Fix it yourself, pay a repair shop, or replace it?
- Part$95.45
- Tools$15
- Time1.5–3 h
- 3D risk levelMedium
Independent repair shop
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
7 steps · 2 traps to avoid · KitchenAid’s service order · Artisan KSM150 and other tilt-heads
KitchenAid Tilt-Head Stand Mixer Worm Gear Replacement: interactive 3D teardown
When a KitchenAid tilt-head mixer hums but its beater stays still, the fibre worm gear in the head is the usual suspect. Here it comes apart in 3D in KitchenAid’s own service order: the end cover and trim band, the pedestal off its hinge pin, the planetary, the gear case’s nine screws, the hub gear and the old grease, then the worm gear in its bracket. Explode spreads the layers; Reassemble puts it back with fresh grease.
What you need
A KitchenAid tilt-head stand mixer whose motor hums while the beater stands still. Its head splits into two halves: the gearcase-motor housing, with the motor and the steel worm on its shaft, and the bottom cover, which carries the gears in about 6 fl oz of grease. The fibre worm gear between them is what strips. KitchenAid’s service manual gives this order for the Artisan KSM150 and its tilt-head relatives, the K45SS, KSM75 and KSM90 among them.
Tools: Phillips #2 screwdriver, Flat-blade screwdrivers, one long, 5/32 in drift punch and a pin punch, Hammer with a nylon face, Putty knife
- Unplug the mixer before you take out a single screw: it is the manual’s first caution.
Part numbers and the tilt-head models they fit
KitchenAid tilt-head mixer gear case parts
Check the number on your own gear, or the parts list for your model and serial: the seller says its fit lists come from makers and suppliers.
| Part or model | Numbers | Fits, as listed | Price (Nov 2026) |
|---|---|---|---|
| Worm gear (fibre, metal hub) | WPW10112253 (W10112253, 4162897) | KSM150, KSM90, K45, K5 and others | $7.99 (Goodman’s) |
| Worm gear assembly (bracket and gear) | 4162101 (240309-2) | KSM150, KSM90, K45, K5 and others | $24.22 (Goodman’s) |
| Transmission case gasket | 4162324 / W11805888 | K45, K5, KSM90, KSM150 | $29.99 (Goodman’s) |
| Mixer grease | W11200218 (4176597, 4160588) | KitchenAid stand mixers | $57.47 (Goodman’s) · $67.99 (iFixit) |
| Tilt-heads with alike gearing (manual) | K45SS, KSM45, KSM75, KSM90, KSM103, KSM110, KSM150, KSM151, KSM152 | K45SS before 6 May 2002: 11-tooth pinion | — |
| Not this job: worm follower | W11086780 (9706529, 9703543) | bowl-lift KP2671, KP26M1X, KV25G0X | — |
No matching series found. Clear the filter to view all compatible models.
Worm gear or worm follower? The worm follower W11086780 (9706529) is sold for bowl-lift Professional mixers; a tilt-head’s fibre gear is the worm gear WPW10112253.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the closed head: the motor and its steel worm in the housing, the fibre worm gear on its bracket and the gear train in the bottom cover, the gasket joint between them, and every screw this job takes out, with the sizes KitchenAid’s manual gives.
No-pry, no-grease and check zones
- Unplug it first Plug: pull it before any screw
- No pry Gasket joint: never lever here
- No grease Motor side: keep grease out
- Check Hub gear: galled teeth strip gears
Screw map (sizes from KitchenAid’s manual)
- Trim band · #6-32 × 3/16 in ×2
- End cover · #6-32 × 3/8 in
- Bracket · #10-24 × 7/16 in ×3
- Case · #10-24 × 1 in fillister ×4
- Hinge pin set screw: loosen first
- Internal gear · #10-24 special ×5
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed mixer head.
All 7 steps
- 1Unplug it and take off the beater and the bowl
Pull the plug out of the outlet. Unlock the head and tilt it back, slide the flat beater off its shaft, then turn the bowl loose from the bowl screw cap on the base and lift it away. Lower the head again: the manual takes the bowl and any attachment off before anything else comes apart.
- 2Take off the end cover and the trim band
Undo the one tapered (oval) head screw at the top of the end cover, #6-32 × 3/8 in, and pull the cover back and up off the end of the head. Behind it, two #6-32 × 3/16 in screws hold the trim band to the gearcase-motor housing: take them out, hold the band at both sides and pull it off over the front of the head.
