Fix it yourself, pay a repair shop, or replace it?
FaultWorn battery or damaged ring
- PartNo sourced figure
- Toolsnot priced
- TimeNo sourced figure
- 3D risk levelHigh
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
6 steps · 2.6 mm wall · an 18.5 mAh potted cell · no screws, no seams · 2 traps to avoid
Galaxy Ring anatomy – why it won’t open: interactive 3D guide
A Samsung Galaxy Ring, opened the only way it can be without destroying it: in 3D. It charges in its case through two coils, then it is seen through its titanium frame and its epoxy, turns to show the flexible board and the three sensor bumps, then the lithium-polymer cell potted along one side under its charging coil, and where a stuck or swollen ring may be cut. Last, every layer spreads apart. Press play to watch a step, Turn 360° or Peel the Layers to work it yourself, Explode to spread the layers, Reassemble to put it back together.
On the bench
A Samsung Galaxy Ring in size 9 lies flat on a round anti-static foam pad, its clear charging case beside it. It is modelled to the published sizes: 18.9 mm across inside, 24.1 mm outside, 7.0 mm wide and 2.6 mm thick, and 2.7 g. Nothing here is unscrewed or pried: the ring has no screws, no clips and no seam, only a titanium frame filled with cured epoxy, so this guide opens it in 3D only, layer by layer.
- Explode spreads the layers along the ring’s axis at any moment, and the Transparent view turns the titanium and the epoxy to clear glass.
- Turn 360° and Peel the Layers, under the picture, let you work the ring yourself.
Before you open it: the risk map
Seen through the closed ring: the lithium cell potted along one side under its coil, the press connector sealed in, the seamless epoxy inside, and the orientation mark over the three sensor bumps.
No blade, no pick, no cutter
- No blade Lithium cell, potted inside the titanium
- Hidden coil Charging coil laid over the cell
- Sealed in Press connector, sealed in epoxy
- No pry Epoxy inside: no seam to pry
What to find first
- Orientation mark: towards your palm
- Three sensor bumps ×3
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed ring.
All 6 steps
- 1How it charges: two coils, no port
Open the clear charging case and stand the ring in its holder with the orientation mark on its outside lined up with the marker on the holder, as Samsung’s guide says. The ring has no port: a coil in the case and a coil inside the ring, laid over its battery, pass the power across with nothing touching, which is how a sealed ring charges at all. Samsung gives about 80 minutes for a full charge in the case. Then lift the ring back out onto the pad and close the case.
- 2X-ray: titanium outside, epoxy inside
Seen through, the ring is two shells and what they hold. Outside is the titanium frame: the concave band you see and its two edges. Samsung puts titanium on the frame only; the surface that touches your skin is epoxy, moulded into the frame and filling it, so the board, the sensors, the cell and the coil are all set solid inside. There is no lid, no clip and no screw anywhere. The ring turns once on the pad so you can see all the way round it.
- 3The flexible board and the three sensor bumps
The ring turns its sensor side to the back, so you look at its inner face. Inside the epoxy a flexible circuit board runs round the ring; Samsung’s launch display showed nine versions of it, one for each size, so each strip fits its own ring. Its sensors look out through three small bumps on the inside, under the orientation mark, which is why the mark goes towards your palm: the optical bio-signal sensor, whose LEDs shine into your finger while its light sensors read what comes back, for heart rate and blood oxygen, and the skin temperature sensor. The accelerometer, which feels your movement, sits on the board too.
- 4The potted cell, its coil and the press connector trap
The ring turns its cell side to the back. Along one side, right inside the titanium, lies the battery: a lithium-polymer pouch, which iFixit found on its CT scan with the charging coil sitting on top of it. In size 9 Samsung rates it at 18.5 mAh (19.5 mAh typical); sizes 5 to 7 have less and sizes 12 and 13 more. The cell and the coil reach the board through a press connector rather than solder, yet that connector is sealed into the epoxy with everything else, so it helps nobody change the battery. To get in, iFixit had to melt the epoxy and chip it away with a dental pick, and the ring was destroyed doing it. Avoid this trap: The inside looks like a plastic liner that ought to lift out, so people dig at it with a pick or a craft knife to get at a worn-out battery. But it is cured epoxy moulded into the titanium, with no seam to start from, and the flexible board, the charging coil and the lithium-polymer pouch lie only a millimetre or two under its surface. The point chips the epoxy, cuts through the board and the coil and goes into the pouch, and a pierced lithium cell can short inside, heat up, smoke and catch fire, an inch from your hand. Samsung says not to take the ring apart yourself, and iFixit only reached the cell by melting the epoxy and destroying the ring. A worn or damaged ring is a matter for Samsung’s support, not a pick.
