped breaker or a blown fuse at the service panel; if it jams again, go back to the wrench. One that rattles or vibrates loudly may have come loose on its mount: step 6. Avoid this trap: Left in the socket after the jam is freed, the wrench is turned by the motor the moment the switch goes on, its long arm sweeping round under the disposer. InSinkErator’s manual: take the wrench out before reconnecting the power, and never hold it while the disposer runs.
- 6Check the mount: three screws even, lower ring locked trap
A disposer that rattles or leaks where it meets the sink is checked at its mount. Each of the three mounting screws must be tight and secure, all tightened evenly; InSinkErator gives no torque for them. Then put the wrench into the left side of one of the metal hooks on the lower mounting ring and turn it to the right: the three tabs ride up their ramps and over the ridges, and a click means it is locked. Avoid this trap: Pushed the wrong way, the wrench turns the disposer to the left: its tabs slide back down their ramps, the disposer drops away from the sink flange and its gasket lets go. Water finds the gap at the mount, and turned further the tabs come off the ramps and the disposer falls. Turn it right until all three tabs click over the ridges.
- 7Twist the disposer off its mount
Only when it has to come off: a new disposer, or a leak at the sink flange. Switch the power off at the circuit breaker or fuse box, and unplug a cord-connected unit. Disconnect the drain trap from the discharge tube, and the dishwasher hose if one is fitted. Hold the disposer up from below, put the wrench into the right side of a mounting lug on the lower ring and turn it to the left: the tabs slide down their ramps and the disposer falls free into your hands. Never have your head or body under it.
What you need
- The Jam-Buster wrench that came with the disposer · or a standard 1/4-inch Allen wrench
- Long-handled tongs or pliers and a flashlight · to see and lift the object out, never by hand
- A flat-blade screwdriver and a towel · for the mounting screws, and to set the disposer on
Questions
Where is the reset button on an InSinkErator garbage disposal?
Under the sink, on the bottom of the disposer, facing the floor: a small red button. When it has tripped it sits about 1/4 inch (5 mm) lower than when it is set. Let the motor cool 3 to 5 minutes, then press it lightly.
What size Allen wrench fits a garbage disposal?
InSinkErator says a standard 1/4-inch Allen wrench fits the hex socket in the bottom if the Jam-Buster wrench that came with the disposer (08305D) is lost. It goes into the middle of the bottom and is worked back and forth until the disk turns freely.
Why does my garbage disposal hum but not turn?
Usually something has stuck its grinding disk, such as a spoon or a toy, as iFixit lists, and the overload protector then switches the motor off. Switch off, free the disk from below with the wrench, lift the object out with tongs and press the reset button.
How long should I wait before pressing the reset button?
InSinkErator’s manual says to let the motor cool 3 to 5 minutes and then press the button lightly. If it will not stay in, its support page says to wait ten minutes and try again.
Can I pour drain cleaner into a garbage disposal?
InSinkErator’s manual lists caustic drain cleaners among the things not to put into a disposer. For a clog, its support page uses a plunger instead.
Is the splash baffle removable on a Badger 5?
On some units. The 2025 manual lists a removable sink baffle or a pleated mounting gasket on some models, and InSinkErator sells kit 78529-ISE to make a Badger’s baffle removable. The Quiet Collar baffle (74653D) is for Evolution models only. Knock out the dishwasher plug only if a dishwasher drains into the disposer: once out, it cannot be put back.
Safety
Power off before you work: the wall switch for a jam or a reset, the circuit breaker or fuse box before the disposer comes off or goes back on. Never put a hand into the disposer: tongs or pliers. Take the wrench out before the power goes back on. Never have your head or body under the disposer while it comes off or goes on: it can fall.
- Mains power: switch it off and unplug it before you open it: its power supply runs on mains voltage. Never plug it in with a cover off.
