Fix it yourself, pay a repair shop, or replace it?
Plumber
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
9 steps · Flapper · float · fill valve · siphon · 4 traps to avoid
How a toilet works: the flush mechanism in interactive 3D
Illustrative 3D Concept Model — Generic Layout
A see-through toilet in 3D, with its water in cyan: the handle and chain lift the flapper, the tank pours through the rim and the jet, the level passes the trapway’s crest and the siphon empties the bowl, with the gurgle at the end. Then the float falls, the fill valve fills the tank and the refill tube tops up the bowl. Press Flush to run it yourself, Explode to spread the tank’s parts, Reassemble to refit them and test.
What is inside
A close-coupled toilet of our own design, see-through and side-on, with its middle plane facing you. In the tank: the handle and its lever, a chain, the flapper on the flush valve’s seat, the overflow tube, the fill valve with its float ball on an arm, and the refill tube. In the china below: the rim with its holes, a siphon jet at the bottom of the bowl, and the S-shaped trapway. The water is in cyan, and it does the work: there is no pump and no motor. Press Flush to run a whole cycle whenever you like.
- Press Flush (N) on any step: the handle, the flapper, the levels and the counters run on their own clock. Press it again mid-cycle and it does what a real toilet does.
Before you open it: the risk map
Seen through the closed toilet: the lid and the tank bolts that break, the stop valve to shut first, the flapper’s seat, the water seal at the crest, and the three things that set how it flushes.
Before you lift the lid
- Breakable Lid: heavy china, two hands
- Do not overtighten Tank bolts: china cracks
- Seal Flapper seat: no in-tank cleaners
- Shut first Stop valve: shut it first
- Water seal Crest: the seal against sewer gas
What to set right
- Chain: 1 or 2 links of slack
- Refill tube: clipped, not pushed in
- Water line: 25–50 mm under the top
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed toilet.
All 9 steps
- 1The handle lifts the flapper trap
Pressing the handle swings its lever up inside the tank. The lever takes up the chain’s bit of slack and lifts the flapper, the rubber cap that the weight of the water has been holding down on the flush valve’s seat. The handle only has to start it: lifted far enough, the flapper carries on by itself. Avoid this trap: With a long loop of slack in the chain, the lever’s swing is nearly used up before the chain goes tight. The flapper lifts only a little, not far enough to float, and falls back as soon as the handle comes up. A little water runs into the bowl, some of it spills over the crest, and the long leg never fills, so there is no siphon: a weak flush, or none, unless you hold the lever down. The usual advice is to leave only 1 or 2 links of slack with the flapper shut. How far the flapper lifts here is our picture.
- 2The flapper floats open and the tank pours out
The flapper is buoyant, so once it is lifted it floats, holding itself open with no help from the handle. The tank’s water drops through the 50 to 75 mm hole in the seat, a whole tank in about three seconds, and on through passages in the china: round the rim and out of the holes under it, and down to a bigger hole at the bottom of the bowl, the siphon jet, which shoots straight at the trapway’s mouth.
- 3The bowl rises past the crest and the trapway fills
The trapway climbs from the bottom of the bowl to a crest, then drops away to the drain. At rest the water stands level with the crest’s underside: add a little and the extra just runs over. But the tank’s water is arriving faster than it can spill, so the level climbs up the bowl, past the crest, and the water pours over and down the long leg, pushing the air out ahead of it. When the tube is running full, the siphon starts. That is why a flush has to be fast.
- 4The siphon empties the bowl, and the flapper drops trap
A full tube is a siphon. The water falling down the long leg pulls what is behind it up the short leg and over the crest, so the bowl’s level sinks below the crest, which it could never do by itself, with air pressure pushing on its surface. Meanwhile the tank is running out. With too little water left to float it, the flapper falls back onto its seat and closes it. The float has come down with the level, and the fill valve has been open since just after the flush began. Avoid this trap: With no slack, the chain holds the flapper up by a few degrees even with the handle at rest. At the end of a flush it cannot reach its seat: water keeps running under it into the bowl, the tank never quite fills, and the fill valve never shuts. Give the chain 1 or 2 links of slack, then flush with the lid off and watch the flapper close its hole completely. The gap is drawn larger than life so you can see it.
- 5Air breaks the siphon: the gurgle
The bowl has sunk so low that air reaches the trapway’s mouth. It rushes in along the short leg, the column of water breaks up and goes over the crest and away, and that is the gurgle at the end of every flush. The siphon is over. A little water is left in the bottom of the bowl, far below the crest.
