Sony WH-1000XM4 & XM5 Hinge & BatterySony WH-1000XM4 / XM5WH-1000XM4 / XM5

Steps ↓
✓ Spec-Researched Risk: Med 30–45 min
Teardown · step by step WH-1000XM4 / XM5

✓ Spec-Researched 3D Guide

🟡 Overall risk: Medium ⏱ 30–45 min 💰 DIY $15
Step0/5
Screws out0/6
Connectors0/2
BatteryIn cup
Step riskLOW
What you need5 steps · press play

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this teardown.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby repair shops

Opens local search results in Google Maps for your device and a postcode or city. We do not check, rate or recommend the repair shops it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itDIY or a repair shop?
Overall repair riskMedium
Time required30–45 min
What can go wrongTearing the ANC microphone / touch-panel ribbon by pulling the driver baffle straight up, or pinching the cross-headband wire harness in the swivel hinge clip.
Cost comparison DIY: a third-party steel hinge pair, $15; battery variesGet the part ↗Get the kit ↗ Shop: varies by shopSearch nearby repair shops ↗Opens local search results in Google Maps US prices, checked November 2026; they vary by shop and country.
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

Fault
Your time is worth
Fix it yourselfNo sourced figure
  • PartNo sourced figure
  • Toolsnot priced
  • Time30–45 min
  • 3D risk levelMedium
Repair shopNo sourced figure
New or refurbished$159.99

Certified refurbished from Target: Sony WH-1000XM4

Consider a Repair ShopIt has a delicate ribbon-cable trap (step 2).Search nearby repair shops ↗Opens local search results in Google Maps

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

5 steps · 2 traps to avoid · Snap-on earpad ring, 40mm/30mm driver baffle, 3.7 V battery & swivel hinge

Sony WH-1000XM4 & XM5 Hinge & Battery: interactive 3D teardown

✓ Spec-Researched 3D Guide

Whether your Sony WH-1000XM4 or WH-1000XM5 has a snapped swivel hinge yoke or a 3.7 V pouch battery that drains in an hour, every repair starts inside the earcup: unclip the 6-tab snap-on earpad mounting ring, lift the acoustic foam baffle, remove the 4 × 1.7 × 5.0 mm #00 Phillips driver plate screws, and hinge the baffle plate open gently before touching the ZIF ribbon or swivel pivot harness.

What you need

The right earcup of a Sony WH-1000XM4 / WH-1000XM5 wireless noise-cancelling headphone on an anti-static mat, earpad side up: under the snap-on earpad mounting ring and acoustic foam baffle sits the angled 40 mm / 30 mm driver plate, the NFC & capacitive touch sensor panel, the 3.7 V lithium-ion pouch battery, and the swivel hinge yoke assembly with the cross-headband wire harness threading through the pivot joint.

Tools: Plastic pry tool / nylon spudger, Phillips #00 screwdriver

Fits / Compatible Sony 1000X Wireless ANC Headphone Series

Sony WH-1000XM4 vs. WH-1000XM5 Battery, Driver Baffle & Swivel Hinge Reference

Both the Sony WH-1000XM4 and WH-1000XM5 hide their 4 × #00 Phillips driver baffle screws beneath a 6-clip snap-on earpad mounting ring and acoustic foam damper, house the 3-wire 3.7 V / 3.8 V lithium-ion pouch battery in the right earcup, and route the cross-headband wire harness directly through the hollow swivel hinge pivot joint:

Headphone ModelDriver & Earpad RingBattery Part # & Specs (Right Cup)Swivel Hinge MechanismKey Internal Trap
Sony WH-1000XM4 (YY2948)40 mm LCP dome driver · 6-clip oval snap-on earpad ring + 4 × 1.7 × 5.0 mm #00 Phillips baffle screwsLIS1662HNPC (3.7 V · 1050 mAh / 3.9 Wh · 3-pin JST with white NTC thermistor wire)Folding hanger fork + metal/plastic swivel pivot C-clip (A-5019-976-A / A-5019-977-A) held by 2 internal screwsYanking the driver baffle pulls the ANC mic & proximity sensor flex; clamping the swivel C-clip pinches the headband harness
Sony WH-1000XM5 (YY2954)30 mm carbon-fiber dome driver · 6-clip low-profile earpad ring + 4 × #00 Phillips baffle screwsSP624038 / A-5046-320-A (3.8 V · 1100 mAh / 4.18 Wh · 3-pin JST with NTC thermistor)Cylindrical stepless slider stem with internal metal knurled swivel ring & 2-screw pivot retainer inside cup topPulling the baffle plate before releasing the ZIF ribbon tears the multi-mic ANC array flex; pinching the 16-wire stem harness
Sony WH-1000XM3 (WH1000XM3)40 mm LCP dome driver · 6-clip snap-on earpad ring + 4 × 1.7 × 5.0 mm #00 Phillips baffle screwsLIS1662HNPC (3.7 V · 1050 mAh / 3.9 Wh · 3-pin JST)Folding hanger fork with internal swivel stopper clip & 2 Phillips #00 retainer screwsForgetting to transfer the small plastic swivel rotation-limiter U-clip to the replacement hanger yoke

Right vs. Left Earcup Layout: On both the WH-1000XM4 and WH-1000XM5, the 3.7 V / 3.8 V pouch battery and capacitive touch sensor panel sit inside the Right (R) earcup, while the main USB-C / power-button / ANC board sits in the Left (L) earcup. A broken swivel hinge on either side uses the exact same earpad → foam → 4-screw baffle → 2-screw internal pivot retainer sequence.

Before you open it: the risk map

Seen through the closed earcup: the 4 × 5.0 mm #00 Phillips driver baffle screws under the acoustic foam, the short ANC & touch-panel ZIF ribbon cable, the 3.7 V lithium-ion pouch battery in the right cup, and the 2 × 5.0 mm swivel hinge retainer screws astride the cross-headband wire harness.

Hidden ribbon, driver cone, battery & pivot wire zones

Screw length map (6 × Phillips #00)

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed earcup.

All 5 steps

  1. 1Unclip the snap-on earpad ring & lift the acoustic foam

    Slip the flat edge of a plastic pry tool between the earcup rim and the inner plastic mounting ring of the earpad cushion. Work around the oval perimeter to pop all 6 snap tabs with an audible click, set the earpad on the mat, and lift out the oval grey acoustic foam baffle covering the driver plate.

  2. 2Unscrew the 4 driver baffle screws & hinge the plate open trap

    Use a #00 Phillips screwdriver to remove the 4 black 1.7 × 5.0 mm screws securing the driver baffle plate to the earcup boss posts. Lift the baffle plate only 15 mm along one edge and hinge it open slowly like a book—do not pull it straight out yet, because the delicate ANC feedback microphone wire and touch-sensor ribbon cable are still anchored underneath. Avoid this trap: Once the 4 perimeter screws are out, the driver baffle feels loose, tempting you to lift it straight off the earcup. Doing so pulls the short internal ribbon cable and ANC feedback microphone harness taut and rips the flex traces before you can reach the ZIF latch, killing active noise cancellation and touch gestures.

  3. 3Flip the ZIF ribbon latch & unplug the 3.7 V battery

    With the driver plate tilted open, use the tip of a nylon spudger to flip up the black hinged locking flap on the ZIF ribbon connector and slide the flex cable free so the baffle plate can rest safely beside the earcup. Then walk the white 3-pin JST battery plug (red +, white NTC thermistor, black −) straight out of its board socket.

  4. 4Release and lift out the 3.7 V lithium-ion pouch battery

    Slide the flat blade of the nylon spudger slowly beneath the edge of the 3.7 V lithium-ion pouch battery (Sony LIS1662HNPC in the WH-1000XM4, or SP624038 in the WH-1000XM5) to ease it off its double-sided adhesive pad above the NFC and capacitive touch-sensor panel. Lift the old pouch cell out and place it in the tray.

  5. 5Unscrew the swivel hinge retainer & thread the wire harness trap

    Unscrew the 2 × 1.7 × 5.0 mm Phillips #00 screws holding the internal swivel hinge retainer clip at the top of the earcup, lift off the retainer clip, and carefully thread the multi-strand cross-headband wire harness through the slot of the pivot joint to free the broken swivel hinge yoke. Avoid this trap: The multi-conductor wire harness connecting the left and right earcups passes directly through the hollow center of the swivel hinge post. If the wire bundle slips out of its recessed guide groove while you screw down the internal hinge retainer clip, the plastic rib pinches through the thin insulation—cutting off audio, ANC microphones, or power between the earcups.

