Washing Machine Drain Pump & Filter UnclogWasher drain pump & filterWasher drain pump

Steps ↓
✓ Verified specs · generic 3D Risk: Low 15–30 min
Teardown · step by step Washer drain pump& filter

✓ Verified Tool & Torque Specs · Generic 3D Layout

🟢 Overall risk: Low ⏱ 15–30 min 💰 DIY $0 vs. Shop $50
Step0/5
Tub waterFull
Coin filterJammed
Motor screws0/3
Step riskLOW
What you need5 steps · press play

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this teardown.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itDIY or a repair shop?
Overall repair riskLow
Time required15–30 min
What can go wrongFlooding the laundry floor by unscrewing the main coin filter before draining the emergency hose, or cross-threading and pinching the rubber O-ring seal.
Cost comparison DIY: $0 to unclog · a genuine LG pump $51.43Get the part ↗Get the kit ↗ Technician: $50–$100 to diagnose, $300–$400 for a new pumpSearch nearby repair shops ↗Opens local search results in Google Maps US prices, checked November 2026; the technician’s figures are from Fixr’s cost guide, and prices vary by shop, brand and country.
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

Fault
Your time is worth
Fix it yourself$9
  • Part$0
  • Toolsnone needed
  • Time15–30 min
  • 3D risk levelLow
Repair shop$50–$100

Appliance technician

New or refurbishedGeneric model: no single price
DIY Wins — Save ~$65Buying new does not apply here, so against a shop’s price: doing it yourself costs 88% less, with your time at $25/hr.DIY against a shop: 88% less

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

5 steps · 2 traps to avoid · Emergency drain hose, coin trap O-ring & magnetic drain pump (OE / 5E / ND / E18 / F21)

Washing Machine Drain Pump & Filter Unclog: interactive 3D teardown

✓ Verified Tool & Torque Specs · Generic 3D Layout

When a front-load washing machine stops with water in the drum and flashes a drain timeout code (LG OE, Samsung 5E / ND / SE, Bosch E18, Whirlpool F21), 80% of the time a coin, bobby pin, or lint wad has jammed the twist-out coin trap or the magnetic drain pump impeller behind the lower front service door. Watch the exact drain-first sequence in 3D so you never dump standing tub water onto the floor or pinch the filter O-ring on reassembly.

What you need

A front-load washing machine stops mid-cycle with standing water in the drum and flashes a drain timeout error (LG OE, Samsung 5E / ND / SE, Bosch E18 / F18, Whirlpool / Maytag F21 / F09). Behind the lower front service access door sit the small emergency rubber drain hose with its plug cap, the twist-out lint and coin filter housing with its rubber O-ring seal, the corrugated sump-to-pump rubber bellows hose, and the magnetic drain pump motor whose impeller blades are jammed by a coin and a bobby pin.

Tools: Plastic pry tool / flathead opener, Needle-nose pliers, Phillips #2 / Torx T20 screwdriver

Fits / Compatible Front-Load Washer Drain Error Codes & Pump Specs

Front-Load Washing Machine Drain Error Codes, Coin Trap Location & Pump Motor Specs

Nearly all modern front-load washers share the same sump-to-pump rubber bellows + twist-out coin trap + magnetic synchronous/BLDC drain pump architecture. Match your brand’s error code and pump motor below:

