Fix it yourself, pay a repair shop, or replace it?
FaultClogged cabin air filter
- PartNo sourced figure
- Toolsnone needed
- Time5–10 min
- 3D risk levelLow
Garage
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
6 steps · No tools · 2019–2026 Toyota TNGA (E210 / XA50 / XV70) · Part #CF12157
2019–2026 Toyota Corolla, RAV4 & Camry (TNGA) Cabin Air Filter Replacement: interactive 3D repair guide
Starting with the 2018 Camry (XV70) and 2019 Corolla (E210) and RAV4 (XA50), Toyota switched its TNGA lineup to a slightly smaller 215 × 184.5 × 27 mm cabin filter (#CF12157 / OEM 87139-58010 or 87139-0E040) held inside a reusable white plastic carrier tray behind a removable glovebox shelf divider. Watch every step in 3D below.
What you need
On 2018–2026 Toyota and Lexus vehicles built on the TNGA platform—including the 12th Gen Corolla (E210 2019–2026), 5th Gen RAV4 (XA50 2019–2026), 8th Gen Camry (XV70 2018–2026), Highlander (XU70), Sienna, Venza, and Corolla Cross—the glovebox stays attached on its lower hinges, an internal shelf divider slides out, and the filter (#CF12157) sits inside a reusable white plastic carrier tray.
Tools: Hands only (no tools)
- Never throw away the white plastic filter carrier tray on a TNGA Toyota—only the pleated filter element (#CF12157 / OEM 87139-58010 or 87139-0E040) inside the carrier is replaced!
Exact TNGA Platform Fitment & Part Numbers
Compatible 2018–2026 Toyota & Lexus TNGA Models Using Filter #CF12157
The Toyota and Lexus models below take this 215 × 184.5 × 27 mm cabin air filter (FRAM’s size for #CF12157):
| Vehicle & Years | Chassis Series | TNGA Glovebox & Carrier Details | Exact Filter Part # (FRAM / OEM) | Arrow Rule |
|---|---|---|---|---|
| Toyota Corolla & Corolla Hatchback (2019–2026; 2019: check the old filter) | 12th Gen E210 (Gas & Hybrid) | Fixed lower hinges + right damper + left-hook/right-clip door + white carrier tray | FRAM #CF12157 · OEM 87139-58010 / 87139-0E040 / 87139-0R030 (was 87139-28020) | ↑ UP points UP (blower airflow is downward) |
| Toyota Corolla Cross (2022–2026) | XG10 | Fixed lower hinges + right damper + white filter carrier tray | FRAM #CF12157 · OEM 87139-0E040 / 87139-0R030 (was 87139-28020) | ↑ UP points UP |
| Toyota Prius (2016–2026) | XW50 / XW60 | Fixed lower hinges + right damper + white filter carrier tray | FRAM #CF12157 · OEM 87139-0R030 (was 87139-28020) / 87139-58010 (to 2022) | ↑ UP points UP |
| Toyota RAV4 (2019–2026) & RAV4 Prime (2021–2024) | 5th Gen XA50 (Gas, Hybrid & Prime) | Fixed lower hinges + removable sub-tray shelf divider + white carrier tray | FRAM #CF12157 · OEM 87139-58010 / 87139-0R030 (was 87139-28020) | ↑ UP points UP |
| Toyota Camry (2018–2026) | 8th Gen XV70 & 9th Gen XV80 | Fixed lower hinges + removable sub-tray shelf divider + white carrier tray | FRAM #CF12157 · OEM 87139-0E040 / 87139-58010 (2018–2019) | ↑ UP points UP |
| Toyota Highlander (2020–2026), Sienna (2021–2026) & Venza (2021–2024) | XU70, XL40 & XU80 | Fixed lower hinges + internal shelf divider + white carrier tray | FRAM #CF12157 · OEM 87139-58010 | ↑ UP points UP |
| Lexus ES, RX & UX (2019–2026) & NX (2022–2026) | XZ10, AL20/AL30, ZA10 & AZ20 | Right damper + internal velvet shelf divider + white carrier tray | FRAM #CF12157 · OEM 87139-0E040 (ES, RX, NX) / 87139-58010 (NX, UX) | ↑ UP points UP |
No matching series found. Clear the filter to view all compatible models.
Keep the Factory White Plastic Carrier Tray: On 2019–2026 Toyota TNGA models, OEM filters are frameless pleated elements that tuck under the four corner tabs of the reusable white plastic carrier tray. Some aftermarket filters (FRAM #CF12157) include a rigid perimeter frame—always retain the factory white carrier tray with the vehicle.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
X-ray view of the 2019–2026 Toyota TNGA passenger dash: the right-side damper arm, the two inner stopper claws, the removable sub-tray shelf divider, the right-clip/left-hook cover, and the white filter carrier tray.
