Fix it yourself, pay a repair shop, or replace it?
- PartNo sourced figure
- Toolsnot priced
- Time30–45 min
- 3D risk levelMedium
How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →
Measurements in
5 steps · 2 traps to avoid · Snap-on earpad ring, 40mm/30mm driver baffle, 3.7 V battery & swivel hinge
Sony WH-1000XM4 & XM5 Hinge & Battery: interactive 3D teardown
Whether your Sony WH-1000XM4 or WH-1000XM5 has a snapped swivel hinge yoke or a 3.7 V pouch battery that drains in an hour, every repair starts inside the earcup: unclip the 6-tab snap-on earpad mounting ring, lift the acoustic foam baffle, remove the 4 × 1.7 × 5.0 mm #00 Phillips driver plate screws, and hinge the baffle plate open gently before touching the ZIF ribbon or swivel pivot harness.
What you need
The right earcup of a Sony WH-1000XM4 / WH-1000XM5 wireless noise-cancelling headphone on an anti-static mat, earpad side up: under the snap-on earpad mounting ring and acoustic foam baffle sits the angled 40 mm / 30 mm driver plate, the NFC & capacitive touch sensor panel, the 3.7 V lithium-ion pouch battery, and the swivel hinge yoke assembly with the cross-headband wire harness threading through the pivot joint.
Tools: Plastic pry tool / nylon spudger, Phillips #00 screwdriver
- Power the headphones off completely and unplug any USB-C charging cable before unclipping the earpad ring.
Fits / Compatible Sony 1000X Wireless ANC Headphone Series
Sony WH-1000XM4 vs. WH-1000XM5 Battery, Driver Baffle & Swivel Hinge Reference
Both the Sony WH-1000XM4 and WH-1000XM5 hide their 4 × #00 Phillips driver baffle screws beneath a 6-clip snap-on earpad mounting ring and acoustic foam damper, house the 3-wire 3.7 V / 3.8 V lithium-ion pouch battery in the right earcup, and route the cross-headband wire harness directly through the hollow swivel hinge pivot joint:
| Headphone Model | Driver & Earpad Ring | Battery Part # & Specs (Right Cup) | Swivel Hinge Mechanism | Key Internal Trap |
|---|---|---|---|---|
Sony WH-1000XM4 (YY2948) | 40 mm LCP dome driver · 6-clip oval snap-on earpad ring + 4 × 1.7 × 5.0 mm #00 Phillips baffle screws | LIS1662HNPC (3.7 V · 1050 mAh / 3.9 Wh · 3-pin JST with white NTC thermistor wire) | Folding hanger fork + metal/plastic swivel pivot C-clip (A-5019-976-A / A-5019-977-A) held by 2 internal screws | Yanking the driver baffle pulls the ANC mic & proximity sensor flex; clamping the swivel C-clip pinches the headband harness |
Sony WH-1000XM5 (YY2954) | 30 mm carbon-fiber dome driver · 6-clip low-profile earpad ring + 4 × #00 Phillips baffle screws | SP624038 / A-5046-320-A (3.8 V · 1100 mAh / 4.18 Wh · 3-pin JST with NTC thermistor) | Cylindrical stepless slider stem with internal metal knurled swivel ring & 2-screw pivot retainer inside cup top | Pulling the baffle plate before releasing the ZIF ribbon tears the multi-mic ANC array flex; pinching the 16-wire stem harness |
Sony WH-1000XM3 (WH1000XM3) | 40 mm LCP dome driver · 6-clip snap-on earpad ring + 4 × 1.7 × 5.0 mm #00 Phillips baffle screws | LIS1662HNPC (3.7 V · 1050 mAh / 3.9 Wh · 3-pin JST) | Folding hanger fork with internal swivel stopper clip & 2 Phillips #00 retainer screws | Forgetting to transfer the small plastic swivel rotation-limiter U-clip to the replacement hanger yoke |
No matching series found. Clear the filter to view all compatible models.
Right vs. Left Earcup Layout: On both the WH-1000XM4 and WH-1000XM5, the 3.7 V / 3.8 V pouch battery and capacitive touch sensor panel sit inside the Right (R) earcup, while the main USB-C / power-button / ANC board sits in the Left (L) earcup. A broken swivel hinge on either side uses the exact same earpad → foam → 4-screw baffle → 2-screw internal pivot retainer sequence.