- 3Turn it over into a padded cradle and take the pedestal off
Lay the mixer upside down in a padded cradle, head down. Reach up inside the pedestal with a flat-blade screwdriver and loosen the hinge pin set screw until it clears the pin. Drive the hinge pin out with a drift punch and a hammer, then lift the pedestal off the gearcase bottom cover and stand it aside.
- 4Tap off the drip ring and drive out the planetary pin
The aluminium drip ring fits tightly round the planetary: set a screwdriver on its edge against the head and tap the screwdriver gently until the ring lets go. Drive out the groove pin that holds the planetary to the vertical centre shaft with a 5/32 in drift punch, then work the planetary off the shaft with two screwdrivers, one each side. Keep the washer on the shaft: it goes back on before the planetary.
- 5Free the cord and split the gear case trap
Slide the cord’s moulded strain relief out of its slot in the bottom cover. Take out the five #10-24 special screws that hold the internal gear in the bottom cover, then the four #10-24 × 1 in fillister head screws. Put a drift punch through the hole in the centre shaft and lift on it while a screwdriver in the slots in the side of the gear case breaks the bottom cover loose. The gears come away with the cover: keep its grease out of the motor side. Avoid this trap: The bottom cover sticks to the housing at its gasket. Lever a screwdriver into the joint itself, instead of the slots in the side of the gear case with a punch lifting the centre shaft, and the gasket is bent where the blade goes in. KitchenAid’s manual warns it may then not seal on reassembly; oil that separates from the grease can seep out of the head, even into the bowl. The bent lip and the seep are our picture.
- 6Pull the hub gear and scrape out the old grease trap
Pull the attachment hub bevel gear out of the hub: it clears the motor’s worm and comes out easily. Look at its teeth. Scrape as much of the old grease as you can out of both halves, keeping it away from the motor, then peel the old gasket off and clean the face it sat on. Avoid this trap: The worm gear is a fibre wheel, and a steel gear behind it with galled teeth keeps tearing at it. KitchenAid’s quick reference lists repeated worm gear failures under two causes: a galled attachment gear (replace the hub gear) and a galled attachment hub bearing (replace the gearcase-motor housing). Put a galled hub gear back and the new worm gear’s teeth are shaved off again; how fast that happens is our picture.
- 7Take the worm gear bracket out and change the worm gear
Take out the three #10-24 × 7/16 in Phillips filister head screws with their lock washers and lift the worm gear bracket off its two dowels. Drive out the groove pin through the worm gear and the pinion shaft, note where the two fibre washers sit, then drive the pinion shaft out from the top of the bracket. The stripped worm gear and the washers come free.
What you need
- Phillips #2 and flat-blade screwdrivers, one long · for the screws and the hinge pin set screw
- A 5/32 in drift punch, a pin punch and a hammer · for the groove pins and the hinge pin
- A new worm gear, mixer grease and a gasket · WPW10112253, W11200218 and 4162324
- A padded cradle and a putty knife · to turn the mixer over and scrape out the grease
Questions
Why does my KitchenAid hum but the beater does not turn?
KitchenAid’s help page says a gear can be stripped or damaged when something hard falls into the bowl, and to contact service if the motor runs but the beater does not. iFixit’s community pages put a hum with no beater movement down to the fibre worm gear, which they say is meant to give way so that an overloaded motor is spared.
The planetary turns but the beater does not: is it the worm gear?
No. KitchenAid’s manual gives that as a broken drive pin of the pinion inside the planetary, which is mended without splitting the gear case.
How much grease goes back in, and which one?
The manual fills the gear case with 6 fl oz of Benalene 930-2 grease or an equivalent, packed round the gears, and puts a little on the internal gear’s teeth. KitchenAid’s current mixer grease is W11200218, which replaces 4176597 and 4160588; we found no page that ties 4176444 to KitchenAid.
Worm gear or worm follower: which do I need?
On a tilt-head (KSM150, K45SS, KSM90) the fibre gear is the worm gear WPW10112253 (W10112253, earlier 4162897). The worm follower W11086780, which replaced 9706529, is listed for bowl-lift Professional mixers such as the KP2671, KP26M1X and KV25G0X.
Why does my mixer drip oil into the bowl?
Oil can separate from old gear grease and seep out of the head. The cure is fresh grease and, as the manual does every time, a new transmission gasket, never pried at when the halves are parted.
Is an old K45SS different inside?
