Fix it yourself, pay a repair shop, or replace it?
FaultWorn-out 12 V battery
- Part$189.99
- Toolsnot priced
- TimeNo sourced figure
- 3D risk levelMedium
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
8 steps · 2 traps to avoid · negative off first · BCI Group 35 in 3D
Car Battery Replacement: interactive 3D repair guide
✓ Verified Tool & Torque Specs · Generic 3D Layout
A car’s 12 V battery changed in 3D, in a generic engine bay of our own design: the engine off and the positive cable marked, the negative cable off first and then the positive, the hold-down bar off, the old battery lifted straight up and out, the tray and the clamps cleaned of corrosion, the new battery in and held down snug, then the positive on first and the negative last. Press play to watch a step, Explode to lift the battery, the clamps and the hold-down apart, and Reassemble for the new battery going in.
What you need
A generic car of our own design: the corner of its engine bay with a 12 V lead-acid battery, a BCI Group 35 (six cells, posts on top, the negative on the left and the positive on the right of the near side), held down by a steel bar on two hooked rods. Read the car’s owner’s manual first, as VARTA and AAA both advise: it names the battery group and any torque figures, and a few cars need a dealer after the battery has been disconnected.
Tools: Spanner and a socket with ratchet, Battery terminal brush
- A memory saver plugged into the power outlet first keeps the radio presets and other settings while the battery is out (AAA).
Battery groups, sizes and terminal layouts
BCI Battery Groups: Maximum Sizes, Terminal Layouts and Equivalents
From the Battery Council International’s group size chart (October 2023): each group’s maximum size, its terminal layout figure and its DIN, EN or JIS equivalents. Match the group of the battery your car came with:
| BCI group | Max size (L × W × H) | BCI layout figure | DIN / EN / JIS | Example (NAPA) |
|---|---|---|---|---|
Group 35 (the 3D) | 230 × 175 × 225 mm | Fig. 11: − left, + right, near side | JIS 55D23L, 65D23L, 70D23L, 75D23L, 80D23L | BAT 7535 flooded, 550 CCA |
Group 48 (H6) | 278 × 175 × 190 mm | Fig. 24 | DIN H6 / EN LN3; group 148 is a 48 with the terminals reversed | BAT 7548 flooded, 680 CCA |
Group 47 (H5) | 242 × 175 × 190 mm | Fig. 24 | DIN H5 / EN LN2 | — |
Group 49 (H8) | 353 × 175 × 190 mm | Fig. 24 | DIN H8 / EN LN5 | — |
Group 24F | 273 × 173 × 229 mm | Fig. 11F | — | — |
Group 51R | 238 × 129 × 223 mm | Fig. 11 | JIS 46B24L family | — |
Group 65 | 306 × 192 × 192 mm | Fig. 21 | — | — |
OE JIS S34B20L | — | — | Toyota Prius: Remote Venting | — |
OE JIS 46A24L | — | — | Mazda Miata: Remote Venting | — |
No matching series found. Clear the filter to view all compatible models.
Same group, same layout: BCI’s group sets the battery’s size, its hold-down and where its terminals are (AAA). Many cars accept more than one group, so check the manual’s list (VARTA). A battery in the boot or the cabin may need remote venting: fit one designed for the vehicle (Toyota, BCI).
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the battery’s case: its six cells in a row, the negative post on the left and the positive on the right, the hold-down bar on its two rods, and the inner wing a spanner on the positive must never touch.
Short-circuit and hydrogen zones
- No tool across Positive post: no metal from here to the body
- Body = negative Inner wing: the battery’s negative while connected
- Hydrogen Cells give off hydrogen: no sparks or flames
Nuts to undo, in this order
- Hold-down nuts: after both cables ×2
- Negative clamp nut: off first
- Positive clamp nut: off second
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed battery case.
All 8 steps
- 1Engine off, key out, positive cable marked
Park on level ground in Park (or first gear) with the parking brake on, the engine off, the key out and the lights and accessories off, and let the engine cool. Put on eye protection and gloves, and take off rings, watches and any other metal jewellery. Then wrap a strip of painter’s tape round the positive (+, red) cable, so the new battery cannot go in the wrong way round.
- 2Negative cable off first trap
Loosen the nut on the negative (−, black) clamp, spread the clamp a little and lift it straight up off the post. Never pry a stuck clamp off: AAA says that can damage the battery’s case and internal connections, so use a terminal puller. Lay the cable aside, or cover its end with a rag, so it cannot touch the post again. Undo it at the battery, not where it bolts to the body: Toyota warns that a negative loosened there can touch the positive and short. Avoid this trap: Start with the positive and let the spanner on its nut swing onto the inner wing, and the battery shorts through the spanner. AAA warns that starting with the positive could cause a dangerous electrical short, and that a metal object across the positive and ground can cause explosive sparks or serious burns. The UK HSE says an uninsulated metal spanner across a battery gets very hot very quickly, and if the battery explodes, molten metal can burn and set its gases alight. Take the negative off first and put it back last: then a spanner on the positive has nothing to short to.