- 6The fill valve refills the tank and the bowl trap
With the float down, the fill valve is wide open and sends water two ways. Most goes straight into the tank. The rest goes through the thin refill tube, down the overflow tube, and out of the rim’s holes into the bowl, until the water stands at the crest again. That water in the bend is the seal that keeps sewer gas out of the room. The 3D runs this part several times faster: a real tank takes about 30 to 60 seconds. Avoid this trap: Rubber wears out. A flapper that no longer seals lets water seep past it into the bowl, with no sound and no sign. The level falls until the float opens the fill valve, the tank tops up, and it starts again: the ghost flush, a toilet that runs for a moment on its own. It can waste thousands of gallons a year, by the US EPA’s reckoning. To test for it, put a few drops of food colouring or a dye tablet in the tank, wait 10 minutes without flushing, and look in the bowl: colour there is a leak. Then flush so the dye does not stain, and replace the flapper; WaterSense suggests at least every five years. The leak is speeded up here: a real one takes far longer.
- 7The float rises and shuts the valve trap
As the tank fills, the float ball rises on its arm, and at its set level the arm shuts the fill valve. The water line stays 25–50 mm under the top of the overflow tube. That tube is the toilet’s safety: if a valve were ever to jam open, the water would run down it into the bowl and not onto the floor. The toilet is silent again, the bowl full to its crest, the tank ready for the next flush. Many newer fill valves use a float cup sliding on the valve’s tower in place of a ball on an arm; the idea is the same. Avoid this trap: Set too high, the float is still not up at its shut-off point when the water reaches the top of the overflow tube. The tube takes all the water that comes in, the valve never shuts, and the toilet runs on with its water going straight to the bowl and over the crest. Lower the float until the water stops 25–50 mm under the tube’s top: on a ball float, by bending the arm down a little, on a cup, by its adjuster. The height of the valve’s shut-off here is our picture.
- 8The bucket test: a slow pour does nothing, a fast one flushes
The bowl does not need the tank at all, and a bucket shows why the tank is there. Pour slowly and nothing happens: the extra runs over the crest in a thin film with air still above it, and the level hardly rises however long you pour. A cup at a time, 25 cups, would be the same. Now tip in about 7 litres, about 2 gallons, all at once. It comes in faster than it can spill, the level rises past the crest, the tube fills and the bowl flushes, with the gurgle at the end. With no refill tube working here, a last gentle pour brings the water back to the crest. A house’s water pipe could never deliver water that fast: that is the tank’s job, to save it up for 30 to 60 seconds and let it all go in about 3.
- 9The parts a repair replaces
What wears out is in the tank, and most of it comes out by hand. Lift the lid off with both hands and set it down flat somewhere safe. Shut the stop valve and flush: with no water coming in the tank stays empty. Sponge out the last of it. Then the refill tube unclips, the handle and lever come out of the front wall, the flapper slips off its two ears with its chain, the float and its arm unscrew, and the fill valve comes out through the floor once its shank nut and supply are undone. The flush valve and the overflow tube stay: they come out only with the tank off the bowl.
What is in it
- Handle, lever and chain · a short press, 1 or 2 links of slack
- Flapper on the flush valve’s seat · floats open once lifted
- Overflow tube · the safety, and the bowl’s way in for the refill
- Fill valve and float ball · open while the float is down
- Refill tube · tops the bowl back up to the crest
- Rim holes and siphon jet · wash the bowl and aim at the trapway
- S-shaped trapway · the water seal and the siphon
Questions
How does a toilet flush work?
The handle lifts the flapper and the tank’s water pours into the bowl in about three seconds. The level rises past the trapway’s crest, water fills the tube, and the full tube works as a siphon that pulls the bowl empty. When air reaches the tube the siphon breaks with a gurgle, and the fill valve refills the tank and the bowl.
Why does pouring water slowly into a toilet not flush it?
Poured slowly, the extra water just runs over the trapway’s crest with air above it, so the level hardly rises and the tube never fills: no siphon. Even 25 cups, one at a time, do nothing, while about 2 gallons poured fast flushes.
What makes the gurgle at the end of a flush?
Air. Once the bowl is low enough, air reaches the trapway’s mouth and rushes into the tube, breaking the column of water and ending the siphon.
Why is my toilet running all the time?
Usually one of three things: a flapper that no longer seals, a chain so short it holds the flapper off its seat, or a float set so high that the water runs down the overflow tube. Lift the lid and look: water going down the overflow tube points to the float; water still going through the seat points to the flapper or the chain.
What is a phantom or ghost flush?
The tank topping itself up with nobody near it, usually because a worn flapper lets water seep into the bowl until the float opens the fill valve. To test: a few drops of food colouring in the tank, 10 minutes without flushing, and colour in the bowl means a leak.
How much slack should a toilet chain have?
A flapper maker’s advice is 1 or 2 links with the flapper shut. With much more the flapper barely lifts and the flush is weak; with none it cannot seal and the toilet runs on.
How high should the water be in the tank?
