Fix it yourself, pay a repair shop, or replace it?
- Part$49.99
- Tools$16.95
- Time30–45 min
- 3D risk levelMedium
Appliance technician
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
7 steps · 2 traps to avoid · Whirlpool WP2315539 & WPW10392132 · Top-freezer WRT models
Whirlpool Refrigerator Not Cooling: Evaporator Fan, Defrost Thermostat & Condenser Coils: interactive 3D teardown
When the freezer of a Whirlpool top-freezer stays cold and the fresh-food section warms up, three faults are worth checking before anyone touches the refrigerant: dust on the condenser coils, an iced or worn evaporator fan, and a defrost fault that buries the evaporator in ice. See where each sits on the WRT519SZDM00 (the WRT318FZD’s cabinet) in 3D, and the two traps that ruin the panel or the coil, before you pick up a 1/4-inch nut driver.
What you need
A Whirlpool top-freezer whose freezer stays cold while the fresh-food section warms up can have one of three faults that are reached without opening the sealed refrigerant system: dusty condenser coils behind the base grille, an iced or worn evaporator fan behind the freezer’s rear panel, or a defrost fault that lets ice bury the evaporator coil. The 3D cuts the WRT519SZDM00 (the same cabinet as the WRT318FZD) into two sections on the bench: the freezer’s back wall on its stands, and the front of the machine compartment below it.
Tools: 1/4-inch nut driver, Condenser coil brush, Vacuum with a soft brush tool, Plastic spatula
- Never cut, pierce or bend the refrigerant tubing: a home refrigerator is a sealed small appliance under EPA Section 608, and only a certified technician may open it.
Parts listed for each model on iFixit’s store (November 2026)
Whirlpool top-freezer evaporator fan motor and defrost thermostat by model
Each row is read on iFixit’s store pages for genuine Whirlpool parts; the last column says whether Whirlpool’s dimension guide W11558135A covers the model. Check your own model number on the label inside the fresh-food section before ordering:
| Fridge model | Fan motor WP2315539 | Defrost thermostat WPW10392132 | Dimension guide W11558135A |
|---|---|---|---|
WRT519SZDM00 (the 3D) | Listed | Listed | Yes |
WRT549SZDW01 | Listed | Listed | Its WRT549SZD family |
WRT311FZDW00 | Listed | Listed | Not in this guide |
WRT311FZDW01 | Listed | Not listed | Not in this guide |
WRT318FMDM00 | Not listed | Listed | Yes |
WRT518SZFM00 | Listed | Not listed | Not in this guide |
WRT318FZDW00 / 01 | Not listed | Not listed | Yes (same cabinet) |
No matching series found. Clear the filter to view all compatible models.
Not paired with this model on the pages we read: a defrost heater or a condenser fan motor part number. iFixit lists other Whirlpool defrost thermostats and heaters, but none of them for a WRT model, so none is given here.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the cabinet: the freezer’s rear panel and its hidden screws, the evaporator coil buried in ice with the fan above it and the defrost thermostat on its tube, and below, the condenser coils behind the base grille, the condenser fan and the compressor of the sealed system.
Sealed system, heat, sharp edges and mains zones
- Do not pierce Evaporator tubes: sealed refrigerant system
- No heat Frozen rear panel: no hair dryer or heater
- Sealed system Compressor and lines: certified technician only
- Sharp edges Condenser fan: sharp blades, wear gloves
- Mains supply Power cord: control OFF, then unplug
Screw and clip map (no source gives the screws’ lengths or count)
- 1/4-inch hex-head screws (fan) ×2
- Base grille clips ×2
- Defrost thermostat on its clip
- Hidden 1/4-inch hex-head screws (rear panel) ×4
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed cabinet.
All 7 steps
- 1Check the Airflow control and the vents first
Before taking anything apart, do Whirlpool’s own checks with the fridge still running: the Airflow control on the freezer’s back wall at Recommended, nothing blocking the vents between the freezer and the fresh-food section, and both controls at the factory mid setting. Wait at least 24 hours after any change. A whirring or grinding from the back of the freezer can be ice reaching the evaporator fan (iFixit).
