2018–2026 Tesla Model 3 & Model Y Cabin Air Filter Replacement (T20 Torx & Dual Filters)Tesla Model 3 / Model Y cabin filtersTesla Model 3/Y filters

Steps ↓
✓ Spec-Researched Risk: Low 15–20 min
What you need6 steps · press play

3D Spatial Reconstruction: models are engineered from factual measurements to show the parts, the fixings and the order of the job before you start. Always check the handbook of your own car.

iTakeApart.com is an independent platform creating original 3D teardown and repair instructions. We are not affiliated with, endorsed by, or sponsored by Apple, Samsung, Sony, Nintendo, Microsoft, Valve, Dyson, Nespresso, Meta, Ray-Ban, Oura, Tesla, or any other manufacturer or brand mentioned. All product names and trademarks belong to their owners and are used only to identify the devices a guide is for (nominative fair use). Opening a device may void its warranty; you work on it at your own risk.

Embed this 3D guide

Paste it into an article, a blog post or a forum that allows iframes: your readers get the full 3D player (orbit, steps, X-ray, the part to buy) with a link back to this repair guide.

Preview ↗

Free for press, blogs, repair forums and classrooms. Embed this interactive 3D guide freely on your site or in your article: just keep the "Interactive 3D by iTakeApart.com" credit badge and its link intact. Commercial, OEM or white-label use needs a partner licence (Terms).

Search nearby garages

Opens local search results in Google Maps for your car and a postcode or city. We do not check, rate or recommend the garages it shows.

Open Google Maps directly ↗

What you type goes only into the Google Maps search: we do not keep it or send it anywhere.

Before you open itDIY or a repair shop?
Overall repair riskLow
Time required15–20 min
What can go wrongTearing the footwell speaker/LED wire by yanking the under-dash panel down, forgetting the lower filter of the stacked pair, or pointing AIR FLOW forward.
Cost comparison DIY: a pair of Tesla filters, $40 ($20 each)Get the part ↗Get the kit ↗ Garage: varies by shopSearch nearby garages ↗Opens local search results in Google Maps US prices, checked November 2026; they vary by shop and country.
Fix vs. Replace

Fix it yourself, pay a repair shop, or replace it?

FaultClogged cabin air filters

Your time is worth
Fix it yourself$47
  • Part$40
  • Toolsnot priced
  • Time15–20 min
  • 3D risk levelLow
Repair shopNo sourced figure
New or refurbishedUpkeep: nothing to replace
No verdict: a figure is missingNothing to buy new, and no sourced shop price to compare with: no verdict.

How the verdict works: our own rules of thumb, not statistics. DIY wins when the 3D risk is low or medium and doing it yourself saves over 40% against a replacement (against a shop’s price where buying new does not apply). Replace instead when the device is sealed or potted, or the repair costs over 60% of a replacement. Consider a shop when the risk is high, the job needs soldering or it has a delicate ribbon-cable trap. Your time counts at the rate you pick. Figures are estimates in US dollars, read on makers’ and shops’ own pages in November 2026; they vary by shop and country, and the pages are listed with the guide’s sources. The links open a shop search; we earn nothing from them. Compare other devices in the Fix or Replace? calculator →

Measurements in

6 steps · T20 Torx + trim tool · 2018–2026 Tesla Model 3 & Model Y · 2× #CF12774 / 1107681-00-A

2018–2026 Tesla Model 3 & Model Y Cabin Air Filter Replacement (T20 Torx & Dual Filters): interactive 3D repair guide

✓ Spec-Researched 3D Guide

Unlike almost every other vehicle on the road, the 2018–2026 Tesla Model 3 and 2020–2026 Model Y do NOT put the cabin air filter behind the glovebox: instead, TWO vertically stacked cabin filters (2× #CF12774 / OEM 1107681-00-A) sit inside the center console wall on the left side of the front passenger footwell, held behind a carpeted side panel and a T20 Torx screw.

What you need

Unlike gas cars where the cabin filter sits horizontally behind the glovebox, the 2018–2026 Tesla Model 3 and 2020–2026 Model Y house TWO stacked vertical cabin air filters (2× #CF12774 / OEM 1107681-00-A) inside the left wall of the front passenger footwell (the right side of the center console). You need a T20 Torx driver and a plastic trim tool.