- 5If it swells or sticks: where it may be cut trap
In our picture the cell swells, as a failing lithium cell can, and pushes the epoxy in towards the finger, so a ring that fitted grows tight. If yours is stuck, Samsung’s advice is to wet the finger with cold water and soap and turn the ring off slowly, to cool a swollen finger in cold water, and to hold the hand above your heart. If it still will not come off, a medical professional cuts it, and only along the orientation mark, where the battery is not; if one cut is not enough, a second about 1 cm to one side of it. Never cut it yourself. Then our picture goes back to a healthy ring. Avoid this trap: A ring that has gone tight feels urgent, and a ring cutter or a pair of nippers looks like the answer. But the cell runs along one side of the ring, right inside the titanium, and a wheel or a blade that cuts there goes through the thin wall into the pouch. Samsung warns that the ring holds a battery that is a safety risk if damaged, and that it must be cut only along the orientation mark, where the battery is not, by a medical professional; when a swollen Galaxy Ring was taken off at a hospital in 2025, it came off with ice and lubricant, without cutting near the cell. Soap and cold water first, the hand raised, then a professional, at the mark.
- 6Every layer apart
In this cutaway every layer rises apart along the ring’s axis: the titanium frame stays on the pad, then the epoxy with its three bumps, the flexible board with its sensors, its chips and the press connector, the charging coil, and the lithium-polymer cell at the top. The real ring cannot come apart like this: the epoxy is one cured piece round everything. Press Reassemble to bring it back together, or Peel the Layers to lift the frame and the epoxy off in 3D.
What is in the 3D
- Samsung Galaxy Ring, size 9 · its frame, epoxy, board, sensors, cell and coil
- Its charging case · with its own coil
- Nothing to open it with · it is sealed in epoxy: this page opens it in 3D only
Questions
Can you replace the battery in a Samsung Galaxy Ring?
No. The lithium-polymer cell, the charging coil and the board are set solid in epoxy inside the titanium frame, with no seam, screw or clip. iFixit only reached the cell by melting the epoxy and chipping it away, which destroyed the ring, and Samsung says not to take it apart yourself.
What is the inside of a Galaxy Ring made of?
Epoxy. Samsung puts titanium on the frame only, the outside and the edges; the inner surface that touches your skin is epoxy moulded into the frame, with three small bumps where the sensors look out.
Where is the battery in a Galaxy Ring?
Along one side of the ring, right inside the titanium: iFixit’s CT scan showed a lithium-polymer pouch there with the charging coil on top of it. It is not under the orientation mark, which is why the mark is the one place a medical professional may cut a stuck ring.
How does a smart ring charge without a port?
Through two coils. A coil in the charging case passes power across to a coil inside the ring, laid over its cell, with nothing touching. Samsung gives about 80 minutes for a full charge in the case.
What should I do if my Galaxy Ring is stuck or its battery swells?
Samsung’s advice: wet your finger with cold water and soap and turn the ring off slowly, cool a swollen finger in cold water and hold your hand above your heart. If it still will not come off, have a medical professional cut it, only along the orientation mark, where the battery is not. Never cut it yourself, and stop wearing a ring that grows tight or whose battery life suddenly drops.
How is the Oura Ring different inside?
Oura’s Gen3 has a titanium outside and a non-metallic inner moulding, with green, red and infrared LEDs and NTC temperature sensors; iFixit found its charging coil soldered to the board. Oura Ring 4 is titanium inside and out, with its sensors recessed 0.3 mm into a titanium inner shell, and it is 7.9 mm wide against the Galaxy Ring’s 7.0 mm. The 3D on this page is the Galaxy Ring only.
Does the Galaxy Ring use an NTC temperature sensor?
Samsung calls it a skin temperature sensor and does not say what kind it is. Oura says its Gen3 ring uses negative temperature coefficient (NTC) sensors and lists a digital temperature sensor for Ring 4.
How long does a Galaxy Ring’s battery last?