K45SS mixers built before 6 May 2002 have an 11-tooth pinion (10 on all others) and turn about 280 rpm on 10 instead of 255, so check the serial’s date before you buy gears.
Safety
Unplug the mixer before you take out any screw, and wear eye protection while you drive pins with a punch. After a heavy load the head can be too warm to touch: let it cool first. Keep grease out of the motor side of the housing and off the rubber feet, which it softens. When it runs for the speed and bowl checks, keep sleeves and bracelets clear, stay with it and unplug it as soon as you finish.
- Mains power: switch it off and unplug it before you open it: its power supply runs on mains voltage. Never plug it in with a cover off.
About this teardown
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
The mixer is KitchenAid’s Artisan tilt-head, the KSM150PS, as we drew it: its proportions are our estimate, in a plain slate colour of our own and with no logo. Where the parts sit inside the head, their sizes and the gears’ tooth counts (all but the pinion’s 10) are our reading of the service manual’s photographs, not measurements.
The order, the screw sizes, the torques, the 5/32 in drift punch and the 6 fl oz of grease are from KitchenAid’s Stand Mixer Service Manual LIT4177310-C, which names the KSM150 among its tilt-head models (with the K45SS, KSM45, KSM75, KSM90, KSM103, KSM110, KSM151 and KSM152). The drives are iFixit’s: Phillips #2 for the end cover, the trim band and the bracket, a flat blade for the nine case screws. No source gives a length for the five special screws or a size for the worm gear’s pin punch, so neither is given.
Where common descriptions of this repair differ, the mixer decides: WPW10112253 is the worm gear, not the worm follower (a part for bowl-lift Professional mixers); there is no belt, since the motor’s worm drives the worm gear directly; the grease is KitchenAid’s W11200218, 6 fl oz of it; and the trim band has two screws, the end cover one.
The time and the hours in the Fix vs. Replace card are our estimates, and so is the shop’s total ($125 plus one part); the traps’ pictures (the bent gasket lip, the oil seep, how fast a galled hub gear shaves the new teeth) are ours.
Sources: KitchenAid Stand Mixer Service Manual LIT4177310-C (2005): tilt-head models including the KSM150; the disassembly order, the #6-32 and #10-24 screw sizes, the 5/32 in drift punch, the warning not to pry near the transmission gasket, 6 fl oz of grease, the torques and the problem-solving guide, iFixit, KitchenAid K45SSWH worm gear replacement (student guide): flat-blade gear case screws, three Phillips #2 bracket screws, a washer each side of the worm gear (comment), iFixit, KitchenAid KSM150PSER power cord replacement (student guide): the end cover’s Phillips #2 screw, the trim band’s Phillips #2 screws, the band pulled off the front, iFixit, KitchenAid KSM150PSER circuit board replacement (student guide): the end cover screw, unplug first, iFixit, KitchenAid KSM150PSER troubleshooting: a hum with no beater movement, the worm gear made to fail first, oil separating from the grease, iFixit, KitchenAid tilt-head mixers: the worm-drive gearbox and its plastic gear, iFixit, KitchenAid KSM150PSER device page: one model in many colours, KitchenAid product help: a beater that will not turn, a stripped or damaged gear, contact service, Parts Town, Whirlpool WPW10112253 “Worm Gear, Fiber, with Metal Hub” (name only; third-party price not used), Price: Goodman’s, KitchenAid mixer worm gear 4162897 / W10112253, $7.99, and its fit list (read November 2026), Price: Goodman’s, KitchenAid 4162101 worm gear assembly, $24.22 (read November 2026), Price: Goodman’s, KitchenAid mixer grease 4176597 / 4160588 / W11200218, $57.47, about 1 lb (read November 2026), Price: Goodman’s, KitchenAid mixer gasket W11805888 / 4162324, $29.99 (read November 2026), Goodman’s, KitchenAid worm follower 9706529 / 9703543 (W11086780): bowl-lift Professional fits, Price: iFixit, W11200218 Whirlpool mixer grease, $67.99 (read November 2026), Price: Mr. Mixer, tilt-head parts: pin punches $15 (read November 2026), Price: Mr. Mixer, services and pricing: regreasing and repair from $125 plus shipping, parts usually $15–$25 each, tilt-head rebuild $380 (read November 2026).
The 3D models, drawings and text are our own. KitchenAid and Artisan are trademarks of their owners, named only to say which device this teardown is for; iTakeApart is not affiliated with them.