Tools: T20 Torx screwdriver, Plastic trim pry tool

Exact Tesla Model 3 & Model Y Revisions & Part Numbers

Tesla Model 3 & Model Y Cabin Air Filter Revisions & Exact Part Numbers

Every 2017–2026 Tesla Model 3 and 2020–2026 Model Y requires TWO (2×) 243 × 140 × 30 mm cabin air filters stacked vertically inside the center console footwell wall:

Vehicle & YearsHVAC Cover RevisionFootwell & Harness DetailsExact Part # (2 Filters Required!)Arrow & Ribbon Rule
Tesla Model 3 (2017–2020)Early revision (T20 Torx screw at TOP of vertical cover)4 push-rivets under dash + footwell LED & speaker plug + 7-clip console carpet side panel2× Tesla OEM 1107681-00-A · FRAM #CF12774 (×2) · Bosch P3985WS (×2)AIR FLOW points REARWARD (pull ribbons face OUT)
Tesla Model 3 (2021–2023) & Highland (2024–2026)Heat-pump revision (T20 Torx screw at BOTTOM + magnetic catch)4 push-rivets under dash + orange speaker plug + 7-clip console carpet side panel2× Tesla OEM 1107681-00-A · FRAM #CF12774 (×2) · Mann FP 25 015 (×2)AIR FLOW points REARWARD (pull ribbons face OUT)
Tesla Model Y (2020–2026 RWD, Long Range & Performance)Vertical cover with T20 Torx screw + magnetic catch4 push-rivets under dash + footwell LED & orange speaker plug + 7-clip console carpet panel (plus front-trunk HEPA filter on 2021+)2× Tesla OEM 1107681-00-A · FRAM #CF12774 (×2) · Bosch P3985WS (×2)AIR FLOW points REARWARD (pull ribbons face OUT)

Why You Must Buy 2 Filters (2× #CF12774): Single aftermarket boxes often contain only 1 filter. Both the Tesla Model 3 and Model Y stack two identical 243 × 140 × 30 mm filters one on top of the other inside the vertical center-console cavity—make sure you purchase a 2-pack or two individual boxes!

Before you open it: the risk map

X-ray view of the 2018–2026 Tesla Model 3 & Model Y passenger footwell: the 4 under-dash push rivets, the footwell puddle LED and orange speaker connector, the 7-clip carpeted center-console side panel, the T20 Torx screw on the vertical HVAC cover, and the two stacked filters.

Footwell wiring & high-voltage harness cautions

Push rivets, console clips & T20 Torx screw

Press X-Ray & Danger Zones (K) on the player to see them in 3D, through the closed car.

All 6 steps

  1. 1Move passenger seat back & clear the passenger footwell

    Tap Controls > Safety > Power Off (or turn off Climate Control) on the central touchscreen so the blower fan is off. Open the front passenger door wide, slide the front passenger seat all the way back, and clear the footwell so you have room to kneel and reach under the dashboard.

  2. 2Pop the 4 under-dash push clips & unplug the speaker/light harness trap

    Use a plastic trim tool or your fingernail to pry out the center pins of the 4 plastic push-rivets holding the black under-dash acoustic panel beneath the glovebox. Lower the panel gently by a few centimetres, then press the release tabs to unplug the footwell puddle LED light and the orange pedestrian/emergency speaker wire connector before setting the panel aside. Avoid this trap: If you pop the 4 push-rivets and yank the under-dash acoustic panel straight down into the footwell without unplugging the puddle light and orange speaker harness first, the short wire leads pull taut and rip the pins out of the connector housing.

  3. 3Pull back the carpeted center-console side panel in the footwell

    Look at the left wall of the passenger footwell (the carpeted right side of the center console). Starting at the top-front corner under the dash, pull the carpeted side panel outward toward the passenger door to pop its 7 plastic friction clips loose, exposing the vertical black HVAC filter cover on the side of the center console.

  4. 4Remove the T20 Torx screw & unhook the vertical HVAC filter cover

    On the exposed side of the center console HVAC box, locate the vertical black plastic filter cover. Use a T20 Torx screwdriver to remove the single T20 Torx screw (at the top of the cover on 2018–2020 models, or at the bottom alongside a magnetic catch on 2021–2026 models), then unclip and lift the vertical cover off.