About this teardown
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
The 3D is today’s InSinkErator Badger 5 (1/2 HP, Lift & Latch mount), the model of InSinkErator’s 2025 Badger manual 81168, drawn to its submittal sheet: 11-1/2 in (292 mm) from the bottom of the sink to the bottom of the disposer, a 160 mm body, the outlet’s centre 152 mm under the sink and the tube’s leg 127 mm from the axis. It carries no logo, only a plain label of our own. Where the reset button, the wiring cover, the ramps, tabs, hooks and screws sit, how big they are, and how far the disposer turns between loose, locked and off, are our estimates from the manual’s drawings.
Where the brief differed, the real unit decides. The mount is held by three mounting screws tightened evenly and firmly, and InSinkErator gives no torque for them or for anything else in the job. The three tabs are on the disposer’s lower mounting ring and ride up three ramps on the sink-side mounting ring. No part numbered QLM-00 appears on any InSinkErator page we read: the wrench is 08305D. The wrench turns in the socket in the bottom, and the 1/4-inch is the Allen wrench the manual allows in its place. Only some current Badgers have a removable baffle, and the Quiet Collar baffle is for Evolution models only.
Our picture, not InSinkErator’s: the spoon (one of the things iFixit names), the cord-connected unit (the manual recommends its CRD-00 cord; a hard-wired one is switched off at the breaker the same way), the stand, the hands, and the loose mount at the start. The older Badger 5 of the 2007 sheet is 12-5/8 in tall, on the Quick Lock mount, whose lower ring turns on its own. InSinkErator’s limited warranty is void if you attempt to repair the product; the unjam and the reset are its manual’s own care steps.
Sources: InSinkErator: Fixing a jammed garbage disposal (switch off, the wrench in the bottom socket both ways until it turns freely, the 1/4-inch Allen wrench, no hand inside), InSinkErator: Resetting a garbage disposal (the red button on the bottom, about 1/4 inch lower when tripped, ten minutes), InSinkErator: Garbage disposal is making an unusual noise (lower mounting ring unlocked: wrench in the left side of the loop, rotate right, click), InSinkErator: Garbage disposal leaking from the mounting assembly (ring fully right, three screws tight and even), InSinkErator: Installing a replacement garbage disposal (ring turned left to release, the Quick Lock hang), InSinkErator: Fixing a garbage disposal that won’t grind (the shredding disk’s teeth, two swivelling impellers), InSinkErator: Fixing a clogged garbage disposal (a plunger, not drain cleaner), InSinkErator: Badger 5 product page (1/2 HP, 120 V, 6.3 A, 11-1/2 in, manual reset overload), InSinkErator Badger installation, care and use manual 81168 Rev A (2025): safety, releasing a jam, the reset, removal, the Lift & Latch mount, the leak test, InSinkErator Badger 5XL submittal sheet H1014-25E-83-10 (2025): the dimension drawing (11-1/2 in, 6-5/16 in, 6 in, 4 in, 5 in), InSinkErator Lift & Latch poster 79576-ISE Rev C (2021): all three tabs latched over the ridges, InSinkErator Badger 5 specification sheet H593-07E-64-02 (2007): the older 12-5/8 in Badger 5, InSinkErator store: Jam-Buster Wrench 08305D, InSinkErator store: Baffle Upgrade Kit 78529-ISE (for Badger disposals), InSinkErator store: Quiet Collar Sink Baffle 74653D (Evolution, not for Badger disposers), InSinkErator store: sink flange (4.5 by 1.75 in), iFixit: Garbage disposal hums (something stuck: a spoon, a toy; the hex key from below), iFixit: How to fix a leaking garbage disposal at the flange (the locking ring turned off, the unit caught), Price: InSinkErator, Badger series MSRPs (Badger 1 $129, Badger 5 $149, Badger 5XP $179; read November 2026), Price: Fixr cost guide, garbage disposal repair $100–$250 and a gasket or seal leak $60–$100 (read November 2026), Price: Fixr cost guide, garbage disposal installation $300–$600 and plumbers $75–$200 an hour (read November 2026).
The 3D models, drawings and text are our own. InSinkErator and Badger are trademarks of their owners, named only to say which device this teardown is for; iTakeApart is not affiliated with them.