Samsung gives up to 6 days a charge for sizes 5 to 11 and up to 7 days for sizes 12 and 13. Over its life, iFixit reckons a consumer lithium cell like this is good for at least 400 full cycles; since the cell cannot be replaced, the ring lasts as long as its battery does.
Safety
The ring holds a lithium-polymer cell set right inside its titanium: never cut, drill, pry or pierce it, and never heat it. If it swells, gets hot or grows tight on your finger, take it off with cold water and soap, raise your hand, and if it will not come off, go to a medical professional rather than cutting it yourself. This page shows the inside in 3D so that nobody has to open one.
- Lithium-ion batteries: never bend, puncture or pry a battery with metal. A damaged cell can go into thermal runaway: it smokes, catches fire and can explode. Discharge it below 25% first; if it swells, hisses, smokes or gets hot, stop and move it somewhere safe.
About this guide
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
The ring is our own model of the first Samsung Galaxy Ring (2024) in size 9, built to its published sizes: 18.9 mm across inside and 24.1 mm outside, as a Swisscom size table gives them, and Samsung’s 7.0 mm width, 2.6 mm thickness and 2.7 g (Samsung’s UK page lists sizes 5 to 13, its US page 5 to 15). The ring is drawn plainly in silver titanium, with no Samsung name, logo or marking anywhere but the orientation mark, and its case to Samsung’s figures for a size 11 case, 48.9 × 48.9 × 24.5 mm (the case’s size varies with the ring’s). What is inside follows iFixit’s August 2024 teardown, which had Lumafield scan the ring by CT before cutting it open: a lithium-polymer pouch along one side with the charging coil on top of it, a press connector between them and the board, and everything set in resin that had to be melted and chipped away with a dental pick. Samsung’s own pages give the rest: titanium on the frame only and an epoxy inner surface, three sensor bumps under the orientation mark, an accelerometer, an optical bio-signal sensor and a skin temperature sensor, and a flexible board made in one version a size. Where each part sits round the ring, how long the cell is and how far it bends, its thickness, the chips on the board and the layout inside the case are our estimates.
Where the brief this page was made from differed from the sources, the sources decided. It called the epoxy transparent and medical-grade: Samsung says the inner skin-contact surface is epoxy and names substances it keeps out of the parts that touch skin (phthalates, bisphenol A, nickel and lead among them), but no source we found calls it clear or medical-grade, and since iFixit needed a CT scan to see inside, we draw it dark and opaque, see-through only in the X-ray views. It named an NTC temperature sensor: Samsung calls its sensor a skin temperature sensor and does not say what kind it is (NTC is Oura’s word for its Gen3 ring’s), so the page does not call Samsung’s an NTC. It drew a curved arc battery: iFixit’s scan shows a lithium-polymer pouch running along one side, which we draw following the ring’s curve. The flexible circular board, the sensor bumps (three, from Samsung’s sizing kit page) and the charging coil are kept. Its key trap is kept, with what the sources say: the cell cannot be reached without destroying the ring, and Samsung warns that its battery is a safety risk if damaged and that a stuck ring may be cut only along the orientation mark, where the battery is not.
Samsung gives two sets of battery figures. Its product page rates the cell at 17 mAh in sizes 5 to 7, 18.5 mAh in sizes 8 to 11 and 22.5 mAh in sizes 12 and 13; its charging case page gives the typical capacities, 18, 19.5 and 23.5 mAh, and its support pages give 18 mAh for size 5 and 23.5 mAh for size 13, with up to 7 days a charge (up to 6 days for sizes 5 to 11, its product page says). The 400 cycles are iFixit’s estimate for consumer lithium cells, not Samsung’s figure.
The swelling in step 5 and the smoke in the traps are our picture of them. In September 2025 a YouTuber, Daniel Rotar of ZONEofTECH, reported that his Galaxy Ring’s battery had swollen on his finger before a flight; Tech Advisor reported that it was taken off at a hospital with ice and lubricant, without cutting it, and quoted Samsung calling it an unusual case. Notebookcheck later reported that Samsung found the swelling had been caused by a crack in the internal moulding and saw no wider battery safety risk. The steps for a stuck ring and the cut along the orientation mark are Samsung’s own, for a medical professional; after such a cut, Samsung says, the ring cannot be repaired.
