Fix it yourself, pay a repair shop, or replace it?
FaultClogged cabin air filter
Garage
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
6 steps · No tools · 2016–2026 Honda Civic / CR-V / Accord · Part #CF11182
2016–2026 Honda Civic, CR-V & Accord Cabin Air Filter Replacement: interactive 3D repair guide
Honda standardized almost its entire 2016–2026 lineup—including the 10th & 11th Gen Civic (FC/FK/FE/FL), 5th & 6th Gen CR-V (RW/RS), 10th & 11th Gen Accord (CV/CY), HR-V, Fit, Odyssey, and Acura Integra—around a single tool-free behind-the-glovebox architecture using filter #CF11182 (OEM 80291-TF3-E01, formerly 80292-TBA-A11) with ↓ AIR FLOW pointing down. The 2018–2022 Accord takes Honda’s larger 80292-SDA-407 filter.
What you need
On the 2016–2026 Honda Civic (10th Gen FC/FK & 11th Gen FE/FL), 2017–2026 CR-V (5th Gen RW & 6th Gen RS), 2018–2026 Accord (CV/CY), HR-V, Odyssey, and Acura Integra/RDX, the cabin air filter (#CF11182 / OEM 80291-TF3-E01, formerly 80292-TBA-A11) sits behind the passenger glovebox; the 2018–2022 Accord’s is Honda’s larger 80292-SDA-407. Unlike Toyota’s UP mark, Honda prints ↓ AIR FLOW pointing straight DOWN toward the lower blower fan.
Tools: Hands only (no tools)
- Check your filter number: almost all modern 2016–2026 Honda models use FRAM #CF11182 or Honda OEM 80291-TF3-E01 (211 × 205 × 28.5 mm). Honda’s 80291-TF3-E01 replaced 80292-TBA-A11 and 80291-T5R-A01, so an older box may carry either of those numbers. The 2018–2022 Accord is the exception: it takes Honda’s larger 80292-SDA-407.
Exact Honda / Acura Fitment & Part Numbers
Compatible Honda & Acura Models Using Filter #CF11182 (80291-TF3-E01, formerly 80292-TBA-A11)
Every Honda and Acura series below uses the 2-clip filter housing and ↓ AIR FLOW downward arrow orientation, and all but the 2018–2022 Accord take this 211 × 205 × 28.5 mm filter:
| Vehicle & Years | Generation & Chassis Code | Glovebox & Cover Mechanics | Exact Filter Part # (FRAM / OEM) | Arrow Direction |
|---|---|---|---|---|
| Honda Civic Sedan, Coupe, Hatchback, Si & Type R (2016–2026) | 10th Gen FC/FK (2016–2021) & 11th Gen FE/FL (2022–2026) | Right damper catch + squeeze-in side stops + 2-clip pinch cover | FRAM #CF11182 · OEM 80291-TF3-E01 (replaces 80292-TBA-A11 / 80291-T5R-A01) | ↓ AIR FLOW points DOWN toward the blower fan |
| Honda Accord (2018–2022) | 10th Gen CV | Right damper catch + squeeze-in side stops + 2-clip pinch cover | OEM 80292-SDA-407 (a larger filter, also fitted to the Pilot) | ↓ AIR FLOW points DOWN |
| Honda Accord & Accord Hybrid (2023–2026) | 11th Gen CY | Right damper catch + squeeze-in side stops + 2-clip pinch cover | FRAM #CF11182 · OEM 80291-TF3-E01 (replaces 80292-TBA-A11) | ↓ AIR FLOW points DOWN |
| Acura Integra (2023–2026) & TLX (2021–2025) | DE4/DE5 & UB5/UB6 | Right damper catch + squeeze-in side stops + 2-clip pinch cover | FRAM #CF11182 · OEM 80291-TF3-E01 (replaces 80292-TBA-A11) | ↓ AIR FLOW points DOWN |
| Honda CR-V & CR-V Hybrid (2017–2026) | 5th Gen RW (2017–2022) & 6th Gen RS (2023–2026) | Right damper catch + squeeze-in side stops + 2-clip pinch cover | FRAM #CF11182 · OEM 80291-TF3-E01 (replaces 80292-TBA-A11) | ↓ AIR FLOW points DOWN |
| Honda HR-V (2016–2026), Fit (2015–2020) & Odyssey (2018–2026) | RU / RZ, GK & RL6 | Right damper catch + squeeze-in side stops + 2-clip pinch cover | FRAM #CF11182 · OEM 80291-TF3-E01 (replaces 80292-TBA-A11) | ↓ AIR FLOW points DOWN |
| Acura RDX (2019–2026) & MDX (2022–2026) | TC1/TC2 & YD8/YD9 | Right damper catch + squeeze-in side stops + 2-clip pinch cover | FRAM #CF11182 · OEM 80291-TF3-E01 (RDX; replaces 80292-TBA-A11) / 80292-TYB-A51 (MDX) | ↓ AIR FLOW points DOWN |
No matching series found. Clear the filter to view all compatible models.
