Windshield Wiper Blades & Washer Pump ReplacementWiper blades & washer pumpWipers & pump

Steps ↓
✓ Verified specs · generic car Risk: Med 45–90 min
Car repair · step by step Wipers & pump

✓ Verified Tool & Torque Specs · Generic 3D Layout

🟡 Overall risk: Medium ⏱ 45–90 min (our estimate) 💰 DIY $32.98
Step0/8
ElectricsKey on
ArmsParked
BladesOld 2/2
WasherOld
Step riskLOW
What you need8 steps · press play

3D Spatial Reconstruction: models are engineered from factual measurements to show the parts, the fixings and the order of the job before you start. Always check the handbook of your own car.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this repair guide.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby garages

Opens local search results in Google Maps for your car and a postcode or city. We do not check, rate or recommend the garages it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itDIY or a repair shop?
Overall repair riskMedium
Time required45–90 min (our estimate)
What can go wrongA bare arm snapping onto the glass, a new blade not clicked home flying off, or the old pump grommet left in to leak
Cost comparison Blades $32.98 a pair; a pump from $26.47 (Civic)Get the part ↗Get the kit ↗ Blades fitted free with purchase (Advance Auto Parts); pump: varies by shopSearch nearby garages ↗Opens local search results in Google Maps US prices read 15 November 2026: Rain-X Vision 26 and 22 in blades at Target, Honda 76806-TBA-A01 at HondaPartsNow and Toyota 85330-04011 ($62.53) at ToyotaPartsDeal. They vary by car and shop.
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

Fault
Your time is worth
Fix it yourself$39
  • Part$32.98
  • Toolsnone needed
  • Time10–20 min
  • 3D risk levelMedium
Repair shopNo sourced figure
New or refurbishedUpkeep: nothing to replace
No verdict: a figure is missingNothing to buy new, and no sourced shop price to compare with: no verdict.

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

8 steps · 45–90 min (our estimate) · J-hook blades & dual-outlet pump · 3 traps to avoid

Windshield Wiper Blades & Washer Pump Replacement: interactive 3D repair guide

✓ Verified Tool & Torque Specs · Generic 3D Layout

Wiper blades and a washer pump changed in 3D on our own generic hatchback: the arms lifted upright over a towel, the old J-hook blades released, the new ones clicked home and locked, a dead washer traced to its pump, the pump levered out of its grommet, a new grommet and pump fitted, and the tank refilled and tested. Press play to watch a step, Explode to spread the pump and the blades, Reassemble for the fitting half on its own.

What you need

Two display pieces of our own generic hatchback stand in the bay: the front of its body with the windscreen, the cowl and two J-hook wiper arms on beam blades, and its right front corner, the wheel off, with the washer reservoir and its pump behind the wheel arch liner. The blades take no tools, only a towel; the pump takes a trim tool, a spanner for the battery clamp, a clean pan, a new grommet and washer fluid to refill.

Tools: Trim tool (wide flat blade)

Example parts, each from its own catalogue page

Example washer pumps, grommets and blades, by the cars their pages list

A part number pairs only with the cars its own catalogue page names (read November 2026). These are examples, not a fit list for every car:

Listed for carPartNumberPrice, Nov 2026
Honda Civic 2016–2023Washer motor, front76806-TBA-A01$26.47
Honda Civic 5-door 2019Washer motor76806-TGG-E01—
Toyota Camry 2018–2024Motor & pump, front85330-04011$62.53
Toyota Corolla 2020–2024Motor & pump, front85330-04011$62.53
Toyota Prius 2016–2018Motor & pump, front85330-04011$62.53
Toyota Corolla 2.0L 2019–2023Inlet packing (grommet)85336-42320$2.25
Toyota Prius 2016–2022Inlet packing (grommet)85336-42320$2.25
J-hook armsRain-X Vision, 26 in—$16.99
J-hook armsRain-X Vision, 22 in—$15.99
Civic, Camry, Corolla, RAV4 (NAPA’s list)Bosch ICON, 26 in26A$35.99

Before you order: the 2019 Civic 5-door’s page lists 76806-TGG-E01, not 76806-TBA-A01; 85330-04011 replaces 85330-04010; and NAPA does not say which side its 26A is for. Our 3D car is our own design, so none of these is its part.