- 2Turn the control OFF, unplug and empty the freezer
Whirlpool’s order: turn the control to OFF, then disconnect the refrigerator from its power source, or switch off its circuit breaker. If you need room behind it, pull the fridge straight out from the wall, since anti-tip brackets hold it at the back (iFixit). Take the food out and lift out the freezer shelf. If an ice maker or dispenser is plumbed in, turn off its water supply and leave its water lines alone.
- 3Pull the base grille off and clean the condenser coils
With both doors open, hold the base grille by its ends, push in at the top and pull up at the bottom (Whirlpool). Vacuum the grille, the open areas behind it and the front of the condenser with a soft brush attachment, loosening the dust with a coil brush; wear safety glasses and do not bend the fins or tubing. Whirlpool says coil cleaning is usually not needed in a typical home, and every six months in a greasy or dusty home or with pets. The black condenser coils can also be reached from the back, through the rear access panel (iFixit).
- 4Free the frozen rear panel and take out its hidden screws trap
Look for ice round the rear panel’s edges or coming out of its air holes (iFixit). If the panel is frozen in place, melt the frost first: Whirlpool’s defrost advice is a bowl of hot water and its steam, never a hair dryer or a heater (iFixit’s guide uses a garment steamer). Pop off the small screw covers, take out the hidden 1/4-inch hex-head screws under them and pull the panel off. If an ice maker is fitted, its cover comes off first: one Phillips screw, and a Molex plug released by pressing its top and bottom tabs (iFixit). Avoid this trap: Whirlpool’s defrost advice rules out a hair dryer or heaters; the steam from a bowl of hot water does the job. Here the hot air is aimed at the frozen panel, and the plastic softens and bulges where it lands: how the damage looks is our own picture, the rule is Whirlpool’s.
- 5Read the frost, then melt the ice: never chip it trap
Even frost over the whole evaporator is normal. Heavy ice around the evaporator and its foam points to a defrost problem, a bad defrost heater or sensor; heavy frost only on the inlet line, such as a frozen upper-right line, points to a low refrigerant charge, which is a technician’s job (iFixit). Let the ice melt with a bowl of hot water and a towel under the coil for the water. Never chip it: Whirlpool warns that an ice pick, knife or other sharp-pointed tool can damage the freezer. Avoid this trap: Whirlpool warns that an ice pick, knife or other sharp-pointed tool can damage the freezer. Here the point slips off the ice and goes through a tube: that puncture and its spray are our own picture, not a source’s. What follows is sourced: opening or recharging the sealed system is work for an EPA Section 608 certified technician, and Fixr puts a sealed-system repair at $800 to $1,200 and a new evaporator coil at $200 to $300.
- 6Turn the evaporator fan by hand, then take out its motor
Turn the fan blade by hand: if it does not spin freely, or the motor was noisy, replace the motor (iFixit). Unhook the fan’s ground wire and unplug its connector, take out the fan’s screws, slide the foam buffers off the chassis lip and pull the housing up and out. On the mat, pull the blade straight off the shaft (it can take real force), pry up the bracket clips and pull the motor straight out (iFixit).
- 7Unplug the defrost thermostat and unclip it from the tube
On Whirlpool top-freezers the defrost thermostat is clipped to the evaporator tubing and the defrost heater runs under the coil (iFixit, on an older model: where they sit on this one is our picture). Pull its connector apart, then ease its clip off the tube by hand, never by levering against the tube. While they are in view, check the heater’s and the thermostat’s connectors for corrosion or looseness (iFixit).
What you need
- 1/4-inch nut driver and a plastic spatula · for the rear panel’s screw covers and hidden screws, and the fan
- Coil brush and a vacuum with a soft brush tool · for the condenser coils behind the base grille
- Bowl of hot water and a towel · to melt the ice and dry the freezer
Questions
Why is my Whirlpool freezer cold but the fridge warm?
With one evaporator fan, it sits in the freezer, and when it fails the freezer can stay cold while the fresh-food section warms up (iFixit). Whirlpool’s first checks are the Airflow control on the freezer’s back wall at Recommended and nothing blocking the vents between the two sections.