  5. 5Pull the fabric ribbon tabs to extract BOTH stacked cabin filters

    Tesla stacks TWO cabin filters vertically inside the slot. First, pull the fabric ribbon tab on the UPPER filter to slide it straight out into the passenger footwell. Next, grab the ribbon tab on the LOWER filter, lift it upward into the upper slot position, and slide the second filter out into the footwell.

  6. 6Point AIR FLOW arrows toward the REAR of the car & install both filters trap

    Check the AIR FLOW arrows on both new #CF12774 (OEM 1107681-00-A) filters: in a Tesla Model 3 and Model Y, the AIR FLOW arrows must point toward the REAR of the car (toward the back seats) and the fabric pull ribbons must face outward toward you! Slide the first filter in and push it DOWN into the lower cavity, then slide the second filter in directly above it. Avoid this trap: In the Model 3 and Model Y, fresh air enters from the front trunk intake and flows rearward through the vertical evaporator housing. Installing the filters with the AIR FLOW arrows pointing toward the front of the car reverses the activated carbon layer—and if the pull ribbons face inward, you will have no tab to pull the lower filter up at the next service!

What you need

Questions

Where is the cabin air filter located on a Tesla Model 3 and Model Y?

It is NOT behind the glovebox. On both the Tesla Model 3 and Model Y, two stacked cabin air filters are mounted vertically inside the left wall of the front passenger footwell (the right side of the center console), behind the carpeted side trim panel.

Which way do the AIR FLOW arrows point on Tesla Model 3 and Model Y cabin filters?

Point the AIR FLOW arrows toward the REAR of the car (toward the back seats), and make sure the fabric pull ribbons face OUTWARD toward the passenger door so you can pull both filters out at the next service.

What tool size is needed for the Tesla Model 3 / Model Y cabin filter cover screw?

The vertical HVAC filter cover uses a single T20 Torx screw (located at the top of the cover on 2017–2020 Model 3s, and at the bottom of the cover alongside a magnetic latch on 2021–2026 Model 3 and Model Y vehicles).

How many cabin air filters does a Tesla Model 3 or Model Y take?

Two! Every Model 3 and Model Y stacks two identical cabin filters (2× OEM 1107681-00-A / 2× FRAM #CF12774, each 243 × 140 × 30 mm) vertically inside the center console slot. Slide the first filter in and push it down into the lower cavity, then slide the second filter in on top of it.

Safety

Power off Climate Control from the touchscreen before starting. Never pry on or lean tools against the bright orange high-voltage wiring harness near the front of the center console HVAC box.

About this guide

3D Spatial Reconstruction: models are engineered from factual measurements to show the parts, the fixings and the order of the job before you start. Always check the handbook of your own car.

This 3D guide models the official Tesla DIY procedure for replacing the two stacked cabin air filters (OEM 1107681-00-A / FRAM #CF12774) on all 2017–2026 Tesla Model 3 (including the 2024+ Highland refresh) and 2020–2026 Tesla Model Y vehicles.

Because the Model 3 and Model Y package the evaporator core vertically inside the center console tunnel rather than horizontally behind the glovebox, both cabin filters are accessed from the passenger footwell by lowering the under-dash acoustic panel, pulling back the carpeted right side of the center console, and removing a single T20 Torx screw.

Sources: Tesla Official Do It Yourself Guide: Replacing the Cabin Air Filter on Model 3 & Model Y (2-year interval, T20 Torx screw, 2 stacked filters, arrows toward rear of vehicle), FRAM #CF12774 & Mann-Filter FP 25 015 Specifications (243 × 140 × 30 mm for Tesla Model 3 & Model Y), Price: Tesla Shop, Model 3/Y Air Filter, $20, sold individually, two needed for a change (read 9 November 2026).

The 3D models, drawings and text are our own. The 3D cabin is an unbadged reconstruction of this vehicle’s own layout, from its maker’s procedure and the sources above, not the maker’s own model or a scan. Tesla, Model 3, Model Y, FRAM, Bosch and Mann-Filter are trademarks of their respective owners, named strictly in text to indicate mechanical compatibility and fastener/part specifications (nominative fair use); iTakeApart is not affiliated with or endorsed by any vehicle manufacturer.