Fix it yourself, pay a repair shop, or replace it?
FaultBroken arm, camera or battery
- PartNo sourced figure
- Toolsnot priced
- TimeNo sourced figure
- 3D risk levelHigh
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
8 steps · 25 parts · a 154 mAh battery · flex through both hinges · 2 traps to avoid
Ray-Ban Meta X-ray anatomy: interactive 3D guide
A pair of Ray-Ban Meta glasses from 2023 opened the only way they can be without breaking them: in 3D. The frame turns see-through, each arm is shown in a cutaway (the main board in the left, the battery, touchpad and capture button in the right), the camera and the capture LED are seen in their corners, the left arm folds to show the flex bending through its hinge, the wiring moulded across the front is traced, the lenses and contacts are cleaned the way Meta says, and every part is spread apart. Press play to watch a step, Explode to spread the layers, Reassemble to put it back together.
On the bench
A pair of Ray-Ban Meta glasses from 2023, the first generation, in the Wayfarer frame with 50 mm lenses, a 22 mm bridge and 150 mm arms, stands open on an anti-static foam stand. Nothing here is unscrewed or cut: each arm is two plastic halves glued together and the front has its wiring moulded inside it, so this guide opens them in 3D only, layer by layer, and shows what every part does and the two places where people break them.
- Left and right are as you wear them: the camera is on your left, the capture LED on your right. Explode spreads the layers at any moment, and the Transparent view turns the frame to clear glass.
Before you open it: the risk map
Seen through the closed glasses: the flex inside both hinges, the glued arm halves, the battery, the flex moulded across the front and the capture LED that must not be tampered with.
Hidden flex, glue and battery
- Hidden flex Left hinge: the camera’s flex inside
- Hidden flex Right hinge: flex to the front
- Glued seam Arm halves glued: no pry
- No metal Battery: 154 mAh lithium-ion
- Moulded in Flex moulded across the front
- No tampering Capture LED: tamper turns camera off
What to know is there
- 12 MP camera window
- Capture button
- Charging contacts: clean them
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed glasses.
All 8 steps
- 1X-ray overview
The frame turns see-through. In the left arm, close to the hinge, lies the main board with Qualcomm’s Snapdragon AR1 Gen 1 and 32 GB of storage, and further back, just in front of the ear, a speaker. In the right arm are the lithium-ion battery, the touchpad along the outside, the capture button on top and the second speaker. In the front, the 12 MP ultra-wide camera sits in the top corner on your left and the white capture LED in the top corner on your right. Flex circuits join them all through both hinges and across the front, moulded inside it.
- 2Left arm: the AR1 main board
In this cutaway the outer half of the left arm lifts away; on real glasses the two halves are glued together and do not come apart without damage. Along the arm, close to the hinge, lies the main board: the AR1 Gen 1 processor and 32 GB of flash storage under metal shield cans, with the flex from the camera coming in through the hinge at its front end. The power switch sits on the inside of the arm by the hinge, joined to the board by a small flex of its own. Further back, just in front of the ear, the speaker has a chamber of its own. Then the half settles back.
- 3Right arm: battery, touchpad and button
The outer half of the right arm lifts away in the same cutaway. Here is the battery, a small lithium-ion cell reported at 154 mAh, good for up to about four hours of use (half of what Meta claims for the Gen 2’s); a flex runs along under it towards the hinge. On the arm near the hinge is the touchpad you tap and swipe, and on top the capture button. The speaker sits further back, towards the ear, as on the left. Nothing on this side reaches the main board directly: everything goes through the right hinge and along the wiring moulded across the front.
