Oral-B iO toothbrush battery replacementOral-B iO battery swapOral-B iO battery

Steps ↓
✓ Spec-Researched Risk: Med 5–10 min
Teardown · step by step Oral-B iO batteryswap

✓ Spec-Researched 3D Guide

🟡 Overall risk: Medium ⏱ 5–10 min 💰 DIY $19.99
Step0/6
ChargerPlugged
Neck sealSealed
Base capLocked
BatteryIn
Step riskLOW
What you need6 steps · press play

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this teardown.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itDIY or a repair shop?
Overall repair riskMedium
Time required5–10 min
What can go wrongFitting the new cell the wrong way round, tearing the neck gasket or leaving the ring unclipped so water gets in, or levering the cell with metal.
Cost comparison DIY: a cell $19.99, spudger and tweezers $8.98Get the part ↗Get the kit ↗ Shop: varies by shopSearch nearby repair shops ↗Opens local search results in Google Maps US prices from iFixit, checked November 2026; no repair shop price was found.
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

FaultBattery no longer holds a charge

Your time is worth
Fix it yourself$32
  • Part$19.99
  • Tools$8.98
  • Time5–10 min
  • 3D risk levelMedium
Repair shopNo sourced figure
New or refurbished$279.99

New from Oral-B: Oral-B iO Series 9

DIY Wins — Save ~$250Doing it yourself costs 89% less than a replacement, with your time at $25/hr.DIY against a replacement: 89% lessFind the partAmazoneBayiFixit

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

6 steps · 3 traps to avoid · No screws · The charger is the key

Oral-B iO toothbrush battery replacement: interactive 3D teardown

✓ Spec-Researched 3D Guide

An Oral-B iO Series 7, 8 or 9 handle taken apart in 3D to replace its battery: the brush head and the metal neck ring off, the base cap unlocked with the brush’s own charger as a key, the whole inside pushed out of the bottom, and the 49 × 14 mm lithium-ion cell levered out of its two sprung contacts, the new one going in the right way round. Press play to watch a step, Explode to spread the pieces along the handle, Reassemble to put it back together.

What you need

The Oral-B iO Series 7, 8 and 9 handle (Type 3758) has no screw to take out. Its base cap is a latch that the brush’s own charger unlocks like a key, and everything inside comes out of the bottom in one piece. The battery is a 49 × 14 mm lithium-ion cell held between two sprung contacts, not soldered. Two seals keep water out: a grey rubber gasket under a clipped metal ring at the neck, and a black seal on the base cap.

Tools: Plastic spudger, Precision tweezers

Which iO handles take this cell

Oral-B iO handles and their battery

Oral-B’s manuals give each iO handle a type number (Type 3758 for the iO Series 7, 8 and 9). The cell and the steps are the same from the iO3 to the iO10:

Series or partHandle typesBattery cellOral-B part number
iO3, iO4, iO5, iO6, iO7, iO8, iO9, iO103753, 3758, 3769, 3776, 3794, 3795, 379649 × 14 mm, 3.6 V0602589724096
iO2 (not interchangeable)37703.2 V0602589724119
Maker’s replacement, 14500CYiO3 to iO103.6 V, 750 mAh, 2.7 Wh0602589724096
iFixit, 740 mAhiO Series 6 to 103.7 V, 740 mAhIF389-008-1
iFixit, 750 mAhiO Series 6 to 103.6 V, 750 mAhIF389-009-1

Handle types and part numbers as ToothbrushBattery.com and iFixit list them (November 2026). The iO2’s 3.2 V cell does not fit the others, and theirs does not fit it.

Before you open it: the risk map

Seen through the closed handle standing on its charger: the grey gasket under the neck ring, the base cap the charger unlocks, the spring on its peg, the charging coil’s leads, the cell between its two sprung contacts and the + marks to note.

Seals, spring, coil and cell

Recesses, contacts and + marks

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed handle.

All 6 steps

  1. 1Run it down, unplug the charger, pull the head off

    Use the brush until the battery is nearly flat, below 25%, so the cell holds little energy when it comes out, and put on gloves and safety glasses in case it leaks. Pull the charger’s plug out of the wall: the charger is about to become a tool, and it must not be live. Pull the brush head straight up off the drive shaft, lift the handle off the charger and lay it on a soft support, display up.