How often should the condenser coils be cleaned?
Whirlpool says it is usually not needed in a typical home. In a greasy or dusty home, or with pets, its top-freezer page says every six months; its maintenance list adds that not all condenser coils need cleaning.
What does the frost on the evaporator tell me?
Even frost over the whole coil is normal. Heavy ice around the evaporator and its foam points to a defrost problem, a bad defrost heater or sensor; heavy frost only on the inlet line points to a low refrigerant charge, a technician’s job (iFixit).
Is a sizzling or hissing sound normal?
Yes, during defrost: Whirlpool says it can be water dripping onto the defrost heater during the defrost cycle, a normal part of its running.
Can I recharge the refrigerant myself?
No. Adding or removing refrigerant, attaching gauges or any work that opens the sealed system is work for an EPA Section 608 certified technician, and a home refrigerator counts as a small appliance.
How long until it is cold again?
Whirlpool says to allow 24 hours for the freezer to reach temperature, and to wait at least 24 hours between control changes; it recommends 37 to 40 °F (3 to 4 °C) in the fresh-food section and 0 °F (−18 °C) in the freezer.
Safety
Turn the control to OFF and unplug the fridge before taking off any grille or panel. Never cut, pierce or bend the refrigerant tubing, and never chip ice with a knife or ice pick: only an EPA Section 608 certified technician may open the sealed system. Wear gloves at the evaporator’s fins and the condenser fan, whose sheet metal and blades are sharp.
- Mains power: switch it off and unplug it before you open it: its power supply runs on mains voltage. Never plug it in with a cover off.
About this teardown
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
The 3D is the Whirlpool WRT519SZDM00 top-freezer, which Whirlpool’s dimension guide W11558135A lists with the WRT318FZD family as one cabinet: 29 3/4 in (756 mm) wide, 28 7/8 in (733 mm) deep and 65 7/8 in (1673 mm) tall. It is drawn as two cutaway sections on the bench, the freezer’s back wall on two stands and the front of the machine compartment below it. Only those outside sizes are Whirlpool’s: the freezer’s inner size, the evaporator, the fan’s place above the coil, the defrost thermostat’s and heater’s places, the cover’s hidden screws (their number and places), the condenser, its fan and the compressor are our own picture. No Whirlpool logo or artwork is drawn.
Where the owner’s brief and the sources differ, the sources decide. The freezer’s rear panel on these top-freezers is held by hidden 1/4-inch hex-head screws under small screw covers (iFixit); clips are sourced only for Whirlpool’s side-by-side cover, and no source gives how many screws there are, so the guide counts none. No source gives a defrost time, so there is no “unplug for 24 hours”: the 24 hours here are Whirlpool’s time for the freezer to cool down again. Whirlpool says coil cleaning is usually not needed in a typical home. Whirlpool’s defrost advice rules out a hair dryer or heaters and uses a bowl of hot water and a plastic or wooden spatula; iFixit’s guide frees a frozen panel with a garment steamer; the 3D shows Whirlpool’s way. One Whirlpool page says some base grilles have two Phillips screws; the 3D shows the clip-on grille of its top-freezer instructions.
Only two parts are paired with this model on the pages we could read: the evaporator fan motor WP2315539 ($49.99) and the defrost thermostat WPW10392132 ($8.99), both genuine Whirlpool parts on iFixit’s store, with Whirlpool’s 4210463RW brush at $26.99 and a 1/4-inch nut driver at $16.95. Fixr’s refrigerator repair cost guide gives $120 to $200 for a fan repair and $60 to $100 for coil cleaning; its $100 to $260 thermostat line does not say it is the defrost thermostat, so no shop price is given for that one. The times are iFixit’s: 30 to 45 minutes for its evaporator fan guide, 10 to 20 minutes for its coil cleaning guide and 1 to 3 hours for its cooling troubleshooting guide. The new comparable model is the Whirlpool WRTX3119SW (19.3 cu ft, white), $778 at Shop Appliances, an authorised dealer: the WRT318FZDW itself is marked discontinued there. The two traps’ damage, the warped panel and the pierced tube with its spray, is our own picture; the rules they break are Whirlpool’s, and the sealed-system rules and costs are the EPA’s and Fixr’s.