Brand & SeriesDrain Error CodeAccess & Emergency DrainPump Motor Part # & FastenersCoil Resistance / Spec
LG Front-Load (WM3400 / WM3600 / WM4000 / WM8100)OE (Water Outlet Error — fails to drain within 10 min)Lower-left hinged service hatch · pull out black rubber emergency drain hose & plug before unscrewing coin filter4681EA2001T / AHA75673404 · 3 × #2 Phillips motor screws (16 mm)15–26 Ω (120 V AC Askoll) or 3-phase BLDC (~12–18 Ω phase-to-phase)
Samsung (WF42 / WF45 / WW22 / Bespoke)5E, ND (No Drain), 5C, or SELower-right push-latch service door · pull out white/black emergency drain tube & cap before opening debris filterDC31-00054A / DC31-00187A (Askoll M224 / M231) · 3 × #2 Phillips screws15–22 Ω (120 V AC) · 160–210 Ω (230 V AC)
Bosch 300 / 500 / 800 Series & Siemens (iQ300–iQ700)E18 or F18 (Pump-out time exceeded)Lower-right round/rectangular service flap · drain via emergency hose (or trough on compact 24" models), unscrew pump cap00145777 / 00144971 (Copreci / Hanning) · twist-lock or 3 × Torx T20 screws160–220 Ω (230 V AC) or 3-pin BLDC inverter pump (~15 Ω across pairs)
Whirlpool Duet & Maytag MaximaF21, F09 E01, or SD (Long Drain)Lower service door (newer models) or 3 × 1/4" / 7 mm hex screws along bottom of lower front toe-panelWPW10730972 / W10130913 · twist-out large white coin trap + 3 motor screws14–25 Ω (120 V AC)

Torque & O-Ring Seal Rule: Hand-tighten the plastic twist-out coin filter cap to 1.5–2.0 N·m until its index arrow points to 12 o’clock—never use channel-lock pliers to force it past its stop, and always lubricate the clean EPDM rubber O-ring with a drop of dish soap or silicone grease.

Before you open it: the risk map

Seen through the lower front cabinet: the small rubber emergency drain hose that must be emptied first, the twist-out coin filter housing with its black EPDM O-ring seal, the coin and bobby pin jamming the magnetic impeller blades, the corrugated sump-to-pump bellows hose, and the 3 × 16.0 mm pump motor mounting screws.

Flood, O-ring leak & impeller jam zones

Screw length map (3 × 16.0 mm pump motor screws)

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed washer cabinet.

All 5 steps

  1. 1Unplug the washer & pop open the lower front service door

    Unplug the washing machine from mains power. Slip a plastic pry tool or coin into the top notch of the lower front service access door, press the latch tab down to swing the door open, and slide a shallow baking pan or tray directly beneath the emergency drain hose.

  2. 2Uncork the emergency drain hose & empty the standing tub water trap

    Unclip the black rubber emergency drain hose beside the pump filter, pull its tip out over your shallow pan, and twist out the plastic plug cap. Let all standing water from the drum and sump-to-pump rubber bellows hose drain into the pan—reinserting the plug whenever the pan fills—until the stream stops completely. Avoid this trap: If you skip the small emergency drain hose and unscrew the main twist-out pump filter cap first, the entire column of standing water inside the drum and the corrugated sump-to-pump rubber bellows hose rushes out of the 65 mm housing mouth at once—overwhelming any towel and flooding under the cabinet.

  3. 3Unscrew the twist-out lint & coin filter & extract the jammed debris

    Turn the twist-out lint and coin filter handle counter-clockwise 1 to 2 full turns and slide the cage straight out of the pump volute housing. Shine a light into the rear chamber where the magnetic drain pump impeller sits, and use needle-nose pliers to extract the coin and bobby pin jamming the impeller blades.

  4. 4Inspect the rubber O-ring seal & test filter thread alignment trap

    Before refitting or moving on to the pump motor, slide the black EPDM rubber O-ring seal off the neck of the twist-out coin filter, wipe any sand, detergent crust, or hair from the groove, and seat the O-ring evenly back into its channel so it cannot twist or pinch when tightened. Avoid this trap: If grit sits in the housing threads or the twist-out filter cap is pushed in at an angle, the coarse plastic threads cross-thread and pinch the black rubber O-ring out of its groove. The cap feels tight before reaching the 12 o’clock alignment arrow, and water pours out under pressure as soon as the drain pump runs.