- 4Camera and capture LED trap
Press the capture button: for a photo the white capture LED on the front blinks briefly, and for a video it keeps blinking for as long as the camera records. The two sit at opposite corners of the front: the 12 MP ultra-wide camera in the top corner on your left, the LED in the top corner on your right. Meta made the LED of this generation 2 mm across, larger than the 0.9 mm one on the earlier Ray-Ban Stories, and gave it a blinking pattern. Both are wired to the same main board, the camera through the left hinge and the LED along the flex moulded across the front, and Meta says this model’s LED lights for every use of the camera because of the way the glasses are built. Avoid this trap: The capture LED tells the people around you that you are taking photos or video. With this generation Meta built in tamper detection that stops a capture if the LED is covered, and its privacy page says the glasses disable the camera when they detect the LED covered, physically tampered with or destroyed: no photos or videos until the light is detected as clear again. A blade at the LED’s window does not give you a hidden camera. It scratches the front, can break the LED, and leaves you with glasses whose camera will not work. Meta also removes listings for LED tampering services and takes legal action against people who sell them. Leave the LED alone; if it is damaged, contact Meta’s support.
- 5Through the hinge trap
The left arm folds in and opens again. Each hinge is a metal part screwed to the frame, and a flex circuit runs right through it: on this side it carries the camera’s connection from the front into the main board in the arm, so every fold bends it a little round the hinge. The arm is not clipped on. Two screws hold it, but the flex inside means it does not come off the way an ordinary sunglasses arm does. Avoid this trap: On ordinary sunglasses an arm comes off once its hinge screw is out, so people try the same here, to tighten a loose arm or swap a frame. But the flex circuit that carries the camera’s connection runs through the metal hinge into the arm. With the screws out, the arm pulls away only as far as the flex lets it, and then the flex tears where it bends in the hinge: the camera is cut off from the main board, and nothing inside the glued arm can be mended by hand. Owners have reported frames splitting at this joint, most often on the left, and severing the camera cable. Leave the hinge screws alone, fold the arms gently, and take a loose or broken hinge to Meta’s or Ray-Ban’s support.
- 6Across the front
The battery is in the right arm and the main board in the left, so power and signals cross the front: a flex circuit runs from the right hinge along the top of the frame, over the bridge and on to the left hinge, moulded into the plastic so that it cannot be lifted out. A pulse of light runs along it here to show the way it goes. Two charging contacts sit on the inside of the nose bridge, where the case meets them, and one of the glasses’ five microphones is moulded into the right side of the nose bridge.
- 7Clean what you can reach
This is the care Meta gives for these glasses, and it is all that needs doing at home. Wipe the lenses, the camera’s window and the charging contacts on the nose bridge with a soft, clean cloth dampened with a little mild soap and water: never solvents or alcohol, never a dirty or rough cloth, and never under a running tap. Dry them before they go back into the case or on your face. If the case’s light stays dark when you dock them, clean the contacts on the nose bridge and in the case and dock them again.
- 8Every part apart
Every part rises out of its place: over the front, the flex moulded across it, the camera and the capture LED, the charging contacts and the nose microphone; over each hinge its metal part, its two screws and its flex; over the left arm the main board, the power switch and the speaker; over the right arm the battery, the touchpad, the capture button and the speaker; and over each arm, highest, its glued outer half. Drag to turn it round; the Explode slider spreads it further. Press Reassemble to bring it all back together.
What is in the 3D
- Ray-Ban Meta (Gen 1, 2023) · the Wayfarer, 50 mm lenses, 150 mm arms
- A soft cloth · the only tool the owner needs
- Nothing to open them with · the arms are glued and the hinges carry the flex: this page opens them in 3D only
Questions
Where is the battery in Ray-Ban Meta glasses?
In the right arm, on the first generation from 2023: a small lithium-ion cell reported at 154 mAh in a teardown and by reviewers (Meta does not publish the figure), with the touchpad and the capture button beside it. The main board with the Snapdragon AR1 Gen 1 is in the left arm.
Can you replace the battery yourself?
Not in any practical way. Each arm is two plastic halves glued together, the battery is wired in, and we found no spare battery or repair price published for this model. iFixit, opening the sibling Oakley Meta HSTN, called splitting the glued arm shells a one-way trip, found no replacement parts on sale and noted that an opened arm loses its IPX4 splash rating.
Can the arms be taken off or swapped?