Unbadged 3D Geometry & Nominative Fair Use: All 3D vehicle, engine, and key fob meshes are 100% unbadged original reconstructions. Manufacturer names, model series, chassis codes, and industry part numbers are referenced strictly in text to identify mechanical compatibility and fastener/consumable specifications. Always verify against your vehicle’s owner’s manual.
Before you open it: the risk map
Seen through the closed earcup: the 4 × 5.0 mm #00 Phillips driver baffle screws under the acoustic foam, the short ANC & touch-panel ZIF ribbon cable, the 3.7 V lithium-ion pouch battery in the right cup, and the 2 × 5.0 mm swivel hinge retainer screws astride the cross-headband wire harness.
Hidden ribbon, driver cone, battery & pivot wire zones
- Short ribbon · max 4 mm ANC mic & touch-panel ZIF ribbon: hinge baffle open gently
- No metal pry 3.7 V Li-ion pouch cell (LIS1662HNPC / SP624038): nylon spudger only
- Pinch hazard Cross-headband wire harness threading through swivel pivot joint
- Driver dome 40mm / 30mm driver diaphragm & magnet: keep steel tools clear
Screw length map (6 × Phillips #00)
- Phillips #00 · 5.0 mm (driver baffle) ×4
- Phillips #00 · 5.0 mm (swivel hinge retainer) ×2
Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed earcup.
All 5 steps
- 1Unclip the snap-on earpad ring & lift the acoustic foam
Slip the flat edge of a plastic pry tool between the earcup rim and the inner plastic mounting ring of the earpad cushion. Work around the oval perimeter to pop all 6 snap tabs with an audible click, set the earpad on the mat, and lift out the oval grey acoustic foam baffle covering the driver plate.
- 2Unscrew the 4 driver baffle screws & hinge the plate open trap
Use a #00 Phillips screwdriver to remove the 4 black 1.7 × 5.0 mm screws securing the driver baffle plate to the earcup boss posts. Lift the baffle plate only 15 mm along one edge and hinge it open slowly like a book—do not pull it straight out yet, because the delicate ANC feedback microphone wire and touch-sensor ribbon cable are still anchored underneath. Avoid this trap: Once the 4 perimeter screws are out, the driver baffle feels loose, tempting you to lift it straight off the earcup. Doing so pulls the short internal ribbon cable and ANC feedback microphone harness taut and rips the flex traces before you can reach the ZIF latch, killing active noise cancellation and touch gestures.
- 3Flip the ZIF ribbon latch & unplug the 3.7 V battery
With the driver plate tilted open, use the tip of a nylon spudger to flip up the black hinged locking flap on the ZIF ribbon connector and slide the flex cable free so the baffle plate can rest safely beside the earcup. Then walk the white 3-pin JST battery plug (red +, white NTC thermistor, black −) straight out of its board socket.
- 4Release and lift out the 3.7 V lithium-ion pouch battery
Slide the flat blade of the nylon spudger slowly beneath the edge of the 3.7 V lithium-ion pouch battery (Sony LIS1662HNPC in the WH-1000XM4, or SP624038 in the WH-1000XM5) to ease it off its double-sided adhesive pad above the NFC and capacitive touch-sensor panel. Lift the old pouch cell out and place it in the tray.
- 5Unscrew the swivel hinge retainer & thread the wire harness trap
Unscrew the 2 × 1.7 × 5.0 mm Phillips #00 screws holding the internal swivel hinge retainer clip at the top of the earcup, lift off the retainer clip, and carefully thread the multi-strand cross-headband wire harness through the slot of the pivot joint to free the broken swivel hinge yoke. Avoid this trap: The multi-conductor wire harness connecting the left and right earcups passes directly through the hollow center of the swivel hinge post. If the wire bundle slips out of its recessed guide groove while you screw down the internal hinge retainer clip, the plastic rib pinches through the thin insulation—cutting off audio, ANC microphones, or power between the earcups.
What you need
- Plastic pry tool / nylon spudger · to unclip the 6 earpad tabs, flip the ZIF latch, and release battery adhesive
- Phillips #00 precision screwdriver · for the 4 driver baffle screws and 2 internal swivel hinge retainer screws
- Replacement 3.7 V pouch battery or swivel hinge kit · LIS1662HNPC (XM4) / SP624038 (XM5) 3-wire cell, or left/right swivel yoke
Questions
How do the Sony WH-1000XM4 and WH-1000XM5 earpads come off?