- 3Positive cable off second
Lift the red insulating cover off the positive (+) clamp, if it has one, loosen the clamp’s nut, spread the clamp and lift it off the post, and lay the cable down clear of the battery. With the negative already off, the spanner can no longer short the battery to the car’s body: VARTA takes the ground off first for exactly this, to avoid accidental grounds with tools.
- 4Hold-down bar off
Undo the nut on each of the hold-down’s two rods, lift the bar off the battery and unhook the rods from the tray. Cars hold their batteries in different ways: VARTA names a top bar or top frame, a bottom recess clamp and a bottom ledge clamp. If a heat shield covers the battery, it comes off here and goes back on later (AAA). Keep the nuts, the bar and the rods together.
- 5Lift the old battery out of its tray
Lift the battery straight up and out, keeping it upright so no acid spills, and never by its posts (OPTIMA). It is heavy: NAPA lists its Group 35 flooded battery at 15.4 kg, and the UK HSE says to share a lift like this. Dropped, the case can crack and spill acid (AAA). Set it down upright, clear of where you work.
- 6Clean the tray, hold-down and clamps
Scrub the tray, the hold-down and the cable clamps with a wire brush and a solution of baking soda and water, which neutralises the corrosion, then rinse and dry them. The sources mix it differently: AAA says half and half, Interstate one part baking soda to five of water. Then check that the tray and the hold-down are sound and free of corrosion (VARTA).
- 7New battery in, hold-down snug trap
Check the new battery is the same BCI group as the old one, with a cold cranking amps (CCA) rating no lower than the carmaker’s (AAA). Set it level in the clean tray with nothing under it and its posts towards the cables, the positive post, the larger one, by the red cable. Hook the rods in, lay the bar across and tighten the nuts until the battery is snug, without distorting or cracking the case. Where the manual gives no figure, VARTA’s for a top bar is 3.4–5.6 N·m (30–50 in-lb). Avoid this trap: Left off, or done up loose, the hold-down cannot stop the battery moving as the car drives. AAA says vibration causes physical breakdown of a battery’s internal parts, and Interstate calls vibration the most common way to kill a car battery. OPTIMA: with no hold-down, only the cables hold the battery, pulling on them can damage the terminal connections, and at worst a loose battery’s terminals touch a metal surface. Hook the rods in and tighten the bar until the battery is snug, and no tighter.
- 8Positive on first, negative last
Put the positive clamp on its post first, press it down and tighten the nut: OPTIMA gives 6–8 N·m for an SAE post and warns not to over-tighten. Coat the terminal with dielectric grease or petroleum jelly (iFixit), or fit anti-corrosion washers (AAA), and fold the red cover back down. The negative goes on last, the same way. Then take the tape off, start the engine and check the lights, the radio and the other electrics.
What you need
- A new battery of the same BCI group · with a CCA rating no lower than the carmaker’s (AAA)
- A spanner and a socket with ratchet · the sizes your clamp and hold-down nuts take
- A terminal brush, a wire brush, baking soda · to clean the clamps, the tray and the hold-down
- Eye protection, gloves and painter’s tape · and dielectric grease or petroleum jelly
Questions
Which battery cable comes off first?
The negative (−, black): it comes off first and goes back on last, and the positive goes back on first. Kia, Hyundai, Interstate, AAA and the UK HSE all say so. The reason: with the negative off, a spanner on the positive that touches the car’s body can no longer short the battery (AAA, VARTA, HSE).
Will I lose my radio presets and settings?
Often. Kia lists the auto up/down windows, the trip computer, the climate control and the sunroof to reset; Hyundai adds the power liftgate, cluster settings, integrated memory, the clock and the infotainment. A memory saver in the power outlet avoids most of it (AAA), a few cars need a dealer visit, and Ford’s battery management needs 8 hours with the key off to relearn the new battery.
How do I pick the right replacement battery?
The same BCI group number as the original, which sets its size, its hold-down and where its terminals are, with a CCA rating no lower than the carmaker’s; higher is fine if it fits. Buy fresh stock, no more than 90 days old (AAA). If the car came with an AGM battery, Kia and Hyundai send owners to their dealers to replace or service it.
How do I clean corroded battery terminals?
With a solution of baking soda and water and a stiff or wire brush, then rinse and dry: AAA mixes it half and half, Interstate one part baking soda to five of water. Never paint the terminals (VARTA). Afterwards, a thin coat of dielectric grease or petroleum jelly (iFixit), or anti-corrosion washers (AAA).
What do I do with the old battery?
Recycle it: it contains lead and acid (Kia, Hyundai). The store refunds its core deposit when it comes back, deposits that state laws often require (Interstate). Advance Auto Parts and AAA recycle batteries free, and battery suppliers and scrap dealers take them too (HSE).
My battery is in the boot or the cabin: is anything different?