Sources: Whirlpool dimension guide W11558135A, Top Mount Refrigerator (WRT519SZD and WRT318FZD families: sizes, clearances, 115 V grounded supply, control OFF before cleaning), Whirlpool: Cleaning the Condenser, Top Freezer Refrigerator (base grille off, vacuum with a soft brush attachment), Whirlpool: How and When to Safely Clean the Condenser Coils (unplug, safety glasses, do not bend fins or tubing, 4210463RW brush), Whirlpool: Not Cooling, all refrigerators (base grille: push in at the top, pull up at the bottom; support tabs into metal clips), Whirlpool: Not Cooling, Top Freezer Refrigerator (Airflow control, vents, mid setting, 24 hours between changes, compressor run time), Whirlpool: Too Warm in Freezer Compartment, Top Freezer Refrigerator (Airflow control on the freezer’s back wall), Whirlpool: How to Defrost the Freezer (no ice pick, knife or sharp-pointed tool; no hair dryer or heaters; a bowl of hot water; a plastic or wooden spatula), Whirlpool: What’s Normal, Condensation or Frost (24 hours to reach temperature; 37 to 40 °F and 0 °F), Whirlpool: Sizzling or Hissing Noise, Top Freezer Refrigerator (water dripping on the defrost heater), Whirlpool: Preventative Maintenance for Refrigerators (not all condenser coils need to be cleaned), iFixit: How to Troubleshoot Cooling Problems in a Whirlpool Top Mount Refrigerator (WRT31, WRT51; rear access panel, screw covers and hidden 1/4-inch hex-head screws, frost patterns; 1–3 hours), iFixit: How to Use Diagnostic Mode on a Whirlpool Top Mount Refrigerator (WRT3 and WRT5 controls), iFixit: Whirlpool Refrigerator Evaporator Fan Replacement (ground wire, connector, foam buffers, blade, bracket clips; 30–45 minutes), iFixit: Whirlpool Refrigerator Defrost Heater Replacement, iFixit: Whirlpool Refrigerator Condenser Fan Replacement (sharp sheet metal and blades), iFixit: How to Clean the Condenser Coils in your Whirlpool Refrigerator (10–20 minutes), iFixit: Whirlpool ET18NK No-Frost Refrigerator, Access & Maintenance (defrost heater under the coil, thermostat clipped to the tubing), iFixit wiki: Whirlpool Freezer Not Freezing (one evaporator fan in the freezer, freezer cold and fridge warm, turning the fans by hand, anti-tip brackets), Price: iFixit Store, Whirlpool WP2315539 evaporator fan motor, $49.99, lists WRT519SZDM00 (read November 2026), Price: iFixit Store, Whirlpool WPW10392132 defrost thermostat, $8.99, lists WRT519SZDM00 (read November 2026), Price: iFixit Store, Whirlpool 4210463RW appliance multi-use cleaning brush, $26.99 (read November 2026), Price: iFixit Store, Narwhal driver, the quarter-inch nut driver of guide 207630, $16.95 (read November 2026), Price: Fixr refrigerator repair cost guide (cost guide, updated 29 August 2025): fan $120–$200, coil cleaning $60–$100, sealed system $800–$1,200, evaporator coil $200–$300 (read November 2026), Price: Shop Appliances, Whirlpool WRTX3119SW 19.3 cu ft top-freezer, $778 (read November 2026), Shop Appliances: Whirlpool WRT318FZDW, marked discontinued (read November 2026), US EPA: Section 608 of the Clean Air Act (no intentional venting of refrigerant), US EPA: Section 608 technician certification (Type I for small appliances), US EPA: Section 608 technician certification requirements (attaching gauges, adding or removing refrigerant), 40 CFR 82.152 definitions: small appliance, five pounds of refrigerant or less (Cornell LII).
The 3D models, drawings and text are our own. Whirlpool is a trademark of its owner, named only to say which device this teardown is for; iTakeApart is not affiliated with it.