Under the top of the overflow tube: the usual advice is 25–50 mm below it, and many tanks have a mark on the wall. Follow the mark or your valve’s instructions if it has them.
Can I flush a toilet when the water is off?
Yes: a bucket with about 2 gallons, about 7 litres, poured into the bowl quickly does the tank’s job. Add a little more gently afterwards to bring the water back up to the crest.
Should I use tablets in the toilet tank?
Toilet makers warn against in-tank cleaners: products with chlorine can seriously damage the tank’s fittings and lead to leaks.
Safety
Shut the stop valve before you work in the tank. The lid and the tank are heavy vitreous china, which breaks or chips if it is overtightened or handled carelessly, and broken china is sharp: lift with both hands, put them down flat, and never force a nut. Do not put cleaning tablets in the tank: toilet makers warn that chlorine products can seriously damage its fittings and cause leaks.
About this guide
3D Spatial Reconstruction: a generic model of our own design, built from published facts to show how the parts work together. Real ones differ by maker and model: always check your own before you open or adjust it.
The toilet is a generic close-coupled gravity toilet of our own design, not any maker’s: about 700 mm long, 380 mm wide and 690 mm high, with a 50 mm trapway and about 6 litres a flush, the 1.6 gallons US rules have required since 1994. We have used a ball float on an arm, the classic arrangement; most fill valves sold now have a float cup sliding on the tower instead, and work the same way. Our jet is fed from the rim, as many are, and the passages in the china are simplified. Some toilets, common outside the Americas, flush by the water’s force with no siphon at all (washdown); this one is the siphon type.
Nothing here is a fluid simulation or a measurement. The levels and the tube’s fill come from a small model of our own, sized to the sources’ figures: most of the tank in about 3 seconds, a slow pour that only spills, a fast one that fills the tube. The refill is speeded up several times, because a real tank takes about 30 to 60 seconds, and the worn flapper’s leak far more than that. The flapper’s gap in the chain trap is drawn larger than life. The flapper is shown dropping before the gurgle, as the sources describe it: the tank has gone before the bowl has.
Sources: HowStuffWorks, the bowl siphon (a cup at a time, even 25 cups, does nothing; about 2 gallons, 7.6 L, poured fast flushes; air entering gives the gurgle), HowStuffWorks, the flush mechanism (a house pipe is too slow; 30 to 60 s to fill; dumped in about 3 s; chain, floating flush valve, 2 to 3 inch hole, rim holes, siphon jet), HowStuffWorks, the refill mechanism (float, valve, refill tube down the overflow tube, overflow as the safety), Kohler, how a toilet flushes (the surge fills the trapway and pushes the air out; the siphon; air re-entering stops it; the float and the fill valve), Family Handyman, how a toilet works (water over the top of the trapway; rim jets and siphon jet; the float drops and the flapper drops as the tank empties), This Old House, how a siphon works (short and long legs; a sudden flow starts it; air breaks it; the jet), Wikipedia, flush toilet (a buoyant flapper; siphon and washdown bowls; the water seal against sewer gas; 1.6 gallons since 1994), Korky, slow or weak flushing toilets (a chain too loose: weak flush; too tight: running; 1 or 2 links of slack; a float too high overflows down the tube), US EPA WaterSense, Read This Before You Flip Your Flapper (rubber wears, replace at least every five years; the dye test; chain too tight or too loose), US EPA, Fix a Leak Week (a worn flapper can flush by itself or leak silently, thousands of gallons a year; food colouring, 10 minutes), Oatey, how to stop ghost flushing (water leaking from tank to bowl wakes the fill valve; a faulty flapper is the most common cause), Fixing a toilet chain, a housing help page (too short and it will not close; too long and you may have to hold the lever), Fluidmaster, toilet repair guide (a tank slow to fill points to the fill valve or the flapper), WaterSafe, how to stop a running toilet (water 1 to 2 inches below the overflow; a float too high runs on; a worn flapper leaks), HomeTips, adjusting a fill valve (a ball float’s arm is bent, a cup’s screw turned; the refill tube clipped, not pushed down), Kohler, installation sheet (turn the water off; no in-tank cleaners: chlorine products can seriously damage the tank’s fittings), Kohler, installation instructions (vitreous china breaks or chips if nuts are overtightened or it is handled carelessly; keep rim holes clean), Prices: Noel’s Plumbing Supply, Fluidmaster 502 flapper $11.47; PlumbingSupply.com, Fluidmaster 400A fill valve $18.27 (November 2026), Price: PlumbingSupply.com, Fluidmaster fill valves, Price: Fixr cost guide, toilet flapper replaced by a plumber, $60–$120 (updated January 2025, read 9 November 2026).
The 3D models, drawings and text are our own. The device shown is a generic one of our own design, not any one maker’s model.