  2. 2Lift the metal ring off the neck trap

    A stainless ring sits round the base of the grey drive shaft, clipped down over a soft grey rubber gasket. Slide one arm of the tweezers, or a small blunt flat blade, under the ring’s lower edge at the front and lift: the clips let go and the ring comes up and off over the shaft. Keep the tip on the ring’s edge and out of the grey rubber. Clean toothpaste and limescale off the ring and the gasket with little or no liquid, as liquid can run inside. Avoid this trap: The soft grey gasket under the metal ring is what keeps water out at the neck. Push a tweezer tip in too deep or too steep and it punctures the rubber; push the ring back on without its clips snapping into place and it sits crooked over the gasket. Either way, rinsing water runs down the shaft and into the handle. One owner reports a water-damaged brush with a dead display after the ring was not reseated properly, and water damage already done may not be cured by a new battery. Lift only by the ring’s lower edge, and press the ring down until it snaps into place all the way round.

  3. 3Unlock the base cap with the charger

    The base cap is not pried off. Turn the unplugged charger upside down: three shallow edges on its underside fit the three recesses in the cap. Stand the brush on it, base down, press it in, and turn the handle about 45° anticlockwise, an eighth of a turn (iFixit’s guide says about 90°). Then tilt the handle back slightly to free the seal and lift it straight off: the cap stays on the charger, with a small spring on its peg and a black seal round its spigot.

  4. 4Lift the cap off the charger and keep the spring

    Lift the cap off the charger. A small spring sits on a cross-shaped peg under the cap: take it off with tweezers and keep it in the tray, as it is easily lost. Look at the black seal in the groove round the spigot: it must be whole and clean to keep water out at the base.

  5. 5Push the inside out of the bottom

    Hold the handle and press the grey drive shaft at the top with your thumb: everything inside, the motor, the board, the cell and the charging coil, slides out of the open bottom in one piece, coil end first. Push it out from the shaft end rather than pulling it by the coil end, then turn it over: the cell lies on its back, in a white holder.

  6. 6Note the + end and lever the old cell out trap

    Before the cell moves, note which way round it sits: its + end has a small + and a groove round it, and the holder has a + moulded into it. A photo helps. Lever the + end up at the side gap with a plastic spudger, never a metal blade, and lift the cell out of its two sprung contacts. Tape both ends of the old cell and put it in a bag for battery recycling. Never refit a cell that is dented, swollen or damaged. Avoid this trap: A flat screwdriver or a knife seems the obvious lever, but at the + end a steel blade can touch the + contact and the cell’s metal case at once and short them: a short-circuited lithium-ion cell is dangerous, and Oral-B warns not to short the + and – terminals. iFixit says not to pry at the battery with metal tools, and one owner who did reports a brush that would no longer charge. A nylon spudger does the same job and cannot conduct.

What you need

Questions

Can you replace the battery in an Oral-B iO?

Yes, though Oral-B does not offer it as a repair: its European manuals call the battery non-replaceable, and every version warns that opening the handle destroys the appliance and voids the warranty. Its North American manual still shows how to open the handle and take the cell out at the end of the brush’s life, and iFixit rates the job easy, about 5 to 10 minutes, with no special tools.

What battery does the Oral-B iO use?

A cylindrical lithium-ion cell 49 mm long and 14 mm across, flat at both ends, often called the 14500 size. iFixit’s teardown found a 3.7 V, 740 mAh cell; the maker’s own replacement, 14500CY, is 3.6 V, 750 mAh and 2.7 Wh, part 0602589724096, for the iO3 to iO10. The iO2 takes a different 3.2 V cell that is not interchangeable.

How do you open the bottom of an Oral-B iO?

With its own charger, unplugged and turned upside down: the three shallow edges on its underside fit the three recesses in the base cap. Press the brush onto it, turn the handle about 45° anticlockwise (iFixit’s guide says about 90°) and lift the handle off; the cap stays on the charger. It is not pried off, and the small spring under it is easily lost.

Is the Oral-B iO battery soldered in?

No. It sits in a plastic holder between two sprung contacts and lifts out by hand once its + end is levered up with a plastic tool. The older Black 7000 was different: a 42 × 17 mm cell with soldered tabs.

Why won’t my Oral-B iO charge after a new battery?

The sources name a cell fitted the wrong way round, contacts flattened so they no longer press on the cell, a broken lead from the charging coil, or water damage that was already there. Check the cell’s + end against the holder’s +, bend flattened contacts gently out and test before closing. A forced reset is pressing the power and mode buttons together.

How long does an Oral-B iO charge last?

About two weeks of brushing twice a day, by iFixit’s and Electric Teeth’s accounts. A full charge typically takes 3 hours on the iO’s chargers (Types 3768 and 3786), and 12 hours on the Type 3757 charger, as Oral-B’s manuals give it.

Safety

Unplug the charger from the wall before you use it as the key, and never put it in water. Run the battery below 25% first, and wear gloves and safety glasses while the cell comes out, in case it leaks. Never pry at the cell with metal or let anything bridge its two ends; tape them and take the old cell to battery recycling, not the bin. Keep the handle below 50 °C (122 °F), and never refit a swollen, dented or damaged cell.