Where not to force or pry
- No pry Passenger airbag in upper dash pad
- Unhook first Right damper arm: unclip before squeezing stoppers
- No debris Blower wheel under carrier tray
- Hook tab Left end is a slotted hook tab—pinch right clip only
Stoppers, right clip & carrier mark
- ↑ UP carrier mark
- Damper pin
- Right cover clip
- Stopper claw ×2
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed car.
All 6 steps
- 1Open passenger door and empty the glovebox
Turn the vehicle power off (READY light off on Hybrid models). Open the front passenger door wide, open the glovebox, and remove the owner’s manual and any items resting on both the lower floor and the internal horizontal shelf divider.
- 2Unhook the right-side hydraulic damper arm trap
On the right outer side of the glovebox (nearest the passenger door), push the lower loop of the black damper arm outward toward the door to unclip it from its plastic pin on the glovebox wall, and let the damper arm hang. Avoid this trap: If you squeeze the side walls past the stoppers while the right-side damper arm is still clipped onto its pin, the damper bottoms out and the weight of the glovebox snaps the plastic pin off the bin wall. Unclip the damper arm first.
- 3Squeeze side walls, lower glovebox & unclip sub-tray divider
Press both side walls of the glovebox inward to clear the dashboard stopper ledges and let the glovebox swing down on its fixed lower hinges. On TNGA models equipped with the horizontal plastic sub-tray shelf divider inside the glovebox, unclip and slide the divider shelf straight out so you have full access to the filter door behind it.
- 4Release the right cover clip and unhook the left tab
Locate the black rectangular filter access cover stamped ↑ UP. Pinch the single squeeze clip on the right end inward, pull the right side out toward you, and slide the left hook tab out of its slot in the white HVAC housing.
- 5Slide out the white filter carrier tray and remove the old filter
Pull the white plastic filter carrier tray straight out of the HVAC housing, keeping it level so leaves and dust on the upper face do not fall into the blower fan below. Note the ↑ UP arrow on the front of the white carrier tray, then remove the old pleated filter element from the carrier.
- 6Seat the new #CF12157 filter with ↑ UP pointing up and slide in trap
Place the new #CF12157 (OEM 87139-58010 or 87139-0E040) filter into the carrier / slot with its ↑ UP mark pointing straight up (and its end pleats tucked under the carrier’s corner tabs), then slide the tray smoothly into the housing until flush. Avoid this trap: Sliding the TNGA filter or carrier tray in with its ↑ UP arrow pointing down prevents the upper perimeter lip from sealing in the housing tracks and forces outside air through the filter media backwards.
What you need
- Cabin air filter #CF12157 / OEM 87139-58010 or 87139-0E040 · 215 × 184.5 × 27 mm (fits 2019–2026 TNGA models)
- Hands only (no tools) · glovebox stays hinged; shelf divider & carrier slide out
- Flashlight · optional, to check the corner tabs on the white carrier tray
Questions
Does a 2019–2026 Toyota Corolla or RAV4 take CF10285 or CF12157?
2019–2026 Toyota Corolla (E210), 2019–2026 RAV4 (XA50), and 2018–2026 Camry (XV70) models take #CF12157 (OEM 87139-58010 or 87139-0E040), which is 215 × 184.5 × 27 mm. The 2009–2018 Corolla and 2006–2018 RAV4 took #CF10285 (215 × 194 × 29 mm), a different size: about 9.5 mm deeper and 2 mm thicker. 2019 is the changeover year for the Corolla: FRAM lists both filters for 1.8L cars and only #CF12157 for the 2.0L, so check the filter that comes out.
Do I reuse the white plastic frame around the filter on a 2019–2026 RAV4, Camry, or Corolla?
Yes! The white plastic frame is a permanent Toyota carrier tray. Pull the carrier tray out, unclip the old filter media from the four corner tabs, tuck the new filter into the tray with ↑ UP pointing up, and slide the tray back in.
Which way does the arrow go on a 2019–2026 Toyota RAV4, Camry, or Corolla cabin filter?
Point the ↑ UP mark on the white carrier tray and OEM/FRAM filter straight UP. Actual airflow from the blower fan moves DOWNWARD (top to bottom), so if you use an aftermarket filter that prints AIR FLOW instead of UP, point the AIR FLOW arrow DOWN.
Safety
Switch the vehicle power off before reaching behind the glovebox. Set the climate control to Fresh Air mode before powering off so the recirculation door is not covering the upper housing.
- Engine off: switch the engine and the fan off and take the key away before you reach behind the dashboard or under the bonnet.
About this guide
3D Spatial Reconstruction: models are engineered from factual measurements to show the parts, the fixings and the order of the job before you start. Always check the handbook of your own car.
This 3D guide models the 2018–2026 Toyota TNGA cabin air filter architecture shared across the 12th Gen Corolla (E210), 5th Gen RAV4 (XA50), 8th/9th Gen Camry (XV70/XV80), Highlander (XU70), Sienna (XL40), Venza, and Corolla Cross.