Before you open it: the risk map

Seen through the panels: where a bare arm’s hook lands on the glass, the bonnet edge a hidden arm can chip, the reservoir wall beside the pump, the liner’s clips, the pump’s snap post and the battery’s negative terminal.

Glass, paint and reservoir zones

Connectors, clips and terminals

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed body panels.

All 8 steps

  1. 1Ignition off, lift both arms, lay a towel

    Park, set the parking brake and switch the ignition off, so the wipers cannot start while your hands are on them. Lift the driver’s arm first, then the passenger’s, until each stands upright, at about 90° on most cars, where it should stay on its own. Then lay a folded towel on the glass where the blades rest: should a bare arm fall back, it lands on the towel, not the glass.

  2. 2Release the old blades from their J-hooks trap

    With the arm upright, flip the blade’s locking tab up, tilt the blade’s lower end away from the arm and push the release tab towards the arm, then slide the blade down towards the arm’s base until its adapter clears the hook, and lift it off. That is the Ram’s order for a J-hook. It should come with no force: if it fights you, stop and look again. Leave the bare arm standing upright on its own, the towel under it: without its blade it must never spring back against the glass. Avoid this trap: With its blade off, a wiper arm is a strong spring with a metal hook at its end. Knocked, or let go before it stands fully upright, it snaps back down and the hook strikes the glass. Trico warns that the metal arm might crack the windscreen; Ram, Ford, Kia and Mazda all say not to let a bare arm spring back or slap down. A towel under it and a hand on it are the fix. Where the crack starts and how it spreads are our picture.

  3. 3Click the new blades home, then lower the arms trap

    Take the plastic protector off the new blade’s rubber. Beam blades come with adapters for several kinds of arm; on a J-hook, put the blade under the hook with its locking tab open, feed the adapter into the hook and slide it up until it latches with a click, then fold the tab down until it snaps shut. Check that the connection is locked, and that the blade lines up with the glass, not twisted. Take the towel off, then lower each arm gently by hand, the passenger’s first, so it never slaps down on the windscreen. Avoid this trap: Pushed onto the hook but never slid up until it clicks, its locking tab left open, a new blade still looks fitted. Trico warns that a blade that is not secure can come off while you drive, and then the bare arm sweeps its metal hook across the glass. Slide it up until it clicks, snap the tab shut and check the lock, as Toyota’s manual asks. How it slips out and where it lands are our picture.

  4. 4Test the washer: no spray from either jet

    Switch the ignition on and press the washer. Here nothing comes from either front jet. Look at the reservoir first: its plastic is translucent so the level shows, and here it is full. Do not keep pressing a washer with an empty tank, which Kia warns can damage the pump. With a full tank and no spray, the pump is the likely part (our reading: the makers give no test for it, and a hose or a fuse can stop it too). Chrysler’s service text says the pump cannot be repaired: a failed one is replaced whole. Switch off again.

  5. 5Battery cable off, the liner’s clips and liner out

    Before the pump, disconnect the battery’s negative cable and keep its clamp away from the post, as the Ram’s procedure says. Where the reservoir is reached depends on the car: Tesla goes in through the front wheel arch liner, as here, Saab takes the tank out first, and on some cars the bottle lifts out from above. On a real car the wheel comes off first, with the car on an axle stand, never on the jack alone. Prise the liner’s clips out with the trim tool into the tray, ease the liner’s front part out of the arch, and slide a clean drain pan under the corner.

  6. 6Mark the hoses, unplug the pump, drain the tank

    This is a dual-outlet pump, for a car with a rear washer too: one barbed outlet feeds the front jets, the other the rear, and the motor’s direction picks which. Mark each hose with a strip of tape, F and R, before it comes off: no maker says to, it is our own step. Press the connector’s latch and pull it off the receptacle on top of the motor. Pull the front hose off its outlet and let the tank drain into the pan, then pull off the rear hose. The Ram’s procedure says the drained fluid can be reused.