What you need

Questions

How do the Sony WH-1000XM4 and WH-1000XM5 earpads come off?

Both use a rigid plastic mounting ring bonded to the base of the earpad cushion with 6 perimeter snap tabs. Slip a flat plastic pry tool under the inner rim of the earpad and work around the oval perimeter until all 6 clips pop free—do not pull on the soft leatherette foam alone.

Which earcup holds the battery on the Sony WH-1000XM4 and WH-1000XM5?

The 3.7 V / 3.8 V lithium-ion pouch battery sits inside the Right (R) earcup alongside the NFC coil and capacitive touch-sensor panel. The Left (L) earcup holds the main USB-C charging port, power/NC buttons, and primary audio board.

Why does my Sony WH-1000XM4 or XM5 blink red and refuse to charge after a battery swap?

Sony’s charging circuit monitors the middle white wire on the 3-pin JST battery plug, which connects to an internal 10 kΩ NTC thermistor inside the battery pack. If the plug is not seated squarely or a cheap 2-wire cell without a working thermistor is used, the headphone aborts charging.

Can you replace a broken Sony WH-1000XM4 or XM5 swivel hinge without soldering?

You can replace the outer folding hanger fork or re-seat a popped swivel C-clip without soldering by unclipping the internal pivot retainer and threading the slack of the wire harness through the slot in the yoke. If the full closed-loop swivel housing is replaced from scratch, check whether your replacement kit uses a split-slot yoke or requires unpinning the micro-connector on the board.

Safety

Switch the headphones off and unplug any USB-C cable before opening the earcup. Unplug the 3-wire battery JST connector before working near the circuit board or hinge screws, and never pry the foil lithium-ion pouch battery with a metal screwdriver.

About this teardown

3D Spatial Reconstruction: Models are engineered from factual hardware measurements to visualize internal layouts, screw lengths, and hidden cable traps before you open your device. Always verify cable routing on your specific hardware revision.

This 3D teardown models the right earcup architecture shared across Sony’s flagship WH-1000XM4 and WH-1000XM5 wireless noise-cancelling headphones: an oval snap-on earpad mounting ring with 6 perimeter clips, a removable open-cell acoustic foam damper, an angled driver baffle plate held by 4 × 1.7 × 5.0 mm #00 Phillips screws, an internal ZIF ribbon cable linking the inner ANC feedback microphone and capacitive touch sensor panel, a 3.7 V / 3.8 V 3-wire lithium-ion pouch battery (Sony LIS1662HNPC / SP624038), and the top swivel hinge yoke assembly with the cross-headband wire harness threading through the hollow pivot post.

The two classic DIY failures are modeled directly as interactive 3D traps: pulling the unscrewed driver baffle plate straight off before flipping the ZIF ribbon latch, and clamping the replacement swivel hinge retainer clip down over a stray loop of the cross-headband wire bundle.

Sources: iFixit: Sony WH-1000XM4 Battery Replacement & Earpad Disassembly (6-clip snap-on earpad ring, foam insert, 4 × 5.0 mm Phillips #00 baffle screws, LIS1662HNPC 3.7 V 1050 mAh 3.9 Wh pouch battery), iFixit: Sony WH-1000XM4 Swivel Hinge & Hanger Replacement (routing the cross-headband wire harness through the pivot joint and securing the internal retainer clip), iFixit: Sony WH-1000XM5 Teardown & Repair Reference (30 mm driver baffle, 6-clip earpad ring, SP624038 3-wire battery, stepless slider swivel joint), Price: Target Certified Refurbished, Sony WH-1000XM4, $159.99, out of stock when read (new WH-1000XM5: $399.99; 9 November 2026), Price: Apolonia on Tindie, stainless steel WH-1000XM4 hinge, $15 for two, a third-party part (9 November 2026).

The 3D models, drawings and text are our own. Sony, WH-1000XM4 and WH-1000XM5 are trademarks of their owners, named only to say which device this teardown is for; iTakeApart is not affiliated with them.