Honda ↓ AIR FLOW Rule: Unlike Toyota (which prints ↑ UP), Honda molds ↓ AIR FLOW with a downward-pointing arrow directly onto the plastic filter cover and prints ↓ AIR FLOW on the filter edge. Always point the AIR FLOW arrow DOWN (↓) toward the blower fan.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
X-ray view of the 2016–2026 Honda Civic / CR-V passenger dash: the right-side damper arm, the two inner glovebox stops, the rectangular cover with clips at BOTH ends, and the ↓ AIR FLOW downward mark.
Where not to force or drop debris
- No pry Passenger airbag module in upper dash
- Unhook first Right damper arm: push downward/outward off catch first
- No debris Blower wheel below filter: keep leaves out
- Hidden cable Blower motor power harness
Side stops, dual cover clips & ↓ AIR FLOW mark
- ↓ AIR FLOW mark
- Damper catch
- Left cover clip
- Left/right stop tab ×2
- Right cover clip
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed car.
All 6 steps
- 1Turn ignition off, open passenger door & empty glovebox
Switch the ignition and climate control fan off. Open the front passenger door wide, pull the glovebox latch, and move the owner’s manual and contents onto the passenger seat—the Honda glovebox swings straight down on its lower hinge in Step 3, so anything left inside will spill onto the floor.
- 2Push the right-side damper arm downward/outward to unhook it trap
Look on the right outer wall of the glovebox (by the passenger door) to find the telescopic damper arm. Support the glovebox lid with one hand and push the damper arm’s lower end downward and outward to unhook it from its slotted plastic catch on the side of the glovebox. Avoid this trap: If you squeeze the side stops and let the glovebox drop straight down on its hinge while the right-side damper arm is still hooked, the glovebox’s weight yanks the damper past the end of its stroke and breaks the plastic catch. Always unhook the damper arm first.
- 3Squeeze both inner side stops and let the glovebox hang down
Place your hands on the left and right outer walls of the glovebox and squeeze both side walls inward toward the middle so the two stopper tabs clear the dashboard frame. Slowly lower the glovebox until it hangs straight down on its fixed bottom hinge, exposing the HVAC housing behind it.
- 4Pinch BOTH left and right cover clips and pull straight out
Unlike Toyota covers that hook on the left and clip on the right, the Honda Civic & CR-V filter cover has a sprung pinch tab at BOTH ends. Pinch the left and right clips inward toward the center simultaneously and pull the cover straight out toward you.
- 5Slide the old #CF11182 filter straight out level
Grip the front edge of the old #CF11182 filter and slide it straight out toward you, keeping it level so leaves, acorns, and dust trapped in the top pleats do not fall into the squirrel-cage blower fan right below the slot.
- 6Point the ↓ AIR FLOW arrow DOWN and slide the new #CF11182 filter in trap
Locate the AIR FLOW arrow printed on the front edge of your new #CF11182 (OEM 80291-TF3-E01, formerly 80292-TBA-A11) cabin filter. Turn the filter so the ↓ AIR FLOW arrows point straight DOWN toward the floor (matching the blower fan suction below) and slide it in level until flush. Avoid this trap: Because the Honda blower fan sits underneath the filter and pulls outside air downward, installing the #CF11182 filter with its AIR FLOW arrow pointing up puts the progressive filter media and activated carbon layer upside down—causing it to clog faster and restricting vent output.
What you need
- Cabin air filter #CF11182 / OEM 80291-TF3-E01 (was 80292-TBA-A11) · 211 × 205 × 28.5 mm (fits 2016–2026 Civic, CR-V & HR-V, 2023–2026 Accord)
- Hands only (no tools) · 2-clip cover & squeeze-in glovebox stops
- Flashlight · optional, to check the blower wheel under the slot
Questions
Which way does the AIR FLOW arrow point on a Honda Civic or CR-V cabin air filter?
Point the ↓ AIR FLOW arrow straight DOWN toward the floor. Outside air enters from the base of the windshield above the filter and is pulled downward by the blower fan located directly underneath the filter slot.
What cabin air filter part number fits a 2016–2026 Honda Civic, CR-V, or Accord?
All 2016–2026 Honda Civic, 2017–2026 CR-V, and 2023–2026 Accord models take FRAM #CF11182, Honda OEM 80291-TF3-E01, Purolator C36080 or Wix 24201 (211 × 205 × 28.5 mm). Honda’s 80291-TF3-E01 replaced 80292-TBA-A11 and 80291-T5R-A01, so an older box may still show either of those numbers. The 2018–2022 Accord takes Honda’s larger 80292-SDA-407 instead.
What does Honda Maintenance Minder code Sub-Item 2 mean?
On Honda vehicles, Maintenance Minder Sub-Item 2 indicates that the engine dust and pollen filter (cabin air filter) is due for replacement—typically every 15,000 miles or once a year.
Safety
Turn the ignition and climate control blower fan completely off before opening the filter housing. Slide the old filter out level so leaves and acorns on top of the pleats do not drop into the blower squirrel cage.
- Engine off: switch the engine and the fan off and take the key away before you reach behind the dashboard or under the bonnet.