About this teardown

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

The brush is Oral-B’s iO Series 9 handle, Type 3758, which iFixit’s device page also gives for the iO Series 7 and 8: 18.3 cm long without its brush head, as Oral-B publishes it. Oral-B gives no width, so the 2.8 cm across is a review site’s measurement (Electric Teeth). The order of the steps, the opening, the seals and the cell follow Oral-B’s North American manual (21181481), iFixit’s iO battery guide and teardown, and ToothbrushBattery.com’s iO guide. No screw comes out: the motor’s Torx screws that iFixit’s teardown found are not touched. No logo, name or artwork of the maker is drawn in the 3D, and the charger is a generic round one of our own.

Where the brief for this guide differed from the brush, the brush decided. The bottom cap is not pried off: it is a latch that the charger, unplugged and turned upside down, unlocks like a key, its three underside edges in the cap’s three recesses; prying is how the older Black 7000 opens. Oral-B’s drawing and ToothbrushBattery turn the handle about 45° anticlockwise, iFixit’s text about 90°, and we say both. A spring sits under the cap and the cap’s spigot carries a black seal; a second seal, a grey gasket under a clipped metal ring at the neck, is the one the sources stress most. The inside slides out of the bottom when the drive shaft is pressed. The cell is a 49 × 14 mm lithium-ion cell between two sprung contacts, not soldered. That pulling the inside out by its coil end could tear the coil’s leads is our own warning: no source says it happens on the iO, though a seller of these cells names a broken coil lead as one cause of a brush that will not charge after a swap.

Our estimates, read off iFixit’s photos or our own design: where the parts sit inside and their colours, the tube’s wall and bore, the spring’s size and that its peg is on the cap, which end of the holder carries the + (check your own brush’s moulded +), the cell wraps’ colours, the charger’s size and shape, the foam cradle and the display’s icons. The traps’ pictures are ours too: where the gasket tears and how the water runs in, the spark where metal meets the cell, and the spark of a cell fitted backwards. The 3D runs faster than real hands do.

Oral-B’s own position: its European manuals call the battery non-replaceable and say to dispose of the whole brush; its North American manual says not to take the handle apart except to remove the battery for disposal, and shows how; every version warns that opening the handle destroys the appliance and voids the warranty. The iO2 uses a different 3.2 V cell that does not fit the other iO handles.

Sources: Oral-B North American manual 21181481 (Handle Type 3758 / 3796, iOsense charger Type 3786): battery removal at the end of the appliance’s life, p. 13, Oral-B European manual 91819245 (Handle Type 3758, charger Type 3768): non-replaceable battery, the 50 °C limit, magnets, Oral-B North American manual, 2019 (Handle Type 3758, charger Type 3768), Oral-B manual 91368234 (Handle Type 3753, charger Type 3757): charging times, iFixit: Oral-B iO Battery Replacement (the charger as the key, the neck ring and gasket, no metal on the cell), iFixit: How to open the Oral-B iO (and its comments on water damage), iFixit News: a teardown of the Oral-B iO (October 2020): the 3.7 V, 740 mAh cell, the charging coil soldered to the board, iFixit: Oral-B iO device page (handle Type 3758 for the iO 7 to 10), iFixit: Oral-B Black 7000 battery replacement (the older brush, pried open, its coil wire), ToothbrushBattery.com: Oral-B iO battery replacement, iO3 to iO10 (the spring, the black seal, polarity, the cap part way in), ToothbrushBattery.com: the maker’s 14500CY iO cell, 3.6 V 750 mAh 2.7 Wh, part 0602589724096, and the handle types it fits, Price: iFixit, 49 × 14 mm Li-ion Oral-B iO battery, 740 mAh, $19.99 (read November 2026), Price: iFixit, 49 × 14 mm Li-ion Oral-B iO battery, 750 mAh, $19.99 (read November 2026), Price: iFixit’s guide lists its spudger at $3.99 and tweezers at $4.99 (read November 2026), Price: Oral-B US, iO Series 9 Genius, $279.99 on sale, $329.99 list (read November 2026); also its 18.3 cm handle length, Oral-B US, iO Series 6: the handle’s 18.3 cm length and weight, Electric Teeth: Oral-B iO Series 10 review (the handle 2.8 cm across, about two weeks a charge), AP (May 2024): repairing an electric toothbrush, the iO opened with its charger and its mechanism slid out.

The 3D models, drawings and text are our own. Oral-B and iO are trademarks of their owners, named only to say which device this teardown is for; iTakeApart is not affiliated with them.