No. Two screws hold each arm at its hinge, but a flex circuit runs through the metal hinge into the arm: on the left it carries the camera’s connection to the main board. With the screws out, pulling the arm off tears that flex. Owners have also reported frames splitting at that joint and severing the camera cable; a loose or broken hinge is one for Meta’s or Ray-Ban’s support.
What happens if the capture LED is covered or damaged?
Meta says its glasses disable the camera when they detect the capture LED covered, physically tampered with or destroyed, and no photos or videos can be taken until the light is detected as clear again. The LED has no off switch; it is there so that the people around you know when you are recording. Meta also takes legal action against people who sell LED tampering services.
Are the camera and the LED wired together?
Not side by side: on the 2023 glasses the 12 MP camera is in the top corner on the left and the 2 mm LED in the top corner on the right, both wired to the same main board in the left arm. Meta says this generation’s LED lights for every use of the camera because of the way the glasses are built.
How should I clean Ray-Ban Meta glasses?
With a soft, clean cloth dampened with a little mild soap and water, over the lenses, the camera lens and the charging contacts on the nose bridge, then dry them before they go back in the case. Meta says never to use solvents or alcohol, a dirty or rough cloth, or running water. If they stop charging in the case, clean the contacts on the nose bridge and in the case.
Does this guide fit the Ray-Ban Meta Gen 2 or the Oakley Meta?
It shows the first generation (2023). Meta’s Gen 2 (2025) is rated for up to 8 hours of use instead of about 4, records 3K video, and its case holds 48 hours of charge instead of 32; we found no published teardown of its insides, so we do not draw them. The Oakley Meta HSTN shares the same chip, storage and speaker, according to iFixit’s teardown, but its battery sits in a metal shell and its frame differs. Meta has since added a Gen 3.
Safety
The right arm holds a lithium-ion cell: never cut, pierce, crush or heat an arm, and keep a pair whose arm swells, gets hot or smells away from anything that burns. The arms are glued and the hinges carry the flex, so there is nothing to unscrew or pry at home; this page shows the inside in 3D so that nobody has to open them.
- Lithium-ion batteries: never bend, puncture or pry a battery with metal. A damaged cell can go into thermal runaway: it smokes, catches fire and can explode. Discharge it below 25% first; if it swells, hisses, smokes or gets hot, stop and move it somewhere safe.
- Static (ESD): work on an anti-static mat with a grounded wrist strap; a spark you cannot feel can kill a chip.
About this guide
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
The glasses are our own model of the first-generation Ray-Ban Meta from 2023 (the Wayfarer, model RW4006, in the standard size with 50 mm lenses, a 22 mm bridge and 150 mm arms, the sizes on its retail listing), with no logo, name or artwork anywhere. We chose this generation over the Gen 2 of 2025 because it is the one with a published teardown of its insides. Where the parts sit follows that teardown, by Intretech’s Secrets of Scale channel (the main board and the power switch in the left arm, the 154 mAh battery in the right with a flex under it, the flex routed through machined metal hinge parts, a connection moulded across the front from the battery to the board, the charging contacts and a microphone in the nose piece, and two screws holding each arm), and Meta’s own pages (the camera in the top corner on the left, the LED on the right, the touchpad and capture button on the right arm, the power switch inside the left arm by the hinge). We read that teardown through a transcript summary of its video. The parts’ sizes and shapes, where the speakers sit along the arms, the flex’s exact route, where the two hinge screws sit and the shape of the contacts are our estimates.
Where the brief this page was made from differed from the glasses, the glasses decided. It had the camera and the privacy LED hardwired together; on these glasses they sit at opposite corners of the front, the camera wired through the left hinge and the LED along the flex moulded across the front, both to the one main board, and Meta says this generation’s LED lights for every camera use because of how the glasses are built. It called the touch strip capacitive; Meta calls it a touchpad, and we found no source for how it senses, so the page does not say. It described a temple hinge to unclip; the hinge is screwed, two screws an arm, and its trap is taking those screws out. And it named getting round the privacy LED as a trap; this page shows only what Meta says happens, that the camera is disabled, and nothing about how anyone might try.