Unlike older Toyotas that took filter #CF10285 (215 × 194 × 29 mm) and had a detachable glovebox, TNGA vehicles keep the glovebox attached on its lower hinges, include a removable horizontal sub-tray shelf divider inside the glovebox, and use a smaller filter (#CF12157, 215 × 184.5 × 27 mm: about 9.5 mm shallower and 2 mm thinner) seated inside a reusable white plastic carrier tray.
Part numbers and sizes checked on 10 November 2026: FRAM’s published size for #CF12157 works out at 215 × 184.5 × 27 mm, and FRAM lists it for the Camry from 2018, the Corolla and RAV4 from 2019, the Prius from 2016 and the other models in the table. Two Toyota parts catalogs (ToyotaPartsDeal and ToyotaPartsNow) list 87139-58010 for the Corolla, RAV4, Highlander, Sienna and Venza, 87139-0E040 for the Camry, Corolla and Corolla Cross, and 87139-0R030, which replaces 87139-28020, for the Corolla, RAV4, Prius and Corolla Cross; ToyotaPartsDeal replaces 87139-YZZ37 with 87139-YZZ93. For a 2019 Corolla FRAM lists both #CF12157 and the older #CF10285 (1.8L cars), so check the filter that comes out.
Sources: Toyota RAV4 (XA50) & Corolla (E210) Owner’s Manual: Air Conditioning Filter Maintenance (sub-tray divider, damper arm, carrier tray ↑ UP mark), FRAM: CF12157 Fresh Breeze cabin air filter, its Applications and Interchange tabs (8.464 × 7.263 × 1.062 in; fits the 2018–2027 Camry, 2019–2027 Corolla and RAV4, 2021–2024 RAV4 Prime, 2022–2027 Corolla Cross, 2016–2027 Prius, 2020–2026 Highlander, 2021–2026 Sienna, 2021–2024 Venza and the Lexus ES 2019–2026, RX 2016–2026, UX 2019–2026 and NX 2022–2026; interchanges with Toyota 87139-58010, 87139-0E040, 87139-28020 and 87139-YZZ37; read 10 November 2026), FRAM: CF10285 Fresh Breeze cabin air filter, its Applications tab (8.471 × 7.644 × 1.143 in; the 2009–2019 Corolla, 2006–2018 RAV4 and 2007–2017 Camry; for a 2019 Corolla 1.8L FRAM lists both filters, for the 2.0L only CF12157; read 10 November 2026), ToyotaPartsDeal: genuine Toyota cabin air filters for the Corolla (87139-58010 and 87139-28020 for 2019–2024, 87139-0E040 for 2020–2024; its RAV4 page lists 87139-58010 and 87139-0R030, which replaces 87139-28020, for 2019–2024, its Camry page 87139-0E040 for 2018–2024 and 87139-58010 for 2018–2019, its Highlander, Sienna and Venza pages 87139-58010, its Corolla Cross page 87139-0E040 and 87139-0R030, its Prius page 87139-58010 for 2016–2022 and 87139-28020 for 2016–2024; read 10 November 2026), ToyotaPartsNow: genuine Toyota cabin air filters for the Corolla (87139-58010 and 87139-0R030, which replaces 87139-28020, for 2019–2025, 87139-0E040 for 2021–2025; its RAV4 page lists 87139-58010 and 87139-0R030 for 2019–2025, its Camry page 87139-0E040 for 2018–2025 and 87139-58010 for 2018–2019, its Highlander, Sienna and Venza pages 87139-58010, its Corolla Cross page 87139-0R030 and 87139-0E040, its Prius page 87139-58010 for 2016–2022 and 87139-0R030 for 2016–2025; read 10 November 2026), ToyotaPartsDeal: genuine Toyota 87139-YZZ93 (it replaces 87139-YZZ37; read 10 November 2026), LexusPartsNow: genuine Lexus cabin air filters for the ES 350 (87139-0E040 for 2019–2024; its RX 350 page lists 87139-0E040 for 2016–2025, its NX 350 page 87139-0E040 for 2022–2025 and 87139-58010 for 2022–2023, its UX 250h page 87139-58010 for 2019–2024; read 10 November 2026), Price: Filterbuy cost guide, cabin air filter replacement at a quick-lube or tyre chain, $40–$100 (updated July 2026, read 9 November 2026).
The 3D models, drawings and text are our own. The 3D cabin is an unbadged reconstruction of this vehicle’s own layout, from its maker’s procedure and the sources above, not the maker’s own model or a scan. Toyota, Lexus, Corolla, RAV4, Camry, Highlander, Sienna, Venza, Prius and FRAM are trademarks of their respective owners, named strictly in text to indicate mechanical compatibility and fastener/part specifications (nominative fair use); iTakeApart is not affiliated with or endorsed by any vehicle manufacturer.