  7. 7Lever the old pump out, fit a new grommet trap

    The pump is held only by its inlet tip, a tight fit in a rubber grommet at the bottom of the tank, and by a snap post with a light snap fit. Slide the trim tool’s wide blade under the pump’s base and lever it up until the tip comes out of the grommet, taking care not to dig into the reservoir’s wall: Ram uses a trim stick, Saab two flat-bladed tools. Pull the old grommet out and throw it away. Wet the new one with full-strength washer fluid and press it into the hole until its lip sits flat. Avoid this trap: It is tempting to push the new pump into the old grommet and be done. The Ram’s procedure says always to use a new grommet, Saab throws the old one away and Tesla inspects it before the pump goes in; iFixit says the grommet may be the source of a leaking bottle. Here a slow drip runs down the sump onto the floor, and the tank is empty days later. The drip and where it runs are our picture.

  8. 8New pump in, everything back, refill and test

    Push the new pump’s inlet tip into the grommet and press it straight down until it is fully seated and its snap post clicks in. Plug the connector onto the motor, the hose marked F onto the front outlet and R onto the rear. Pan out, the liner back with its clips, the battery cable back on. Refill with washer fluid, never coolant or antifreeze, and a winter fluid in freezing weather. Look at the grommet for a drip, then test: the washer sprays the windscreen and the wipers sweep it wet, and a rear washer sprays from its own switch.

What you need

Questions

Are the driver’s and passenger’s wiper blades the same length?

Often not: Trico says they may be different sizes, and KBB that a rear blade may need another size and design again. Measure the rubber blade, not its metal frame, or look up your car’s sizes; Ford lists its blades’ part numbers in the owner’s manual.

My wipers park under the bonnet. How do I lift them?

Put them in the service position first: on a Kia, within 20 seconds of switching off, hold the wiper switch at single wipe for over 2 seconds; on a 2015 Ford Focus, ignition on, off, then within three seconds hold the lever; on a VW Polo, within 10 seconds press the switch to tip-wipe. Kia warns that pulling a hidden arm forward can chip the bonnet’s paint.

Can I use plain water, or antifreeze, in the washer?

Kia allows plain water only when no washer fluid is to hand, and an antifreeze washer fluid in cold weather. Never coolant or engine antifreeze: Kia says it can badly blur the windscreen, Honda that it can damage the paint. No vinegar mix either, which Honda says can damage the pump.

Why does my windshield washer not spray?

Look in the reservoir first: it is translucent, so the level shows (Kia), and running the pump with the tank empty can damage it. In freezing weather use a winter fluid and warm the glass first. With a full tank and no spray, the pump is the likely part; a failed one cannot be repaired and is replaced whole (Chrysler). A leak under it may come from the grommet (iFixit).

Will a parts store fit my wiper blades?

Advance Auto Parts says it fits wipers for free when you buy them there.

How often should wiper blades be changed?

KBB says at least once a year, and sooner if they squeak, skip or smear; Mazda that blades that no longer clean well are probably worn or cracked.

Safety

Ignition off before you touch the arms, so the wipers cannot start, and a hand on any bare arm: its spring drives the hook onto the glass. Washer fluid is poisonous and can be flammable: keep sparks and flames away, never drink it, and never pour coolant or antifreeze into the washer (Kia).

About this guide

3D Spatial Reconstruction: models are engineered from factual measurements to show the parts, the fixings and the order of the job before you start. Always check the handbook of your own car.

Two display pieces of our own design, not one car: the front of a generic five-door hatchback’s body, cut behind its front doors, with the windscreen, the cowl and two J-hook arms, and its right front corner, its wheel off, with the washer reservoir behind the wheel arch liner. Every size in them is our estimate: the 26 and 22 in blades (Ford’s Motorcraft WW2600A is a 26 in driver’s blade, for the Explorer), the arms, the four liner clips, a tank of about 3.5 litres (Honda lists the Civic’s as 2.5 L), the pump, its grommet and the hoses. The pump follows Chrysler’s service description: a small motor over a rotor pump, the connector on top, two barbed outlets with a valve body for front and rear, and an inlet tip through a rubber grommet that is also the inlet’s filter screen, held by a light snap post.

Where the brief we were given differed from the makers: a screwdriver “tearing the grommet” is not the danger, since Ram and Saab lever the pump out with flat tools themselves and throw the old grommet away; their caution is the reservoir’s wall, so the trap on the pump’s side is the old grommet reused. On Chrysler’s design the inlet filter is part of the grommet, not the pump. Kia allows plain water only when no washer fluid is to hand, and never in cold weather. The towel is a blade maker’s advice (Trico); the car makers’ own words are not to let a bare arm fall or spring back.