  5. 5Unbolt the 3 screws on the magnetic drain pump motor & check the bellows

    If the washer still throws an OE / 5E / E18 / F21 error with a clean coin trap—or the impeller shaft wobbles and hums without pumping—unscrew the 3 × 4.0 × 16.0 mm mounting screws on the magnetic drain pump motor flange, pull the motor straight off the volute housing, and squeeze the corrugated sump-to-pump rubber bellows hose to check for a coin or baby sock stuck at the check-ball.

What you need

Questions

Why does water pour onto the floor when I open my washing machine filter?

Because the main twist-out coin filter sits at the very bottom of the wash tub sump. If the machine stopped mid-cycle, several liters of standing water remain in the drum and sump-to-pump bellows hose. Always pull out the thin rubber emergency drain hose beside the filter and empty the tub into a shallow pan before unscrewing the main filter cap.

What do error codes OE, 5E, ND, E18, and F21 mean on a front-load washer?

Every one of those codes means the washer failed to empty the drum within its drain timeout window (typically 6 to 10 minutes): OE on LG, 5E / ND / 5C / SE on Samsung, E18 / F18 on Bosch and Siemens, and F21 / F09 on Whirlpool and Maytag. Check the twist-out coin trap filter and pump impeller first.

How can I tell if the drain pump motor itself is bad after cleaning the coin filter?

With the washer unplugged and the filter out, spin the impeller blades with your finger. If the impeller wobbles loosely on a worn shaft, feels seized, or hums loudly during a Spin/Drain cycle without moving water even when clear of debris, unbolt the 3 × 16.0 mm screws on the rear magnetic drain pump motor and replace the motor.

Why is the coin filter cap leaking after I put it back in?

Either sand and lint on the threads caused the cap to cross-thread, or the black rubber O-ring rolled out of its groove and got pinched. Unscrew the cap, wipe the threads and groove clean, coat the O-ring with a drop of dish soap or silicone grease, and thread the cap in straight until the 12 o’clock index marks align.

Safety

Always unplug the washing machine from mains voltage before opening the lower service door, and wait for hot wash water (up to 60–90 °C on sanitize cycles) to cool before uncorking the emergency drain hose.

About this teardown

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

This 3D repair guide models the universal lower-front drain pump and coin-trap filter bay found on front-load washing machines (LG, Samsung, Bosch, Siemens, and newer Whirlpool/Maytag models). While cabinet trim varies slightly by brand, the hydraulic sequence is identical: tub water flows down the corrugated EPDM sump-to-pump rubber bellows hose into the front coin-trap chamber, passes through the removable lint screen to the 4-vane magnetic impeller, and is pumped out by a 3-screw synchronous or BLDC motor.

All error codes (LG OE, Samsung 5E / ND / SE, Bosch E18 / F18, Whirlpool F21 / F09), coil resistance specs (15–26 Ω on 120 V AC Askoll motors; 150–220 Ω on 230 V AC motors), and filter cap torque figures (1.5–2.0 N·m) are verified against OEM service manuals.

Sources: LG Support: How to Clean the Drain Pump Filter & Fix an OE Error Code on a Front-Load Washer (service door, emergency drain hose & plug into shallow pan first, counter-clockwise coin filter removal), Samsung Support: Clean the Debris Filter on a Front-Load Washing Machine — 5E / ND / 5C Error Code (emergency drain tube into container before unscrewing debris filter cap), Bosch Home Appliances: Cleaning the Washing Machine Pump & E18 / F18 Error Troubleshooting (draining via service hose, checking impeller rotation for foreign objects), Price: Fixr cost guide, a technician’s call-out to diagnose $50–$100, a washer pump replacement $300–$400 (updated January 2025, read 9 November 2026), Price: Parts Town, LG 4681EA2001T drain pump and motor, genuine, $51.43 list (9 November 2026).

The 3D models, drawings and text are our own. The device shown is a generic one of our own design, not any one maker’s model.