About this guide
3D Spatial Reconstruction: models are engineered from factual measurements to show the parts, the fixings and the order of the job before you start. Always check the handbook of your own car.
This 3D guide models the behind-the-glovebox cabin air filter replacement on 2016–2026 Honda and Acura vehicles using filter #CF11182 (OEM 80291-TF3-E01, formerly 80292-TBA-A11), including the 10th & 11th Gen Civic (FC/FK/FE/FL), 5th & 6th Gen CR-V (RW/RS), 11th Gen Accord (CY), HR-V, Fit, Odyssey, and Acura Integra/RDX.
Unlike Toyota covers (which hook on the left and clip on the right), Honda’s rectangular filter door uses sprung pinch clips at both the left and right ends, and both the housing cover and the filter edge are marked ↓ AIR FLOW pointing straight down toward the blower wheel.
Honda’s genuine filter for these cars is now 80291-TF3-E01, which replaces 80292-TBA-A11 and 80291-T5R-A01 (Bernardi Parts and HondaPartsNow, two Honda parts dealers), so an older filter or box may carry either of those numbers. Both dealers list it for the 2023 and later Accord only: the 2018–2022 Accord takes Honda’s 80292-SDA-407, a larger filter also fitted to the Pilot, and Bernardi lists no cabin filter for the 2018–2022 Accord Hybrid. Bernardi’s list for 80291-TF3-E01 also names the 2016–2026 Civic, 2017–2026 CR-V, 2016–2026 HR-V and 2018–2026 Odyssey. Bernardi’s Acura site lists it for the 2023–2026 Integra, 2019–2026 RDX and 2021–2025 TLX, and 80292-TYB-A51 for the 2022–2026 MDX; for the 2015–2020 Fit, check the number on your old filter.
Sources: Bernardi Parts Honda: How to Change a Honda Cabin Air Filter (unhook damper arm, squeeze side stops, pinch both cover tabs, point AIR FLOW arrows down, Maintenance Minder B1/Sub-item 2), FRAM: CF11182 Fresh Breeze cabin air filter, its Applications and Interchange tabs (8.313 × 8.057 × 1.123 in; fits the 2016–2026 Civic, 2017–2026 CR-V, 2023–2026 Accord, 2016–2027 HR-V, 2009–2020 Fit, 2018–2027 Odyssey and the Acura RDX 2019–2026, TLX 2021–2025, MDX 2022–2027 and Integra 2023–2027; interchanges with Purolator C36080, Wix 24201 and Honda 80291-TF3-E01, 80292-TBA-A11 and 80291-T5R-A01, but names no Bosch filter; read 10 November 2026), Price: Filterbuy cost guide, cabin air filter replacement at a quick-lube or tyre chain, $40–$100 (updated July 2026, read 9 November 2026), Bernardi Parts Honda: Honda cabin filter 80292-SDA-407 (fits the 2010–2022 Accord, the 2009–2022 Pilot and others; the cabin filter on its 2018–2022 Accord Sedan maintenance page, whose 2023–2026 page lists 80291-TF3-E01 and whose 2018–2022 Accord Hybrid page lists none; read 9 November 2026), HondaPartsNow: genuine Honda 80291-TF3-E01 (it replaces 80292-TBA-A11 and 80291-T5R-A01; fits the 2016–2026 Civic, 2017–2026 CR-V, 2018–2026 Odyssey and 2023–2025 Accord; listed at 8.3 × 8.2 × 1.3 in; read 9 November 2026), HondaPartsNow: genuine Honda 80292-SDA-407 (fits the 2013–2022 Accord among others, and the 2009–2022 Pilot; listed at 9.5 × 9.7 × 1.3 in; read 9 November 2026), Bernardi Parts Acura: Acura cabin pollen filter 80291-TF3-E01 (fits the 2025–2026 ADX, 2023–2026 Integra, 2019–2026 RDX and 2021–2025 TLX; the cabin filter on those models’ maintenance pages; read 10 November 2026), Bernardi Parts Acura: Acura cabin pollen filter 80292-TYB-A51 (fits the 2022–2026 MDX; the cabin filter on its maintenance page; read 10 November 2026), Price: Bernardi Parts Honda, genuine Honda cabin pollen filter 80291-TF3-E01, $29.25 (it replaces 80292-TBA-A11 and 80291-T5R-A01, and fits the 2016–2026 Civic, 2017–2026 CR-V, 2023–2026 Accord, 2016–2026 HR-V and 2018–2026 Odyssey; read 9 November 2026).
The 3D models, drawings and text are our own. The 3D cabin is an unbadged reconstruction of this vehicle’s own layout, from its maker’s procedure and the sources above, not the maker’s own model or a scan. Honda, Acura, Civic, CR-V, Accord, HR-V, Odyssey, Integra, RDX, FRAM, Purolator and Wix are trademarks of their respective owners, named strictly in text to indicate mechanical compatibility and fastener/part specifications (nominative fair use); iTakeApart is not affiliated with or endorsed by any vehicle manufacturer.