Our own pictures, not a maker’s: marking the hoses F and R, the tank draining through the pump’s open outlet (the makers only say to drain it into a clean container), how the glass cracks, how an unlatched blade slips out and where it lands, and the old grommet’s drip. No maker gives a “listen for the hum, check the fuse” test, so this guide gives none. The times are our estimates, and no torque is given: a generic car has none (Tesla’s 3 Nm is for its own reservoir’s bolts).

Sources: Trico: how to replace your windshield wipers (upright arm, towel, J-hook release, click, cracked glass, a blade that can come off), Trico: wiper blade size guide (driver’s and passenger’s sizes, measure the rubber), Mopar: 2022 Ram 2500/3500 owner’s manual, wiper blade removal and installation (J-hook order, locking tab, arm not to spring back), Kia CV1 2023 owner’s manual: front blade and service position (hood paint, chipped or cracked windshield), Kia DL3 2026 owner’s manual: wiper blades, Kia DL3 2026 owner’s manual: wipers and washers (freezing weather), Kia DL3 2026 owner’s manual: operating the washers (empty reservoir, dry glass), Kia DL3 2026 owner’s manual: washer fluid, Kia TK1 2026 owner’s manual: washer fluid (no coolant, flammable, poisonous), Kia MV1A 2026 owner’s manual: washer fluid (translucent reservoir), Mazda 2016 CX-9 owner’s manual: wiper blades (driver’s arm first, lower the passenger’s first), Ford: how do I change my windshield wiper blades, Ford: how do I choose the right windshield wiper blades, Ford: Motorcraft WW2600A wiper blade, 26 in, Explorer, Ford 2015 Focus owner’s manual, service position (manualsdir.com), Toyota 2016 Prius owner’s manual, wiper blade replacement (PriusChat), Honda.ca owner’s manual: washer fluid (no engine antifreeze, no vinegar mix), VW Polo Mk5 wiper service position (workshop-manuals.com), Dodge Ram windshield washer pump removal and installation (workshop-manuals.com), Chrysler washer pump description (unofficial service-text mirror), Saab WIS 9-4X 2011: windshield washer pump replacement, Tesla Model 3 service manual: windshield washer pump, Tesla Model 3 service manual: washer pump grommet, iFixit: Mercedes W123 windshield washer fluid bottle and pump replacement, DRiV Parts Matter: windshield wiper connectors, Price: KBB, how to change wiper blades (blades from about $8 to over $30 each; 31 July 2026, read November 2026), Bosch ICON installation sheet (adapters for 16, 19 and 22 mm arms; Canadian Tire), True Value: Rain-X Latitude 26 in (two connectors for eight arm types), Price: NAPA, Bosch ICON 26A, $35.99 (read November 2026), Price: Target, Rain-X 26" Vision wiper blade, $16.99 (read November 2026), Price: Target, Rain-X 22" Vision wiper blade, $15.99 (read November 2026), Price: Target, Rain-X 0 Degree washer fluid, 1 gal, $4.99 (read November 2026), Price: Advance Auto Parts store page, wipers installed free when bought there (read November 2026), Price: HondaPartsNow, Honda 76806-TBA-A01 washer motor, $26.47 (2016–2023 Civic; read November 2026), HondaPartsNow: 2019 Civic washer pumps (76806-TGG-E01 for the 5-door), Price: ToyotaPartsDeal, Toyota 85330-04011 motor and pump, $62.53 (read November 2026), Price: ToyotaPartsDeal, Toyota 85336-42320 inlet packing, $2.25 (read November 2026).

The 3D models, drawings and text are our own. The 3D car and component models are unbadged generic reconstructions of our own design, not any one maker’s vehicle. Trico, Rain-X, Latitude, Vision, Bosch, ICON, Honda, Civic, Toyota, Corolla, Camry, Prius, RAV4, Kia, Mazda, Ford, Motorcraft, Explorer, Focus, Ram, Chrysler, Saab, Tesla, VW, Polo, KBB, DRiV, NAPA, Target and Advance Auto Parts are trademarks of their respective owners, named strictly in text to indicate mechanical compatibility and fastener/part specifications (nominative fair use); iTakeApart is not affiliated with or endorsed by any vehicle manufacturer.