Yes. Toyota’s 2011 Prius keeps its battery in the luggage compartment and says to fit a 12 V battery designed for the vehicle, or hydrogen can get into the cabin and cause a fire or an explosion. BCI marks the Prius’s and the Mazda Miata’s original batteries for remote venting, and OPTIMA says never to fit a battery in a sealed compartment with no ventilation.
Safety
A car battery holds sulphuric acid and gives off hydrogen: wear eye protection and gloves, keep flames, sparks and cigarettes away. Take the negative off first and put it back last, never rest a metal tool on the battery, and take off rings and watches. It is heavy: lift it upright, never by its posts, and share the lift. If acid gets in your eyes, flush them with clean water for at least 15 minutes and get medical help. Keep batteries away from children.
- Car batteries: a lead-acid battery gives off explosive hydrogen. No sparks, flames or smoking near it, eye protection on, and the last jump lead clamped to bare metal away from the battery.
- Engine off: switch the engine and the fan off and take the key away before you reach behind the dashboard or under the bonnet.
- Hot parts and fumes: brakes, exhausts and engines stay hot long after a drive, and a running engine fills a closed garage with carbon monoxide: let parts cool, and keep the door open.
About this guide
3D Spatial Reconstruction: models are engineered from factual measurements to show the parts, the fixings and the order of the job before you start. Always check the handbook of your own car.
The car is a generic one of our own design: the corner of an engine bay on a stand, with a BCI Group 35 flooded battery drawn to BCI’s maximum size (230 × 175 × 225 mm), its posts where BCI’s figure 11 puts them, and a steel top bar on two hooked rods. Where the battery sits, the shape of the bar and the rods, the cables’ routes and every nut are our picture. The positive post is drawn larger than the negative, as VARTA and AAA describe it, but with no size printed: no source we read gives the posts’ diameters.
No size is given for the clamp or hold-down nuts, because they differ by car: VARTA says only to use the proper size box or open-end wrench. No time is given for the job either, as no source we read publishes one. The torques are the battery makers’ own for when the car’s manual has none: OPTIMA’s 6–8 N·m for an SAE post, and VARTA’s 30–50 in-lb for a top bar, which is 3.4–5.6 N·m in our conversion.
The traps: the spanner on the positive shorting to the inner wing while the negative is still on, after AAA, VARTA and the UK HSE; and the hold-down left off, after AAA, OPTIMA and Interstate. The spark, and how far a loose battery rocks in its tray, are our picture. This is not the jump-start guide: there the battery stays in the car and jumper cables are clamped on; here it comes out and a new one goes in.
Prices are US ones, read in November 2026: NAPA’s Group 35 flooded battery at $189.99 on its own page, and Jerry’s cost guide for a professionally fitted battery, $268–$368 with the old one’s disposal. Advance Auto Parts fits a new battery free, for most vehicles, when it is bought there. The Fix vs. Replace card weighs NAPA’s battery against Jerry’s range and counts no time for your own work, since none is sourced.
Sources: Kia owner’s manual (2025): battery care, the negative removed first and installed last, AGM batteries, what to reset afterwards, Hyundai owner’s manual: battery, hydrogen, AGM service and the settings to reset, Toyota 2011 Prius owner’s manual, pp. 448–452: battery warnings, the negative at the body end, a battery in the luggage compartment (manualsdir copy), Ford 2013 F-150 owner’s manual, p. 326: the battery management system’s 8 hours to relearn (manualsdir copy), iFixit: car and truck battery replacement (Toyota Corolla), iFixit: 2003–2007 Honda Accord battery replacement (the cross-bar hold-down), OPTIMA: safety and installation tips (terminal torque, lifting, hold-down), OPTIMA: “Loose Car Battery?” (hold-downs), VARTA: step one, select the right battery, VARTA: step two, remove the old battery, VARTA: step three, install the new battery (hold-down torques, polarity), VARTA: battery safety and handling, Interstate Batteries: FAQ (order, baking soda, hold-downs), Interstate Batteries: why did my car battery die? (vibration, corrosion), Interstate Batteries: the refundable core deposit, AAA: Make Sense of Car Care, Batteries (brochure), AAA Club Alliance: a guide to removing your car battery, AAA Club Alliance: how to select and change your car’s battery, AAA (ACG): replacing your car battery (memory saver, painter’s tape), AAA Club Alliance: mobile battery service (free recycling), UK HSE INDG139: using electric storage batteries safely, Battery Council International: group sizes, layouts and DIN / EN / JIS charts (October 2023), Price: NAPA The Legend Professional BCI No. 35 flooded battery, 550 CCA (BAT 7535), $189.99, 34 lb (read November 2026), Price: NAPA The Legend Professional BCI No. 48 (H6) flooded battery, 680 CCA (BAT 7548), $189.99 (read November 2026), Price: Jerry cost guide, battery replacement: professionally installed $268–$368 with disposal (read November 2026), Advance Auto Parts store page: free battery installation with a new battery, for most vehicles; free testing and recycling (read November 2026).
The 3D models, drawings and text are our own. The car shown is a generic one of our own design, not any one maker’s model.