Both use a rigid plastic mounting ring bonded to the base of the earpad cushion with 6 perimeter snap tabs. Slip a flat plastic pry tool under the inner rim of the earpad and work around the oval perimeter until all 6 clips pop free—do not pull on the soft leatherette foam alone.
Which earcup holds the battery on the Sony WH-1000XM4 and WH-1000XM5?
The 3.7 V / 3.8 V lithium-ion pouch battery sits inside the Right (R) earcup alongside the NFC coil and capacitive touch-sensor panel. The Left (L) earcup holds the main USB-C charging port, power/NC buttons, and primary audio board.
Why does my Sony WH-1000XM4 or XM5 blink red and refuse to charge after a battery swap?
Sony’s charging circuit monitors the middle white wire on the 3-pin JST battery plug, which connects to an internal 10 kΩ NTC thermistor inside the battery pack. If the plug is not seated squarely or a cheap 2-wire cell without a working thermistor is used, the headphone aborts charging.
Can you replace a broken Sony WH-1000XM4 or XM5 swivel hinge without soldering?
You can replace the outer folding hanger fork or re-seat a popped swivel C-clip without soldering by unclipping the internal pivot retainer and threading the slack of the wire harness through the slot in the yoke. If the full closed-loop swivel housing is replaced from scratch, check whether your replacement kit uses a split-slot yoke or requires unpinning the micro-connector on the board.
Safety
Switch the headphones off and unplug any USB-C cable before opening the earcup. Unplug the 3-wire battery JST connector before working near the circuit board or hinge screws, and never pry the foil lithium-ion pouch battery with a metal screwdriver.
- Lithium-ion batteries: never bend, puncture or pry a battery with metal. A damaged cell can go into thermal runaway: it smokes, catches fire and can explode. Discharge it below 25% first; if it swells, hisses, smokes or gets hot, stop and move it somewhere safe.
- Static (ESD): work on an anti-static mat with a grounded wrist strap; a spark you cannot feel can kill a chip.
- Power off: switch the device off and unplug its charger before you open it, and disconnect the battery before touching anything else inside.
About this teardown
3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.
This 3D teardown models the right earcup architecture shared across Sony’s flagship WH-1000XM4 and WH-1000XM5 wireless noise-cancelling headphones: an oval snap-on earpad mounting ring with 6 perimeter clips, a removable open-cell acoustic foam damper, an angled driver baffle plate held by 4 × 1.7 × 5.0 mm #00 Phillips screws, an internal ZIF ribbon cable linking the inner ANC feedback microphone and capacitive touch sensor panel, a 3.7 V / 3.8 V 3-wire lithium-ion pouch battery (Sony LIS1662HNPC / SP624038), and the top swivel hinge yoke assembly with the cross-headband wire harness threading through the hollow pivot post.
The two classic DIY failures are modeled directly as interactive 3D traps: pulling the unscrewed driver baffle plate straight off before flipping the ZIF ribbon latch, and clamping the replacement swivel hinge retainer clip down over a stray loop of the cross-headband wire bundle.
Sources: iFixit: Sony WH-1000XM4 Battery Replacement & Earpad Disassembly (6-clip snap-on earpad ring, foam insert, 4 × 5.0 mm Phillips #00 baffle screws, LIS1662HNPC 3.7 V 1050 mAh 3.9 Wh pouch battery), iFixit: Sony WH-1000XM4 Swivel Hinge & Hanger Replacement (routing the cross-headband wire harness through the pivot joint and securing the internal retainer clip), iFixit: Sony WH-1000XM5 Teardown & Repair Reference (30 mm driver baffle, 6-clip earpad ring, SP624038 3-wire battery, stepless slider swivel joint), Price: Target Certified Refurbished, Sony WH-1000XM4, $159.99, out of stock when read (new WH-1000XM5: $399.99; 9 November 2026), Price: Apolonia on Tindie, stainless steel WH-1000XM4 hinge, $15 for two, a third-party part (9 November 2026).
The 3D models, drawings and text are our own. Sony, WH-1000XM4 and WH-1000XM5 are trademarks of their owners, named only to say which device this teardown is for; iTakeApart is not affiliated with them.