Some facts come from a sibling product, and are marked as such: iFixit’s teardown of the Oakley Meta HSTN (2025), built on the same platform, found the same AR1 Gen 1 chip, 32 GB of storage and speaker as in the Ray-Bans, glued arm shells whose splitting it calls a one-way trip, Torx screws at the hinges hiding delicate flex cables to the camera, a battery that comes out only with the right tools and no spare parts on sale, and it noted that opening an arm ends its IPX4 splash rating. It also found the Oakley’s battery in a metal shell, unlike the Ray-Ban’s. The 154 mAh battery figure is the teardown’s and reviewers’; Meta does not publish it. We drew the hinge screws with Torx heads because the sibling has them; the Ray-Ban’s are not confirmed.
The hinge trap follows the hinge’s build and reports of real failures: owners described frames splitting at the arm’s joint, most often on the left, and severing the camera cable (TechIssuesToday, July 2025, from Reddit reports). How far the arm pulls and where the flex tears is our picture. The LED trap shows only Meta’s own statements: its bystander-privacy paper (the LED 2 mm in this generation, against 0.9 mm on Ray-Ban Stories, with tamper detection built in) and its privacy page and July 2026 post (the camera disabled when the LED is detected covered, tampered with or destroyed). The 3D runs faster than real hands, the pulse of light along the front’s flex is only a picture of the way it runs, and the time to clean them is our estimate.
Sources: Intretech, Secrets of Scale: Ray-Ban Meta Smart Glasses Teardown (video: the board and power switch in the left arm, the 154 mAh battery in the right, the metal hinge parts routing the flex, two screws an arm, the moulded connection across the front, the contacts and a microphone in the nose piece), Transcript summary of the Intretech teardown (what we read of it), iFixit: Oakley Meta HSTN teardown, a sibling on the same platform (the same AR1 Gen 1, 32 GB and speaker as the Ray-Bans, glued arms, Torx hinges hiding flex to the camera, no spare parts, IPX4 lost once opened), Meta Newsroom, 2023: the new Ray-Ban Meta glasses (Snapdragon AR1 Gen 1, 12 MP ultra-wide camera, five microphones, open-ear speakers, IPX4, prescription-ready, from $299), Meta: bystander privacy paper, 2026 (the LED 2 mm against 0.9 mm, tamper detection, the first generation’s LED lights for every camera use because of its architecture), Meta: privacy settings for AI glasses (the camera disabled if the LED is covered, physically tampered with or destroyed), Meta Newsroom, July 2026: AI glasses, your questions answered (the LED has no off switch; tampering services removed and pursued), Meta Help: AI glasses accessibility FAQ (the camera top left, the LED on the right, the touchpad and capture button on the right arm), Meta Help: turn AI glasses on or off (the power switch inside the left arm, by the hinge), Meta Help: care and cleaning tips (a damp cloth with mild soap, no solvents, alcohol or running water; the lenses, camera lens and nose-bridge contacts), Meta Help: charging AI glasses (docked by the nose bridge; clean the contacts if the case light stays dark), Meta Newsroom, 2025: Ray-Ban Meta (Gen 2), up to 8 hours, 3K video, 48 hours from the case, from $379, Meta: Ray-Ban Meta (Gen 3), the current generation’s page, Laptop Mag: Ray-Ban Meta review (a 154 mAh battery, up to 4 hours), Moor Insights & Strategy: Ray-Ban Meta review (a 154 mAh battery), TechIssuesToday, July 2025: Ray-Ban Meta frames splitting at the arm’s joint, most often on the left, severing the camera cable (from owners’ reports), Fashion Eyewear: Ray-Ban Meta Wayfarer RW4006 listing (lens 50 mm, lens height 41 mm, bridge 22 mm, arm 150 mm), Price: Target, Ray-Ban Meta (Gen 2) Wayfarer, $379.99 new; the 2023 first generation is listed at $224.99, out of stock (9 November 2026).
The 3D models, drawings and text are our own. Ray-Ban, Wayfarer, Meta, Ray-Ban Stories, Oakley and Snapdragon are trademarks of their owners, named only to say which device this guide is for; iTakeApart is not affiliated with them.