The Oura Ring is built differently. Oura’s Gen3 has a titanium outside and a non-allergenic, non-metallic seamless inner moulding with a BPA-free inner surface, green, red and infrared LEDs, and NTC sensors for temperature; iFixit noted that its charging coil is soldered straight to the board, where the Galaxy Ring’s uses the press connector. Oura Ring 4 is titanium inside and out, with a titanium inner shell, sensors recessed 0.3 mm into it, red, green and infrared LEDs and a digital temperature sensor; it is 7.9 mm wide, about 2.88 mm thick and 3.3 to 5.2 g, against the Galaxy Ring’s 7.0 mm, 2.6 mm and 2.3 to 3.2 g. Neither is drawn here: the 3D is the Galaxy Ring only.
Steps 2 to 6 are X-ray and cutaway views: the real ring cannot be opened, peeled or spread like this, because the epoxy is one cured piece round everything. The 3D runs faster than a real charge, and the field arrows between the coils are only a picture of the power passing across.
Sources: Samsung UK: Galaxy Ring (7 mm wide, 2.6 mm thick; weights by size; titanium on the frame only; accelerometer, optical bio-signal and skin temperature sensors; rated 17, 18.5 and 22.5 mAh; 10ATM and IP68; the crystal-clear charging case), Samsung US: Introducing the Galaxy Ring (made of titanium; 18 mAh in size 5, 23.5 mAh in size 13; up to 7 days; about 80 minutes to a full charge in the case), Samsung Canada: Galaxy Ring charging case (48.9 × 48.9 × 24.5 mm, 61.3 g; typical capacities 18, 19.5 and 23.5 mAh; USB-C, 5 V; case size depends on the ring size), Samsung UK: Galaxy Ring materials and wearing precautions (inner skin contact surface epoxy, outer surface titanium; substances kept out; do not disassemble it; no hair dryers or saunas), Samsung UAE: size and material guide (titanium with epoxy molding), Samsung Ireland: the sizing kit (the three bumps are where the sensors are; sensors towards the palm), Samsung Australia: how to use the Galaxy Ring (the orientation indicator to the palm, and lined up with the marker on the case’s holder; no ultrasonic cleaner), Samsung US: how to remove the Galaxy Ring if it is stuck (soap and cold water, the hand raised; a medical provider cuts along the orientation mark, away from the battery; a second cut about 1 cm aside), Samsung Hong Kong: how to remove the Galaxy Ring if it is stuck (cut along the indicator where the battery is not located), Samsung Australia: safely remove a stuck Galaxy Ring (the battery is a safety risk if damaged; once cut, it cannot be repaired), iFixit: Samsung’s Galaxy Ring revealed (Lumafield CT scan; a lithium polymer pouch with the coil on top; the press connector; resin melted and chipped away with a dental pick; at least 400 cycles; the Oura Gen3’s coil soldered), GSMArena: the Galaxy Ring is non-repairable (the epoxy resin coating melted and chipped away; the PCB sealed into the frame), Android Authority: inside Samsung’s hardware at Unpacked (nine versions of the ring’s flexible circuit board, one a size, carrying its sensors), Swisscom: Galaxy Ring size table (size 9: 24.1 mm outside, 18.9 mm inside, 2.7 g), Tech Advisor: Galaxy Ring swollen battery (Daniel Rotar, September 2025; removed at a hospital with ice and lubricant, not cut; Samsung’s statement), Notebookcheck: Samsung on the Galaxy Ring swelling (a crack in the internal moulding; no wider battery safety risk), Oura: technology in Oura Ring Gen3 (PPG, an NTC sensor for body temperature, a 3D accelerometer), Oura: previous Oura Ring generations (Gen3: titanium with PVD or DLC, a non-allergenic, non-metallic seamless inner molding; green, red and infrared LEDs; NTC sensors), Oura: Oura Ring 4 specifications (titanium inner shell; sensors recessed 0.3 mm; LEDs, a digital temperature sensor, an accelerometer; 7.9 mm wide, about 2.88 mm thick, 3.3 to 5.2 g), Price: Samsung US, Galaxy Ring, from $299.99 new before trade-in (9 November 2026).
The 3D models, drawings and text are our own. Samsung, Galaxy, Galaxy Ring, Oura and Oura Ring are trademarks of their owners, named only to say which device this guide is for; iTakeApart is not affiliated with them.